WALI M002-32 Dual Monitor Desk Mount Installation Guide

WALI M002-32 Dual Monitor Desk Mount

Specifications

• Model: M002-32
• Brand: Dual Monitor Desk Mount
• Manufacturer: Walielectric
• Contact: support@walielectric.com, 1-844-SATTLER (18447288537)

Product Usage Instructions

Option A: Clamp Installation

1. Connect Pole aa and C-Clamp Brace cc using M5x14 Bolt f and tighten with Allen Key 3mm oi.
2. Stick the EVA pad B o to the C-Clamp Brace cc.
3. Connect M10 Hand Knob mm and C-clamp b with the screw, washer, and top plate. Adjust to preferred height according to desk thickness.
4. Connect C-clamp b to C-clamp Brace cc using M8x12 Bolt g and tighten with Allen Key 5mm i.
5. Rotate Hand Knob m clockwise to fasten for stability.

Option B: Grommet Base Installation

1. Place Pole aa onto Grommet Base Plate mq using M5x14 Bolt f and tighten with Allen Key 3mm i.
2. Stick the EVA pad A no to the Grommet Base Plate q.

Existing Grommet Hole Installation:

1. Position Pole a on the mounting surface and connect the hand knob Nm through Support Plate p and the grommet hole with Pole aa.
2. Rotate Hand Knob Nm clockwise to fasten for stability.

Self-drilled Grommet Hole Installation:

1. Mark the position of the hole on your mounting surface and drill a 3/8(10mm) diameter hole.
2. Position Pole aa on the mounting surface and connect the hand knob mm through Support Plate p and the self-drilled hole with Pole aa.
3. Rotate Hand Knob mm clockwise to fasten for stability.

Final Steps:

1. Put Wire Clip hr and Arm dc through Pole aa, adjust height, and tighten using Allen Key 5mm oi. Attach Wire Clips sl to Arm dc.
2. Select appropriate bolts and spacers for your TV/Monitor.
   Attach VESA Plate to the Monitor and tighten with a screwdriver.

Frequently Asked Questions

Q: What should I do if I have difficulties in determining the correct screw size for my monitor?

A: Hand thread screws into the threaded inserts on the back of your monitor to determine which screw (M4x12 or M4x30) to use.

WARNING
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

TIP OVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
• USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
• SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

Supplied Parts List

INSTALLATION

Option A : Clamp Installation

1. Connect Pole a and C-Clamp Brace c from the bottom using M5x14 Bolt f andf tighten with Allen Key 3mm .i

2. Remove the screw, washer and top plate from the M10 Hand Knob m , then connect the M10 Handm m bKnob m and C-clamp b with the screw, washer and top plate that were just removed.
   Select the preferred height according to your desk thickness. Connect C-clamp b to C-clamp Brace cb c gusing M8x12 Bolt g , and tighten with Allen Key 5mm i . Rotate the Hand Knob m clockwise to fasteni m for stability.

Option B : Grommet Base Installation

1. Place Pole a onto Grommet Base Plate . Connect them from the bottom using M5x14 Bolt and tighten with Allen Key 3mm .i

Existing Grommet Hole Installation
Remove the screw, washer and top plate from the M10 Hand Knob M. If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before installing the desk mount. Position the Pole a on the mounting surface and connect the hand knob m through the Support Plate p and the grommet hole with the Pole a. Rotate the hand knob m clockwise to fasten for stability.

Self-drilled Grommet Hole Installation

• Remove the screw, washer and top plate from the M10 Hand Knob m. Mark the position of the hole on your mounting surface. Drill a 3/8″(10mm) diameter hole at the marked position through the mounting surface.
• Position the Pole on the mounting surface and connect the hand knob * through the Support
• Plate pand the self-drilled hole with the Pole a.
• Rotate the hand knob m clockwise to fasten for stability.

Put the Wire Clip r and Arm d through the Pole a, adjust the preferred height and tighten using Allen Key 5mm i. Attach the Wire Clips s to the Arm d .

Select bolts and spacers (if needed) according to your TV/Monitor. Attach the VESA Plate to the Monitor and tighten with a screwdriver. (Screwdriver not included)

Place the assembled TV/Monitor onto Arm, tighten the VESA Plate with Nut h for stability.
Adjust the VESA Plate laterally shifting along the Arm d, using Allen Key i.

Place the assembled TV/Monitor onto Arm , tighten the VESA Plate with Nut h for stability.
Adjust the VESA Plate laterally shifting along the Arm d , using Allen Key i .

Guide the cable through the Wire Clips ( r,s ) and store the Allen Keys o in the Wire Clip. Adjust the tilt angle using Allen Key 5mm i.

Manually swivel, tilt, and rotate the monitor for the best viewing angle.

www.walielectric.com
support@walielectric.com
1-844-SATTLER (18447288537)

References

• TV mount, Monitor mount, Desk mount, TV Stand, Speaker mount,

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>