TAKSTAR E500W Wireless Amplifier User Manual

June 7, 2024
TAKSTAR

TAKSTAR E500W Wireless Amplifier

TAKSTAR-E500W-Wireless-Amplifier-produivt

Preface
Dear Customer,
Thank you for purchasing Takstar E500W Wireless Amplifier. In order to better
understand and use the product, please read this manual carefully. If you have
any questions or suggestions, please contact our local dealer.

Features

  • Wireless amplifier with dual voice coil speaker, powerful magnet, 20W high power, and clear audio.
  • UHF wireless technology, about 40m use range in area without obstruction and interference.
  • 40 adjustable channels (Channel A: CH01-20; Channel B: CH21-40), and ability to use multiple sets simultaneously.
  • Built-in anti-interference wireless module for dual mic application. Optional rechargeable handheld or headset mics.
  • Digital Signal Processor (DSP) chip inside effectively suppresses feedback.
  • Wireless playback for a simpler music experience untethered by tedious wiring.
  • Support a variety of audio inputs including USB drive, TF card and AUX inputs.
  • Equipped with an LED display for clear overview of amplifier status in real time.
  • Built-in large-capacity lithium-ion battery lasts around 12hrs operation (80% volume).
  • Strap across shoulder or around waist, any way you like.
  • Stylish, designed in accordance with ergonomic principles.

Application

  • Teaching, meeting, training, tour guide, sales, etc.

Package Contents

  • E500W Amplifier…………………………………………………………………………… 1 PCS
  • Wireless Handheld Microphone……………………………………………2 PCS (optional)
  • Wireless Headset Microphone………………………………………………2 PCS (optional)
  • Wired Headset Microphone.…………………………………………………1 PCS (optional)
  • Shoulder Strap…………………………………………………………………………………1 PCS
  • Type-C Charging Cable……………………………… 1 PCS
  • User Manual……………………………………………………………………………………1 PCS

Specifications

Amplifier

  • Charging Voltage: DC 5V/1A
  • Charging Time: about 2.5 hours
  • Playtime: about 12 hours (80% volume)
  • Net Weight: about 420g
  • Dimensions: 130×102×46mm
  • Frequency Response: 80Hz-18KHz
  • Rated Power: 10W
  • Peak Power: 20W
  • Speaker Impedance: 4Ω
  • Operating Voltage: DC 6.4-8.4V
  • Battery: 18650, 3.7V/2500mAh * 2PCS

Transmitter (Wireless Handheld Mic)

  • Capsule: back electret
  • Polar Pattern: unidirectional
  • Frequency Response: 60Hz-16KHz
  • Battery Type: lithium-ion battery
  • Sensitivity: -51 to -54dB (0db=1V/Pa/m at 1kHz)
  • UHF Frequency: 657.3MHz-667.05MHz (segmented)
  • UHF Use Distance: about 40m in open area
  • Battery Capacity: 18650, 3.7V/2000mAh * 1 PC.
  • Charging Specification: DC 5V/1A
  • Charging Time: about 2.5 hours
  • Playtime: about 20 hours
  • Net Weight: about 150g
  • UHF Use Distance: about 40m in open area
  • Battery Capacity: 3.7V/400mAh
  • Charging Specification: DC 5V/300mA
  • Charging Time: about 2 hours
  • Playtime: about 4 hours
  •  Net Weight: about 39g
  • Capsule: back electret •
  • Polar Pattern: unidirectional
  • Frequency Response: 60Hz-16KHz
  • Sensitivity: -44 to -50dB (0db=1V/Pa/m at 1kHz)
  • Battery Type: lithium-ion battery

Note :The above data are measured by Takstar laboratory which has the final interpretation right!

Function Descriptions

Voice Amplifier

TAKSTAR-E500W-Wireless-Amplifier- \(2\)

E500W Wireless Amplifier

  1. Power switch: rotate the dial to MAX until you hear a click to power on the device and then gradually increase the volume level. Once powered on, the LED display shows “UHF”, meaning the device is ready for voice amplification. Likewise, rotate to OFF to gradually decrease the volume level and eventually power off the device when you hear a click.

  2. LED digital display: display information such as the current work mode, battery level and mic working channel. It shows “BLUE” in Bluetooth mode, “HLOH” in karaoke mode, “TF” in TF card mode, “USB” in USB mode, “AUX” in audio input mode, and “REC” in recording mode (Note: you can only switch to recording mode when a storage device and a mic are both connected). is the battery level symbol which flashes when power is low (less than 1 hour left) and requires charging in time. “— — — —” shows up when the amplifier is in standby status which can be wakened up by any key press.

