LINDY DisplayPort to Dual HDMI MST Hub 38409 User Manual

: June 6, 2024
: LINDY

Table of Contents

Introduction
Package Contents
Features
Operation
CE/FCC Statement
Recycling Information
Documents / Resources

LINDY DisplayPort to Dual HDMI MST Hub 38409

Introduction

Thank you for purchasing the LINDY 2 Port DisplayPort Splitter with Expander- view. This device is a high performance DisplayPort splitter which allows one DisplayPort source to be shown simultaneously on 2 different HDMI or DVI displays. The signal can also be extended across 2 or 4 displays to show one picture if your source device has more than one output port. The Expander-view function detects how many displays are connected and generates a combined resolution EDID that allows the picture to be extended across 2 or 4 displays.

To use this features the graphics card should be DP 1.2 version or have MST (DP Multi Stream Transport) support or support AMD Eyefinity, Nvidia Surround or Intel Collage.

Package Contents

2 Port DP Splitter with Expander-view
USB Charging Cable
This manual

Features

Supports DisplayPort 1.2 signals up to 3840×2160@60Hz
We recommended you use identical monitors for the best performance
Supports cable lengths of 5m in and 5m out
Maximum resolution depending on the monitors:
○ Clone Mode:
Max. 3840×2160@30Hz or 1920×1080@60Hz or 1920×1200@60Hz up to 2 displays
○ Expander Mode:
¤ 3840×1080@60Hz with 2 displays (2 x 1920×1080) or 3840×1200@60Hz with 2 displays (2 x 1920×1200)
¤ 3840×2160@60Hz with 4 displays (4 x 1920×1080) using 2 products No.38409 *

Operation

The LINDY 2 port DisplayPort splitter is a plug and play device that does not need to be configured with software or driver support. The splitter automatically switches between “clone” mode and “extended” mode by controlling the output resolution on the computers graphics card.

Before you install the splitter, make sure all your devices are switched off.

Connect a DP cable from your PC to the DP “in” port of the splitter.
Connect the DP splitter to the HDMI or DVI “in” port of your displays.
NOTE: We strongly suggest using monitors of the same resolution and size. If using monitors with different native resolutions, connect the monitor with the lowest resolution to port 1. Otherwise the screen may remain blank and not work at all.
Power on the computer and then the displays. The splitter may be powered from the DP port. If the DP port cannot provide enough power connect the supplied USB DC cable to an available USB port or to a USB power supply.
If you don’t get a picture, reboot again. Please make sure that your graphics card supports MST (DP Multi Stream Transport) or AMD Eyefinity, Nvidia Surround or Intel Collage.
If this does not help, attach one monitor. If this does not work the monitor model may be incompatible and would need changing.
When you have a picture on your displays, adjust the resolution on your PC to the maximum supported for clone mode or the required resolution for multiple displays.

4 displays can be achieved using 2 products

CE/FCC Statement

CE Certification
LINDY declares that this equipment complies with relevant European CE requirements.

UKCA Certification
LINDY declares that this equipment complies with relevant UKCA requirements.

FCC Certification
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
You are cautioned that changes or modification not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation

Recycling Information

WEEE (Waste of Electrical and Electronic Equipment), Recycling of Electronic Products

Europe, United Kingdom
In 2006 the European Union introduced regulations (WEEE) for the collection and recycling of all waste electrical and electronic equipment. It is no longer allowable to simply throw away electrical and electronic equipment. Instead, these products must enter the recycling process.
Each individual EU member state, as well as the UK, has implemented the WEEE regulations into national law in slightly different ways. Please follow your national law when you want to dispose of any electrical or electronic products. More details can be obtained from your national WEEE recycling agency.

Tested to comply with
FCC standards.
For home and office use.

Hersteller I Manufacturer (EU):.
LINDY-Elektronik GmbH Markircher Str. 20 68229 Mannheim Germany
Email:info@lindy.com , T: +49 (0)621 470050

Manufacturer (UK):
LINDY Electronics Ltd Sadler Forster Way Stockton-on-Tees, TS17 9JY England
Emailsales@lindy.co.uk, T: +44 (0)1642 754000

lindy.com