TAKSTAR EX-3 Multifunctional Digital Power Amplifier User Manual

EX-3 Multifunctional Digital Power Amplifier
User Manual

E X – 3 Multifunctional Digital Power Amplifier

Preface
Dear Customer, Thank you for purchasing TAKSTAR EX-3 Multifunctional Digital Power Amplifier.
Please read the user manual carefully before use and keep it for future reference. If you have any questions or suggestions, please contact our local dealer.

Features

• 48kHz sampling rate, 32-bit DSP chip, 24-bit AD/DA conversion
• MIC channel with master volume control, phase, low cut, 9-band PEQ, noise gate, feedback controller and 4-way MIC independent volume control
• MIC effect with master volume control; echo with adjustable 5-band PEQ, delay and repetition; reverb with adjustable delay, time, space, high cut and low cut; independent phase control
• Music channel with master volume control; VOD, OPT, COAX, or BT for music input; independent volume control, 5-band PEQ and noise gate for VOD/SPDIF input
• Center output channel with independent volume control, 5-band PEQ, low cut, compressor, delay, phase and mute
• Bass output channel with independent volume control, 5-band PEQ, high cut, low cut, compressor, delay, phase and mute
• Front panel with IR receiving function, DSP with 16 user presets
• USB control interface for safe and easy operation
• High-end 5″ TFT color touch screen for you to directly control the volumes of music, microphone and effect, and to perform functions of calling presets, inputting selection, Bluetooth playback interface, microphone frequency matching and level display
• 50M bandwidth, 200 channels, PLL digital phase-locked loop multi-channel frequency synthesis
• Built-in 2X450/8 professional digital power amplifier for the main sound reinforcement system
• Startup delay to protect speaker
• Power amplifier with the anti-shock function when powering on/off

Handheld Wireless Microphone:

• Professional dynamic microphone
• LCD to display battery power and current frequency band
• Two AA batteries for the operation time of 4 hours
• 200 channels available for the switching between high power and low power

Quick Introduction to Frequency Matching

To make your wireless system work normally, the wireless handheld microphones and the power amplifier must be set to the same operating frequency.
Main Unit Settings

• The general setup method is that the main unit and microphones are kept within sight and the antenna is placed vertically.
• Connect the power cord to the main unit and turn on the panel power switch.
• Use standard speaker binding posts to connect the outputs  of the main unit to passive speakers.
• In the main interface, press the MIC A/MIC B button to enter the microphone receiver setting screen, rotate the encoder to change the frequency, and press the SYNC  button to set the frequency.

Wireless Handheld Microphone Settings

• Insert two AA batteries into the wireless microphone and press the power button to turn it on.

• The emitting window on the front panel of the main unit should be placed opposite to the infrared receiving window on the wireless microphone, and the distance should be kept at 15-30 cm.

• When the microphone is pairing with the main unit, the progress bar on the main unit screen will flash, and the wireless microphone screen will light up. When the channel on the wireless microphone screen is the same as that on the main unit screen, the pairing is successful.

• Long press the EDIT encoder on the panel to return to the main interface, or wait 10 seconds  Level Settings:

• When speaking or singing into the microphone, or using the microphone to connect to an instrument, it is at a normal level. Slowly adjust the volume of the panel to reach the level you want.

• If you find that the system shows frequency interruption or burst noise, it may be due to interference from other frequencies. Please follow the steps above to change the channel of the system, or check whether the antenna is installed correctly.

Front Panel

1. Power Switch The switch is used to turn on or off the main unit.
2. Music Volume This knob is used to adjust the volume of the input music in the range of 00-99.
3. Microphone Volume This knob is used to adjust the volume of the microphone in the range of 00-99.
4. Effect Volume This knob is used to adjust the volume of the effect in the range of 00-99. It is also an editing knob, which can be used to change some parameters.
5. IR SENSOR Window You can match the frequency in the IR SENSOR window (similar to selecting a TV channel through a remote control) and set a channel for the handheld microphone. You can also use the functions with the remote control.
6. Bluetooth Window The LED in this window will light up when Bluetooth is connected and light off when Bluetooth is disconnected.
7. TFT Touch Screen Through touch control, you can easily control the volumes of microphone, effect and music, as well as the functions of calling presets, inputting selection, Bluetooth playback and microphone frequency matching.
8. Function Keys for Frequency Matching Press MIC A to enter the frequency matching interface of microphone A and press MIC B to enter the frequency matching interface of microphone B. After selecting the frequency through the encoder, press SYNC to complete the frequency matching.