  3. M mode button: when powered on, press it to switch among six work modes, accompanied by corresponding voice prompt. In karaoke mode, long press M button to switch among low-reverb, medium-reverb and high-reverb settings. Once an AUX audio source or a TF card is inserted, the device will automatically switch to AUX mode or TF mode, and upon disconnected, switch to the next work mode. While a storage device and
    a mic are connected, long press this button to enter recording mode, accompanied by a “REC” symbol on LED display and a “Recording mode” voice prompt. During recording, the LED display shows recording duration in “00:00” format. Long press this button again to exit and save recording. Upon exiting recording mode, the device will automatically play the newly recorded audio in a loop.

  4. Play/Pause button: press it to play or pause the music. When playing in Bluetooth, long press this button to disconnect Bluetooth, followed by a voice prompt “Bluetooth disconnected”; long press this button again to reconnect Bluetooth, followed by a voice prompt “Bluetooth connected”. When playing music in TF card mode or USB mode, long press this button to loop a single song, accompanied by a single loop symbol ; long press this button again to cancel single-song loop, and the symbol will disappear.

  5. Next track button: press to switch the next track.

  6. Previous track button: press to switch to the previous track.

  7. MIC input interface: insert a wired mic to start wired voice amplification.

  8. AUX input interface: connect to a playback device (e.g., phone, tablet, MP3 player) via a Ø3.5mm audio cable, so to use the amplifier as an active speaker.

  9. TF card slot: insert a TF memory card following the labeled direction until you hear a click to install it in place. To remove the TF card, press it down until it clicks to eject the card.
    Tip: Please make sure the audio files in the TF card are stored in MP3 and/or WAV format, otherwise it won’t be readable and may even damage the device. Please format the TF card to FAT16 or FAT32 file system before copying songs, because other file system (e.g., exFAT, NTFS) will cause failure to save recordings or play songs.

  10. USB interface: insert a USB flash drive to play audio files.

  11. Charging port: charge the amplifier via a Type-C charging cable.

  12. Strap clip: used to install the shoulder strap for wearing the amplifier across shoulder.

Handheld Microphone

  1. Power button: long press it to turn on/off the mic. When powered on, press it twice to start pairing, or press it once to change frequency. When powered off, long press it for 10 seconds to switch between A/B channel. Note: A/B channel switching is only applicable for the dual-channel model, not for the single-channel model.
  2. Indicator light: lights up green when powered on and battery level is normal; flashes red if low power and requires charging; illuminates solid red while charging and turns solid green when fully charged. When the mic is powered off, long press its power button for 10 seconds until the indicator flashes green to switch channel A/B, and once switched successfully, the indicator will resume solid green.
  3. Charging port: charge the mic via a Type-C charging cable.

TAKSTAR-E500W-Wireless-Amplifier- \(7\)

Headset Microphone

TAKSTAR-E500W-Wireless-Amplifier- \(8\)

  1. Power switch: toggle switch to ON or OFF to power on or off respectively.

  2. Display: display working channel, mic volume and power status.

  3. M button: used for changing frequency, refer to “Pairing Method” section for details.

  4. [+] button: press to increase mic volume. In pairing mode, press or long press to gradually.

  5. [-] button: press to decrease mic volume. In pairing mode, press or long press to gradually.

  6. Charging port: connect to a USB data cable. Please use a standard 3C-certified 5V/1A adapter to charge the amplifier.

  7. Power indicator: light’s off when the power is off and not charging;
    lights up solid blue when powered on and power is sufficient; flashes blue
    if low power; illuminates solid red while charging and no longer red when fully charged.

  8. Working channel/mic volume: display the current operating channel by default. There are 40 available channels in total. Channel A can set CH01-20, while Channel B can set CH21-40. Volume level is displayed for 3s when you press volume [+]/[-] button, 9 levels in total, “U1-U9”. LED display goes off automatically after 10s

  9. High/Low power switch: press both [M] and [-] buttons at the same time to switch to low power, LED display shows E0; or press both [M] and [+] to switch to high power, LED display shows E1. (Use distance is around 10m when set to low power, or around 40m when set to high power)

Operation Instructions

Pairing Method
The products are paired by factory default and will automatically connect to each other once powered on. No extra pairing is required. If there is signal interference, follow the below steps to re-pair or change frequency:
Handheld Microphone:

