LINDY 38139 70m C6 HDBaseT HDMI 10.2G and IR Extender with PoC User Manual
- June 6, 2024
- LINDY
Table of Contents
70m C6 HDBaseT HDMI 10.2G and IR Extender with PoC -IR Emitter
User Manual
No. 38139
lindy.com
!!! IMPORTANT !!!
Only use a direct Cat.5e/6/7 cable connection between the HDBaseT ports. Do
not connect these ports to the Network or Ethernet equipment or any active
components
**Safety Instructions
**
! WARNING!
Please read the following safety information carefully and always keep this
document with the product. Failure to follow these precautions can result in
serious injuries or death from electric shock, fire, or damage to the product.
Touching the internal components or a damaged cable may cause electric shock,
which may result in death. This device is a switching type power supply and
can work with supply voltages in the range 100 – 240 VAC For worldwide
usability four different AC adapters are enclosed: Euro type, UK type,
US/Japan type, and Australia/New Zealand type. Use the appropriate AC adapter
as shown in the picture and ensure it
is firmly secured in place and does not detach by pulling before installing it
into a power socket. To reduce risk of fire, electric shocks, or damage:
- Do not open the product nor its power supply. There are no user-serviceable parts inside.
- Only qualified servicing personnel may carry out any repairs or maintenance.
- Never use damaged cables.
- Do not expose the product to water or places of moisture.
- Do not use this product outdoors it is intended for indoor use only.
- Do not place the product near direct heat sources. Always place it in a well-ventilated place.
- Do not place heavy items on the product or the cables.
- Please ensure any adapters are firmly secured and locked in place before inserting into a wall socket
Instructions for Use of Power Supply
To connect the adapter
Slide the desired plug adapter into the power supply and rotate clockwise
until it locks into place.
To remove the adapter
Press the push button latch.
While pressed, rotate the adapter anticlockwise.
Introduction
Thank you for purchasing the LINDY C6 HDMI Extender with HDBaseT TM
Technology. It supports uncompressed HDMI signal transmission for resolutions
up to Ultra HD 4K 60Hz, making it ideal for use in Home Cinema, Professional
AV, and Digital Signage applications. In addition to extending HDMI signals,
the Extender also supports the extension of bi-directional IR signals,
allowing you to control connected AV equipment such as a source or display
from either end of the installation.
For added convenience, the Extender also supports Power-over-HDBaseT (PoH)
which allows the Transmitter and Receiver units to be powered from a single
power supply, giving greater flexibility and making the Extender ideal for
discreet and retrofit installations.
Please Note: The quoted lengths and resolutions are possible with a
direct connection between Transmitter and Receiver using good quality Cat.6
solid core cable. Using a different cable type, or introducing wall plates,
couplers, or patch panels will result in a reduction of possible distances.
Package Contents
- HDMI Extender C6 for HDMI (1 x Transmitter, 1 x Receiver)
- Multi-Country Power Adapter (24V DC/1A) x 1
- IR Extender Cable 1.4m x 4 (2 x Emitter, 2 x Receiver)
- Mounting Brackets with screws x 4
- This User Manual
Features
- Extends HDMI & IR signals up to 70m via its HDBaseT connection
- Supports resolutions up to Ultra HD 4K 60Hz including Full HD 1080p 3D
- Power over HDBaseT allows a single power supply to power the Transmitter and Receiver
- Bi-directional IR control of AV display and source equipment
- Suitable for use with 3D/HDTV Home Theatre, professional HDTV installations, Computer Systems, Multimedia, and Control Centre system installations.
Specification
-
Maximum cable length for the HDBaseT connection: 70m (approx.)
