WALI 1343LKS Full-Motion TV Wall Mount Installation Guide
- June 3, 2024
- WALI
Table of Contents
WALI 1343LKS Full-Motion TV Wall Mount
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. This product is designed to be
installed on wood stud walls, solid concrete walls or brick walls. Do not
mount on drywall alone. We cannot be liable for damage or injury caused by
improper mounting, incorrect assembly, or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN occUR FROM TIPOVER.
TO HELP PREVENT TIPoVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
Supplied Parts List
Step 1
Twist the knob as the image shown to release the knob and washer.
Step 2
Option A Wood Stud
If installing this product on wood stud, mark the position with Bubble
Level H & pencil on the wall. Drill 3/16″(4.5mm) diameter x 2.2″(55mm) length
holes at the marked position, attach the mount to wood stud and tighten using
Bolt W-A with screwdriver. Fix Décor Cover C onto the front of mount part.
(Screwdriver not included)
Option B Concrete Wall
If installing this product on concrete wall, mark the position with Bubble
Level H & pencil on the concrete wall. Drill 3/8″(10mm) diameter x 2.4″(60mm)
length holes at the marked position, attach the mount to concrete wall and
tighten using Bolt W-A & Concrete Anchor W-B with screwdriver.Fix Décor Cover
C onto the front of mount part. (Screwdriver not included)
Step 3
Twist the knob on the VESA Plate B to open the arm and ensure the arm is
vertical.
Step 4
-
Select TV Screws
-
**Select Spacers ( if needed )
**
- Select M4x14 Bolt M-A or M5x14 Bolt M-B according to your TV/Monitor specification, connect VESA Plate B together with D5 Washer M-E into the mounting holes on the back of TV/Monitor, tighten with screwdriver.(Screwdriver not included)
- Select M4x14 Bolt M-A or M5x14 Bolt M-B according to your TV/Monitor specification, connect VESA Plate B together with D5 Washer M-E and Spacer M-G into the mounting holes on the back of TV/Monitor, tighten with screwdriver.(Screwdriver not included)
- Select the VESA size according to TV/Monitors specification as shown in image, connect the Adapter D & Adapter E to VESA Plate B using Bolt F ,Nut G to tighten with wrench and screwdriver.(Wrench and Screwdriver not included)
- Three options are available for multiple TV/Monitor specifications.
- Connect M4x14 Bolt M-A or M5x14 Bolt M-B together with D5 Washer M-E ,Spacer M-G and tighten with screwdriver;
- Connect M6x14 Bolt M-C together with D8 Washer M-F ,Spacer M-G and tighten with screwdriver;
- Connect M8x20 Bolt M-D together with D8 Washer M-F , 2 pcs Spacer M-G and tighten with screwdriver; (Screwdriver not included)
Step 5
Twist the knobs to adjust the arm to be away from wall as image shown.
Step 6
Place the assembled TV/Monitors onto the Arm A , twist the knob as shown in
image (#1) to tighten the VESA Plate B . Twist the bottom knob as shown in
image (#2) to tighten the whole arm.
Step 7
To ensure the integral stability of the mount, fully tighten knobs using Allen
Key I each time after adjusting preferred angle and extension. (Do NOT tighten
knobs only by hand alone). Guide the cable through the clip holder on the arm
as shown in image (#2).
Step 8
Angle Adjustments.
Thank you for chosing us
We support the technology that brings your home to life. We offer high quality products, professional customer service, and extensive technical support.
If you have any questions,please contact us.
1-844-SATTLER (18447288537) support@walielectric.com