WALI M001S Single Monitor Desk Mount Instruction Manual
- June 1, 2024
- WALI
Table of Contents
INSTALLATION MANUAL
Single Monitor Desk Mount
M001S/M001S-W
M001S Single Monitor Desk Mount
WARNING
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual.
Do not exceed weight capacity. We cannot be liable for damage or injury caused
by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT
TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP
OVER.
SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
Supplied Parts List
-
Measure the thickness of your mounting surface or desk.
-
Option A : Clamp Installation
1. Connect Pole A and C-Clamp Brace 2B via tightening M5x14 Bolt J with the Allen Key3mm I.2. Remove the screw and washer at the top of the M10 Hand Knob B4 and connect the M10 handle B4 , C-clamp B1 and support plate with the screw and washer that were just removed. Remove the M8x12 Bolt on the C-clamp B1. Select the preferred height according to your desk thickness. Connect C-Clamp B1 to C-Clamp Brace B2 using M&x12 Bolt, and tighten with Allen Key 5mm I. Rotate the hand knob B4 clockwise to fasten for stability. Option B : Grommet Base Installation
I. Place Pole A onto Grommet Base Plate B8. Connect them from the bottom using M5x14 Bolt J and tighten with Allen Key 3mm I . 2a. Existing Grommet Hole Installation
Remove the screw and washer at the top of the M10 Hand Knob B4.
If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before installing the desk mount.
Position the Pole A on the mounting surface and connect the hand knob B4 through the Support Plate B7 and the grommet hole with the Pole A . Rotate the hand knob B4 clockwise to fasten for stability. 2b. Self-drilled Grommet Hole Installation
Remove the screw and washer at the top of the M10 Hand Knob B4 .
Mark the position of the hole on your mounting surface. Drill a 3/8″(10mm) diameter hole at the marked position through the mounting surface.
Position the Pole A on the mounting surface and connect the hand knob B4 through the Support Plate A and the self-drilled hole with the Pole A . Rotate the hand knob B4 clockwise to fasten for stability. -
Put the Wire Clip K and Monitor Arm C through the Pole A , adjust the preferred height and tighten using Allen Key 5mm I .
-
Select bolts and spacers (if needed) according to your TV/Monitor. Attach the VESA Plate to the Monitor and tighten with a screwdriver. (Screwdriver not included).
-
Put the assembled TV/Monitor onto the Monitor Arm C and tighten the VESA Plate D with Nut E for stability.
-
Adjust the tilt angle using Allen Key 5mm I .
-
Guide the cable through the Wire Clips K and store the Allen Keys I in the Wire Clip K .
-
Manually swivel, tilt, and rotate the monitor for the best viewing angle.
www.walielectric.com
support@walielectric.com
1-844-SATTLER (18447288537)
Documents / Resources
| WALI
M001S Single Monitor Desk
Mount
[pdf] Instruction Manual
M001S Single Monitor Desk Mount, M001S, Single Monitor Desk Mount, Monitor
Desk Mount, Desk Mount, Mount
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>