-
Supports resolutions up to:
• Full HD 1080p 60Hz (4:4:4 up to 16bpc) including 3D up to 70m
•Ultra HD 4K 60Hz (4:2:0 12bpc) / 4K 24/30Hz (4:4:4 8bpc) up to 40m -
Support for HDCP 2.2/1.4, CEC, and Lip Sync pass-through
-
Audio Pass-through: LPCM 7.1 audio, Dolby® TrueHD, Dolby Digital® Plus, and DTS-HD Master Audio™
-
IR Extension cables (included) can be attached to allow the bi-directional control of IR (30 – 60kHz) equipment via the extender
-
Maximum HDMI Cable length, 2m in/out
-
Power over HDBaseT (PoH)
-
Dimensions: 100 x 65 x 25mm (L x W x H) ; Weight: ~0.200 kg (each unit) HDBaseT™ and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.
Important! Before starting the installation, please ensure that all devices are powered off.
|
---|---
The following steps are for an installation using HDMI equipment, if you are using DVI equipment, please substitute the HDMI cables for DVI to HDMI cables where required.
- Connect your HDMI source to the HDMI Extender Transmitter unit using an HDMI cable (maximum length 2m).
- Connect one end of the Cat.5e/6/7 cable (max. length 70m) to the HDBaseT port on the Transmitter and the other end to the HDBaseT port of the Receiver. Use solid core installation cable of at least Cat.5e UTP.
- Use another HDMI cable (maximum length 2m) to connect your HDMI display device to the HDMI output port on the Receiver unit.
- For additional Infrared remote signal functionality, connect the included IR Emitter cables to the IR OUT ports and the IR Receiver Cables to the IR IN ports on both the Transmitter and Receiver units.
- The IR Emitters should be placed in front of the IR receiver of the devices which are to be controlled. The IR Receivers should be located where they may easily receive the signal of your IR remote.
- Plug the DC power supply into the Transmitter and switch it on.
- Power on your HDMI Source and Display to complete the installation.
**Troubleshooting
**
There is no display on the screen.
- Check that the DC plug and jack used by the external power supply is firmly connected and screwed on securely
- Check that the Cat.5e/6/7 cable is plugged in correctly and that the Link Status LED is lit.
- Check that the HDMI source and display are both powered on and active
- Power off all the devices, then power on in this order: first, the transmitter unit, then the display, and finally the source. For several HDMI devices, it may be helpful to unplug and replug their HDMI connection to re-initiate the HDMI handshake and recognition.
- Reduce the length of Cat.5e/6/7 or HDMI cable used, or use a higher quality cable.
General Guidelines
- If you are terminating the Cat.5e/6/7 yourself, ensure that you untwist less than 13mm of cable to make the connection; otherwise, you may introduce cross-talk which will affect the performance of the Extender.
- Do not twist, kink, or over-extend the Cat.5e/6/7 cable, and ensure that its minimum bend radius is observed (usually, this is 4 x the outer dimension of the cable).
- Do not use excessive force when pulling the cable.
CE/FCC Statement
CE Certification
LINDY declares that this equipment complies with relevant European CE
requirements.
FCC Certification
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
You are cautioned that changes or modifications not expressly approved by the
party responsible for compliance could void your authority to operate the
equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
The enclosed power supply has passed Safety test requirements, conforming to the US American versions of the International Standard IEC 60950-1 or 60065 or 62368-1.
Hersteller / Manufacturer (EU):
LINDY-Elektronik GmbH
Markircher Str. 20
68229 Mannheim
Germany
Email: info@lindy.com , T: +49 (0)621 470050
Manufacturer (UK):
LINDY Electronics Ltd
Sadler Forster Way
Stockton-on-Tees, TS17 9JY
England
sales@lindy.co.uk, T: +44 (0)1642 754000
Recycling Information
WEEE (Waste of Electrical and Electronic Equipment), Recycling of
Electronic Products
Europe, United Kingdom
In 2006 the European Union introduced regulations (WEEE) for the collection
and recycling of all waste electrical and electronic equipment. It is no
longer allowable to simply throw away electrical and electronic equipment.
Instead, these products must enter the recycling process.
Each individual EU member state has implemented the WEEE regulations into
national law in slightly different ways. Please follow your national law when
you want to dispose of any electrical or electronic products. More details can
be obtained from your national WEEE recycling agency.
Tested to comply with
FCC Standards
For Home and Office Use!
No. 38139
4th Edition, January 2021
lindy.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>