WALI Dual Monitor Desk Mount Instruction Manual
- June 7, 2024
- WALI
Table of Contents
INSTALLATION MANUAL Dual Monitor Desk Mount
M002
Supplied Parts List
www.walielectric.com
support@walielectric.com
1-844-SATTLER (18447288537)
WARNING
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by an
improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT
TIPOVER:
NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF THE MONITOR
OR STAND. USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
USE OF TIP-OVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE THE RISK OF TIP-
OVER.
SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
Supplied Parts List
1.Measure the thickness of your mounting surface or desk.
2. Option A: Clamp Installation
-
Connect Pole a and C-Clamp Brace c from the bottom using M5x14 Bolt f and tighten with Allen Key 3mm o.
-
Select the preferred height according to your desk thickness. Connect C-Clamp b to C-Clamp Brace c using M8x12 Bolt g and tighten with Allen Key 5mm o. Rotate the hand knob clockwise to fasten for stability.
Option B: Grommet Base Installation
- Place Pole a onto Grommet Base Plate m. Connect them from the bottom using M5x14 Bolt f and tighten with Allen Key 3mm o.
2a. Existing Grommet Hole Installation
If the existing grommet hole comes with a plastic protector, remove it to
ensure a flat surface before installing the desk mount. Position the Pole
a on the mounting surface and secure using the Support Plate j , M10
Washer k , Spring Washer l , and M10 Bolt i . Fasten the Bolt
using the provided Wrench p.
2b. Self-drilled Grommet Hole Installation
Mark the position of the hole on your mounting surface. Drill a 3/8″(10mm)
diameter hole at the marked position through the mounting surface. Position
the Pole a on the mounting surface and secure using the Support Plate
j , M10 Washer k , Spring Washer l , and M10 Bolt i. Fasten
the Bolt using the provided Wrench p.
**3.**Put the Wire Clip n1 and Swivel Arm d through the Pole a
, adjust the preferred height, and tighten using Allen Key 6mm o . Attach the
Wire Clips n1 to the Swivel Arm d . 
**4.**Select bolts and spacers (if needed)
according to your TV/Monitor. Attach the VESA Plate to the Monitor and tighten
with a screwdriver. (Screwdriver not included)
5. Put the assembled TV/Monitor onto the Swivel Arm d and tighten the
VESA Plate e with Nut h for stability.
**6.**If one monitor is lower, remove the Nut h and turn the bolt
counter-clockwise using Allen key 3mm o to raise the monitor. Tighten the
VESA Plate e with Nut h for stability after the adjustment.
**7.**Guide the cable through the Wire Clips ( n1, n2 ) and store the
Allen Keys o in the Wire Clip n1 . Adjust the tilt angle using Allen
Key 5mm n .
8.Manually swivel, tilt, and rotate the monitor for the best viewing angle.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>