Rear Panel

1. BNC Antenna Connector: Allow full rotation to the best position. In normal operation, the antenna should be placed in a vertical position.
2. USB Port: Connect to the PC software through the USB port for the fine adjustment of internal parameters.
3. Optical Fiber Coaxial Input: It is an interface for optical fiber signal and coaxial digital signal.
4. REC Output Interface: It can be connected when recording is needed.
5. MIC Input Interfaces: Connect and expand the other two wired and wireless microphones. The input volume can be matched through PC software.
6. CENTER & SUBWOOF XLR Balanced Outputs: These two output ports can be connected to subwoofers and center speakers.
7. VOD Input: VOD audio input interface
8. Power Output Interfaces: Used to connect main speakers, with the red terminal connected to the positive pole and the black terminal connected to the negative pole.
9. Heat Dissipation Window: It is used to dissipate heat and ensure the normal operation of the equipment.
10. AC Power Input Socket: Connect to a qualified and matched AC power supply through a power cord.
11. Fuse: Protect the whole machine from being burnt out by strong electricity.

LCD Display

Main Menu Display

1. Effect Volume
2. Microphone Volume
3. Music Volume
4. Bluetooth Interface
5. Input Selection: VOD, OPT, COAX, BT
6. User Preset Selection: Different scene modes can be called.
7. Input Level Display
8. Output Level Display

Microphone receiving display interface

Wireless Microphone

1. LCD Display: Display current frequency, channel and battery power.
2. Power Switch: Press it to turn on the power and long press it to turn off the power.
3. High/Low RF Switch: high and low transmit power.
4. Battery Holder: Insert two standard AA batteries, and make sure not to reverse the polarity of the batteries.

Note: Do not insert the batteries backward because it will damage the microphone and you will not get a warranty.
Remote Control

1. Mute Button: Press it for the mute function and press it again to cancel the mute function.
2. Volume Control Buttons: Adjust the volumes of  music, effect and microphone.
3. Source Select Button: Choose from VOD, OPT,  COAX, BT.
4. User Preset Buttons: U01-U06 are user presets, and the current preset can be called.

Note: The remote control only works in the main menu interface, but not in the wireless microphone display interface.

PC Software
Reminder: The required PC control software and product manual are saved in the attached CD.
USB Data Cable Connection

Steps of USB Cable Connection:

1. Click and install the PC control software. Press “Next” according to the default prompts until the software is successfully installed and then press “Finish” to exit.

2. Connect the computer to the main unit with a USB data cable, and turn on the power of the main unit. The computer will automatically find the new hardware and prompt that the hardware is installed and ready for use.

3. When you open the PC control software, it will automatically search for the USB and connect to the main unit. After connection, the connection button in the upper right corner will turn green and display “Connected”, indicating that the software and the main unit have been successfully connected. Now you can operate the main unit through the software. When exiting, click the “Connected” button first, and then close the software interface window.

PC Software Interface Instructions:

1. Menu Bar:
   It can conduct operations of uploading and downloading the whole machine data, saving and calling a single preset file, connecting the main unit, operating panel lock, selecting work status, selecting recommended effect value, and switching between Chinese interface and English interface.

2. Connection Button:
   One-button connection with green light meaning “Connected” and blue light meaning “Disconnected”.

3. Parameter Adjustment Area:
   Conduct detailed parameter setting to the required channel function.

4. Preset Operation Area:
   A single preset can be saved and called, and the preset saved and called are in the main unit.

5. Mute Button:
   You can mute and unmute all music and microphones with this button.

PC Software Operation Instructions
Volume Control Interface:

1. Display the current PEQ curve status of music, microphone and effect.
2. Audio source selection: VOD, OPT, COAX, BT.
3. You can adjust the limiter parameters as well as the volumes of music, microphone, and effect.

Music Processing Interface

1. The adjustment area of PEQ curve: Adjust the frequency and gain parameters by dragging the frequency point (small dot), and change the frequency of the low cut point by dragging the small square. Click “Show all EQ parameters” to display the frequency, gain, and bandwidth parameters of all PEQ points, and click “EQ reset” to restore all PEQ parameters to factory default.
2. The display area of PEQ parameters: You can manually input data to change the frequency, Q value and gain of the corresponding frequency point. Filter types (low shelf, high shelf, low cut, high cut) and bypass function keys are available.
3. The PEQ parameter slider can change the currently selected PEQ parameters (frequency, bandwidth, gain).
4. The volumes of VOD and SPDIF inputs can be changed.5. The noise gate function of music input can be turned on and off.
5. The volume of music can be controlled.

