WALI SWM202 Speaker Wall Mount Instruction Manual
- May 15, 2024
- WALI
Table of Contents
WALI SWM202 Speaker Wall Mount
Speaker Wall Mount
- Model Numbers: SWM202 / SWM402 / SWM602
- Rated Load Capacity: 22.7kg/50lbs
- Website: www.walielectric.com
- Email: support@walielectric.com
- Phone: 1-844-SATTLER (18447288537)
Specifications
- SWM202 A (x2)
- M5x12 Bolt B (x4)
- M6x12 Bolt C (x2)
- 1/4 -20×1/2 Bolt D (x2)
- ST4.2X25 Screw E (x4)
- 6X25 Anchor F (x4)
Step 1: Surface Preparation
Ensure the supporting surface can safely hold the equipment and hardware.
Tighten wood screws securely without overtightening to prevent damage.
Mount screws in the center of studs using an edge-to-edge stud finder.
Step 2: Installation Options
Option A: Wood Stud Mounting
- Locate stud edges with a stud finder and mark the center of each stud.
- Place metal wall plate on the wall, mark hole centers, drill holes, and secure with screws.
Option B: Solid Brick and Concrete Wall Mounting
- Use the metal wall plate as a template to mark holes on the wall.
- Drill holes, insert Concrete Anchors, and attach the wall plate with screws.
Speaker Wall Mount
Do not hang Large size speakers from the brackets. Avoid the risk of instability of the center of gravity !
SWM202 / SWM402 / SWM602
www.walielectric.com
support@walielectric.com
1-844-SATTLER (18447288537)
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
! TIPOVER WARNING SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER.
TO HELP PREVENT TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
Supplied Parts List
-
Step 1
-
Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
-
Tighten wood screws firmly but
do not overtighten. Over tightening can damage the screws, greatly reducing their holding power. -
Make sure that mounting screws are anchored into the center of the studs. The use of an “edge to edge” stud finder is highly recommended.
-
-
Step 2
Option A : Wood Stud Mounting- Use a stud finder to locate the edges of the studs. Using an edge-to-edge stud finder is highly recommended based on their edges and drew a vertical line down each stud’s center.
- Place metal wall plate on the wall as a template. And mark the center of the two mounting holes. Make sure that the mounting holes are on the stud centerline.
- Drill two 1/8″ (3mm) dia. Holes 1″ (25mm) deep. Secure it using two screws E (part – ). Make sure that the wall plate is level as shown in the figure. Option B : Sold Brick and Concrete Wall Mounting
- Use the metal wall plate as a template to mark two holes on the wall as shown in the figure.
- Drill two 7/32″ (5.5mm) dia. Holes 1.2″ (30mm) deep. Insert a Concrete Anchor (Part- ) intoF each of these holes. Attach the wall plate to the wall using two Escrews (Part- ), make sure that the wall plate is level as shown in the figure.
-
Step 3
Hand thread bolts into the threaded inserts on the back of your Speaker to determine which bolt to use. Attach Speaker to top bracket using Bolts .B C D
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>