TAKSTAR E126W Portable Wireless Amplifier User Manual

PORTABLE WIRELESS AMPLIFIER
E126W

Preface
Dear Customer,
Thank you for purchasing Takstar E126W Portable Wireless Amplifier. In order to better understand and use the product, please read this manual carefully. If you have any questions or suggestions, please contact our local dealer.

Features

• Compact, lightweight, wireless voice amplifier.
• UHF transmission, effective up to 40m in open areas.
• 8W high-power digital audio amplification, with a wireless headset mic.
• Built-in Li-ion battery lasts up to 8h, and supports Type-C quick charge.
• Wireless audio playback for untethered music enjoyment.
• LED indicators give you a clear idea about the device’s status.
• Wear across the shoulder or around the waist, use at ease.
• Stylish look and ergonomic design.

Product Content

Applications
Voice amplification for teaching, promotion, tour guide, training, sales.

Specifications

Headset Microphone

Note: The above data is measured by Takstar laboratory, and Takstar has the final interpretation right!

Function Descriptions

Voice Amplifier

1. Power Switch: slide the knob towards “ON” until you hear a “click” to power up the device into voice amplification mode, indicated by the lit blue power indicator. Keep sliding towards “ON” to increase volume, or vice versa, towards “OFF” to decrease volume or power off the device (slide until a “click” sound).
2. Power Indicator: illuminates red during charge; turns blue when fully charged; flashes red when the battery is running low during operation which requires charging the amplifier timely. (Recommended to power off the amplifier while charging)
3. MIC IN Jack: accepts ø3.5mm headphone plug for wired operation. (When the wired mic is inserted, the wireless mic will stop working.)
4. “M” Button: when powered on, press to switch between Bluetooth Mode and Microphone Mode, indicated by the respective voice prompt.
5. Charging Port: accepts Type-C charging cable for charging the amplifier.
6. Strap Clip: used to install a strap for wearing the amplifier across the shoulder.
7. Belt Clip: used to clip the amplifier onto the belt or pants.

Headset Microphone

1. Power Switch: slide towards “ON” to power up the device, indicated by the lit blue power indicator; slide towards “OFF” to turn off the device, indicated by the power indicator going off.
2. “M” Button: press and hold the “M” button to sync frequency; press “M” shortly to change frequency. (Refer to “Frequency Sync” in Operation Instructions)
3. Volume Control: press “+” once to increase microphone volume, or “−” once to decrease it.
4. Sync/Power Indicator: when powered up, this indicator is off when the headset microphone is out of battery; flashes blue when the microphone is low on battery. It also flashes blue during frequency sync after you press and hold “M”, or during frequency change, after you press “M” once.
5. Charging Indicator: illuminates red during charge, and goes off when fully charged.
6. Charging Port: accepts a Micro USB charging cable for charging the microphone.

Operation Instructions

I. Frequency Sync

1.  Sync Frequency
   The product is synced by default before shipping out the factory, and will automatically connect to each other without extra sync operation. In case of signal interference, you can re-sync or change the frequency following the below steps.
   First, turn on the headset microphone. When the blue mic LED is lit, press and hold the “M” button on the mic for 3s until the blue LED blinks. Then immediately turn on the amplifier, wait till the mic LED stops blinking and stays lit, and speak to the microphone. If synced successfully, you should hear your voice from the amplifier.
   If you cannot hear your voice from the amplifier when speaking to the microphone, please retry the above-syncing step.

2. Change Frequency Turn on both the amplifier and the headset microphone, and press the “M” button on the mic shortly to change frequency, in which case the blue LED will flash

3. times and then stay lit, indicating successful auto sync. 3. Use Multiple Voice Amplifiers Simultaneously
   ① Follow the above Sync Frequency steps to re-sync each device, then o the following frequency changes.
   ② Press the “M” button once on 1st mic to change frequency, then press “M” twice on the 2nd mic to change frequency as well, triple times on the rd mic, such so forth until the final device. Be sure to proceed in the aforementioned order.
   II. Bluetooth Pairing Upon first time using the device, you need to connect it to your phone or Bluetooth device as follows:
   ① Turn on the amplifier, then press the “M”  button once to switch to Bluetooth Mode and start Bluetooth discovery and pairing, indicated by a flashing blue LED.
   ② Enter the Settings menu on your phone, find and enable Bluetooth, wait until “TAKSTAR E126W” is discovered, and tap on it to connect. When paired successfully, the LED will resume lit permanently, and there will be a  voice prompt “Bluetooth Connected”. Devices such as cell phones, laptops, tablets, and iPads can play music after a successful Bluetooth connection with the product.
   ③ At our next power-up, simply press the “M” button to enable Bluetooth and auto-connect to the previously paired device, signaled by a voice prompt “Bluetooth Connected”.  hen Bluetooth is connected, press “M” once to disconnect, followed by a voice prompt “Microphone Mode”.

Safety Instructions

To avoid electric shock, overheating, fire, radiation, explosion, mechanical risk, and injury or property loss due to improper use, please read and observe the following items before  use:

1. Please check if the power of the connected equipment matches that of this product before operation. Adjust the volume to the proper level during operation.
   Do not operate at over-power or high-volume levels for an extended time to avoid product malfunction or hearing impairment.

2. If there is any abnormality during use (e.g., smoke, strange odor), please kill the power switch and unplug it from the power source, then send the product to the local dealer for repair.

3. When using a power adapter to supply power, please use a matching power adapter that has obtained CCC certification and meets the standard requirements.

4. Do not dissemble, impact or squeeze the product or throw it into the fire. Stop using if it is severely swollen.
   Do not place in a high-temperature environment.
   Do not use it after the battery is submerged in water. Risk of explosion if the battery is replaced with the wrong model. Be sure to dispose of used batteries following instructions.

5. Keep this product and its accessories in a dry and ventilated area.
   Do not store in a humid or dusty area for an extended time. Keep away from fire, rain, liquid intrusion,  bumping, throwing, vibrating, or from blocking any ventilation openings, to prevent malfunction.

6. The product must, when installed on walls or ceilings, be fixed firmly in place at adequate strength to prevent from falling.

7.  Please abide by safety rules during operation. Do not use the product in places prohibited by laws or regulations to avoid accidents.

8. Do not disassemble or repair the product by yourself to avoid injury. If you have any questions or require any services, please contact our local dealer.

http://www.takstar.com/
Guangdong Takstar Electronic Co., Ltd.
Address: No. 2 Fu Kang YiRd., Longxi Boluo
Huizhou, Guangdong 516121 China
Tel: 86 752 6383644 Fax: 86 752 6383952
Email:sales@takstar.com
Website:www.takstar.coom

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>