Microphone Processing Interface

1. The adjustment area of PEQ curve: Adjust the frequency and gain parameters by dragging the frequency point (small dot), and change the frequency of the low cut point by dragging the small square. Click “Show all EQ parameters” to display the frequency, gain, and bandwidth parameters of all PEQ points, and click “EQ reset” to restore all PEQ parameters to factory default.
2. The display area of PEQ parameters: You can manually input data to change the frequency, Q value and gain of the corresponding frequency point. Filter types (low shelf, high shelf, low cut, high cut) and bypass function keys are available.
3. The PEQ parameter slider can change the currently selected PEQ parameters (frequency, bandwidth, gain).
4. The low-cut frequency of the microphone can be adjusted. The low-cut filter types of BUTTERWORTH-6dB–24dB/ BESSEL-6dB–24dB/LINK-12dB–24dB and a bypass function key are available.
5. There are six levels of feedback suppression. Press the “Off” button to turn off the feedback suppression function.
6. The independent input volumes of 4 microphones can be adjusted.
7. The noise gate function of MIC input can be turned on and off. 8. The total MIC volume can be controlled and handled accordingly.

Effect Processing Interface

1. Independent processing of the PEQ parameters of echo and reverb: Adjust the frequency and gain parameters by dragging the frequency point (small dot). Click “Show all EQ parameters” to display the frequency, gain, and bandwidth parameters of all PEQ points, and click “EQ reset” to restore all PEQ parameters to factory default.
2. The display area of PEQ parameters: You can manually input data to change the frequency, Q value and gain of the corresponding frequency point. Filter types (low shelf, high shelf, low cut, high cut) and bypass function keys are available.
3. The PEQ parameter slider can change the currently selected PEQ parameters (frequency, bandwidth, gain).
4. There are mono and stereo options for echo. Mono and stereo are two different echo effects. In the mono state, only one delay and one repetition parameter can be adjusted; in the stereo state, the left and right delay and repetition parameters can be adjusted separately, so is the pre-delay of echo.
5. The volume, time, pre-delay, space, high cut and low cut of the reverb can be adjusted. 6. The direct sound parameters of the effect can be adjusted. 7. The total effect volume can be controlled.

Center Output Interface

1. The adjustment area of PEQ curve: Adjust the frequency and gain parameters by dragging the frequency point (small dot). Click “Show all EQ parameters” to display the frequency, gain, and bandwidth parameters of all PEQ points, and click “EQ reset” to restore all PEQ parameters to factory default.
2. The display area of PEQ parameters: You can manually input data to change the frequency, Q value and gain of the corresponding frequency point. Filter types (low shelf, high shelf, low cut, high cut) and bypass function keys are available.
3. The PEQ parameter slider can change the currently selected PEQ parameters (frequency, bandwidth, gain).
4. The low-cut frequency and slope of the center output are adjustable, and there is a bypass function key.
5. The center delay is adjusted in the range of 0-100ms.6. The threshold value of the compressor is adjustable. Click the “Set” button to set the ratio, start time and recovery time.
6. The volume of the center output is independently controllable, so are the phase and mute functions.

Bass Output Processing Interface

1. The adjustment area of PEQ curve: Adjust the frequency and gain parameters by dragging the frequency point (small dot), and change the frequency of the low cut point by dragging the small square. Click “Show all EQ parameters” to display the frequency, gain, and bandwidth parameters of all PEQ points, and click “EQ reset” to restore all PEQ parameters to factory default.
2. The display area of PEQ parameters: You can manually input data to change the frequency, Q value and gain of the corresponding frequency point. Filter types (low shelf, high shelf, low cut, high cut) and bypass function keys are available.
3. The PEQ parameter slider can change the currently selected PEQ parameters (frequency, bandwidth, gain).
4. The low-cut frequency of the subwoofer can be adjusted in the range of 20Hz-500Hz. Lowcut filter types include BUTTERWORTH -6–24dB/BESSEL-6dB–24dB/LINK-12dB–24dB, and there is a bypass function key.
5. The high-cut frequency of the subwoofer can be adjusted in the range of 20Hz-500Hz. High-cut filter types include BUTTERWORTH-6dB–24dB /BESSEL-6dB–24dB/LINK-12dB-24dB.
6. The delay parameter of the subwoofer output can be adjusted separately in the range of 0100ms.
7. The threshold value of the compressor is adjustable. Click the “Set” button to set the ratio, start time and recovery time.
8. The volume of the bass output is independently controllable, so are the phase and mute functions.

Specifications

Wireless MIC Specifications

• Frequency Range: 470-960MHz
• Frequency Response: 50Hz-16KHz
• Number of Adjustable Channels: 200
• Oscillation Mode: PLL digital phase-locked loop multi-channel frequency synthesis
• Frequency Stability: ±5ppm
• Modulation Method: broadband FM
• RF Power: high power: 30Mw; low power: 10mW
• Distortion: ≤0.3%
• Power Consumption: high power 120mA; low power 100mA@3V
• Maximum Frequency Deviation: ±50KHz
• Spurious Suppression: 80dBu
• Pilot Frequency: 30kHz/30.72kHz
• Operating Range: 50m

Power Specifications

• 4Ω Input Power: 750Wx2
• 8Ω Input Power: 450Wx2
• THD: <0.02%
• Frequency Response: 20Hz-20kHz, +/-1dB
• Input Impedance: 10k
• Input Sensitivity: 0dB
• S/N Ratio (20Hz-20KHz, 4Ohms): >100 dB
• Channel Separation (1KHz, 4Ohms): >70dB
• Damping Factor (10-400Hz, 8Ohms): >300
• Output Stage: Class D
• Protection: short circuit, DC output, overheating, overload
• Startup Delay: 1S
• Output Socket: red and black banana socket
• Other Specifications
• Power Supply: AC 220V 50Hz
• Weight (Net): 6.6Kg
• Dimensions (WXDXH): 438X350X88mm

DSP Specifications

• Frequency Response: 20Hz-20kHz, -0.5dB
• S/N Ratio: >105dBu
• Distortion: <0.01% at 1kHz (0dBu)
• Crosstalk: >70dBu, 20Hz-20kHz
• MIC Input Jack: unbalanced 6.3mm JACK
• MIC Max Gain: 30dBu
• MIC Input Impedance: 2KΩ
• Music Input Jack: unbalanced RCA
• Music Input Level: +12dBu
• Music Input Impedance: 1MΩ/Stereo
• Bluetooth Input: Bluetooth 5.0, Class2 4dbM frequency: 2.4G
• Fiber Input: 24bit 48KHz
• Coaxial Input: 75Ω
• Front Output Port: 1 set of balanced XLR, 1 set of unbalanced RCA
• Front Output Level: +12dBU
• Front Output Impedance: <500Ω
• Digital Processing: 32-bit DSP, 48kHz sampling rate, 24-bit sigma-delta A/D, D/A conversion
• Display: 5″ TFT with touch control 480×854 (RGB)
• Note: The data is tested by Takstar Laboratory, and Takstar has the final interpretation right!

Product Dimensions Diagram

Safety Precautions

** The lightning bolt with an arrow in the triangle is intended to warn users that there is a non-insulated “dangerous voltage” inside the product strong enough to cause electric shock.
The exclamation mark in the triangle is intended to show users important instructions related to the operation and maintenance (repair) of the product.
Warning: Risk of electric shock-do not open!
Warning: To avoid the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. When maintenance is needed, please contact the designated professional personnel.
Warning: To avoid the risk of electric shock or fire, do not place the product in rain or damp places. Do not place objects filled with liquids, such as vases, on the product. Before using this product, please read the safety instructions in this manual carefully.
Protect the ground terminal**. The equipment should be connected to a power socket with earthing protection.

Safety Instructions

To avoid possible personal injury or property damage caused by electric shock, high temperature, fire, radiation, explosion, mechanical hazards, and improper use, please read and observe the following items before using the product.

1. When using the product, please confirm whether the power of the connected device matches the power of the product, and adjust the volume of the device. Do not use it for a long time when the power of the product is exceeded or at a high volume to avoid product failure and hearing damage.
2. If there is any abnormality (such as smoke, odor, etc.) during use, please turn off the power switch and unplug the power plug immediately, and then send the product to the dealer for maintenance.
3. The product and accessories should be placed indoors in a dry and ventilated place. Do not store them in a humid and dusty environment for a long time. Avoid getting close to fire, rain, water, excessive collision, throwing, vibrating the machine and covering the ventilation holes during use, so as not to damage its function.
4. If the product needs to be fixed on the wall or ceiling, please make sure to fix it in place to prevent it from falling.
5. When using the product, you must abide by the relevant safety regulations. Please do not operate the product on occasions that are prohibited by laws and regulations to avoid accidents.
6. Please do not disassemble, refit, or repair the product by yourself to prevent personal injury. If you have any questions or service needs, please contact the local dealer.

Only suitable for use in areas below 2000m 2000 meters above sea level
Only suitable for use in non-tropical climates

Scan for more product informationhttp://www.takstar.com/

Guangdong Takstar Electronic Co., Ltd.
Address: No. 2 Fu KangYiRd.
Longxi Boluo Huizhou, Guangdong 516121 China
Tel: 86 752 6383644
Fax: 86 752 6383952
Email: sales@takstar.com
Website: www.takstancom

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>