  1. Pairing Method
  2. Power up both mics by long pressing their power buttons, their LED indicator should light up green. Then press their power buttons twice to enter pairing mode, indicated by flashing green LED indicator. Meanwhile, immediately power up the amplifier, wait until the flashing LED on handheld mic turns solid green to finish pairing. You should be able to hear voice amplification when talking to the mic.
  3. If there is no sound when you talk to the handheld mic, that means the pairing is not successful, please retry the above steps to re-pair.
  4. Changing Frequency
  5. Power up both the amplifier and handheld mic. After successfully paired, press the power button on the mic once to change frequency. If successful, the green indicator should flash for 1s before resuming solid green.
    Note: Wireless handheld mic A & B each has 20 adjustable frequency channels. Mic A: CH01-CH02; Mic B: CH21-CH40.

Headset Microphone:

  1. Pairing Method

  2. First, power off both the headset mic and the amplifier. Next, power up the headset mic, long press mic [M] button for 3s until its LED display shows a circle. Then, immediately power up the amplifier, wait until the headset mic’s LED circle changes into a static number. Talk towards the mic to test if your voice is amplified and if pairing is successful.
    If the amplifier is not powered on within 10s after the mic enters pairing mode, the mic will exit pairing mode and its LED circle will change back to a static number.
    No sound when talking to the headset mic means the pairing is not successful, please retry.

  3.  Changing Frequency

  4. Make sure that the headset mic and the amplifier are already paired, then power up both devices at the same time. Press the mic [M] button to change frequency, and the channel number on headset LED display will flicker. Then, press volume [+]/[-] button to cycle through frequency, and press [M] again to confirm frequency, or leave it auto confirmed after 3s idleness.

Bluetooth Pairing
Upon first use, you need to connect this device to your phone or Bluetooth device, following below steps:

  1. Power up the amplifier, press [M] to switch to Bluetooth mode and start Bluetooth discovery and pairing, indicated by a blinking “BLUE” symbol.
  2. Enter SETTINGS menu on your phone, find and enable Bluetooth, wait until “TAKSTAR E500W” is discovered and tap on it to connect. When connected successfully, there will be a voice prompt about “Bluetooth Connected”. Devices such as cell phones, laptops, tablets, and iPads can play music via Bluetooth thereafter.
  3. The next time you switch to Bluetooth mode, the amplifier will automatically connect to the previously paired device, signaled by a voice prompt “Bluetooth connected”.

Safety Instructions

To avoid electric shock, overheat, fire, radiation, explosion, mechanical risk and injury or property loss due to improper use, please read and observe the following items before use:

  1. Please check if the power of the connected equipment matches with that of this product before operation. Adjust the volume to proper level during operation. Do not operate at over-power or high-volume level for extended time to avoid product malfunction.

  2. If there is any abnormality during use (e.g., smoke, strange odor), please kill the power switch and unplug from power source, then send the product to the local after-sales service for repair.

  3.  Power adapter used, if any, should be approved by CCC certification or similar standards and comply with the power supply requirements.

  4. Keep this product and its accessories in a dry and ventilated area. Do not store in a humid or dusty area for extended time. Keep away from fire, rain, liquid intrusion, bumping, throwing, vibrating, or from blocking any ventilation openings, to prevent malfunction.

  5.  The product must, when installed on walls or ceilings, be fixed firmly in place at adequate strength to prevent from falling.
    Please abide by safety rules during operation. Do not use the product in places prohibited by laws or regulations to avoid accident.

  6. Do not disassemble or repair the product by yourself to avoid injury. If you have any questions or require any services, please contact our local after-sales service.

Label Meanings

This symbol indicates that this product should not be disposed of with your household waste, according to the WEEE directive (2012/19/EU) and your national law. This product should be handed over to an authorized collection site for recycling waste electrical and electronic equipment (WEEE). Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with WEEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, or your household waste disposal service.

About This Manual

This manual contains up-to-date technical specifications as of printing. However, specifications contained herein may not conform to your particular product since Takstar is constantly improving its products. Also, specifications, devices or accessories available may vary from region to region. If you have any questions, please contact our local sales outlet. For the latest version/more information, please visit our website: https://www.takstar.com/

xs@takstar.com
 www.takstar.com

Guangdong Takstar Electronic Co., Ltd. Address: No. 2 Fu KangYiRd., Longxi Boluo Huizhou, Guangdong 516121 China
Tel: 86 752 6383644 Fax: 86 752 6383952 Email: sales@takstar.com
Website: www.takstar.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals