SMARTRO Wireless Weather Station SC93 Instruction Manual
- June 6, 2024
- SMARTRO
Table of Contents
Wireless Weather Station SC93
Instruction Manual
WIRELESS WEATHER STATION Model: SC93
Time
Moon Phase
In & Out Temp
In & Out Humidity
Dual Alarm
Weather Forecast
°C/°F Selectable
Snooze
Content
1. Preface……………………………………………………………………………..1 2.
Attention……………………………………………………………………………1 3. Package
Content………………………………………………………………..2 4. Product
Specification………………………………………………………….2
4.1 Color Weather Station……………………………………………………..2 4.2 Wireless Remote
Sensor………………………………………………….3 5. Know Your Device………………………………………………………………5 5.1
Screen…………………………………………………………………………..5 5.2 Main
Unit……………………………………………………………………….6 5.3 Wireless Remote
Sensor………………………………………………….7 6. Preparation……………………………………………………………………….8 7.
Initial Time Setup………………………………………………………………..9 8. Dual Alarm
Setting…………………………………………………………….10 8.1 How to Check Your
Alarms……………………………………………..10 8.2 Activate/Deactivate the Alarm
Function…………………………….10 8.3 Manual Setting of the Alarms…………………………………………..10
8.4 Turn off the Alarm Tone………………………………………………….11 8.5 Snooze
Function……………………………………………………………11 9. Weather Station and Remote Sensor Pairing
& Manual Signal Reception..12 9.1 Weather Station and Remote Sensor
Pairing…………………….12 9.2 Loop Mode…………………………………………………………………..13 9.3 Manual
Signal Reception………………………………………………..14 10. Temperature &
Humidity…………………………………………………..15 10.1 °C/°F Selection……………………………………………………………15
10.2 How to Set Temperature & Humidity Alert……………………….15 10.3 Temperature &
Humidity Trend………………………………………17 10.4 How to Check Maximum/Minimum
Temperature/Humidity…17 11. Weather Forecast……………………………………………………………18 11.1
Weather Forecast Statement…………………………………………18 11.2 The Symbols of Weather
Forecast………………………………….18 12. Moon Phase…………………………………………………………………..19 13. Air
Pressure……………………………………………………………………19 13.1 Air Pressure Trend
Display……………………………………………19 13.2 How to Check Air Pressure
History…………………………………19 14. Backlight……………………………………………………………………….20 15.
Troubleshooting……………………………………………………………..21 16. After-sales
Support………………………………………………………….23 17. Waste Disposal………………………………………………………………24
1. Preface
Thank you for choosing this device from SMARTRO.
Before You Start Using It
Make sure to read the instruction manual carefully. This information
will help you to familiarize yourself with your new device, to learn all of
its functions and get advice in the event of problems.
Following the instructions will prevent damage to your device. We shall not be
liable for any damage that occurs as a result of
not-following of these instructions.
Please keep this instruction manual for future reference.
2. Attention
Please follow the instructions for operation. Please use the original or
manufacturer specified attachments or
accessories.
Do not disassemble the product, so as to avoid safety hazards. Do not place
any items on top of the product that may damage
the product.
Do not place the product near water source or in a damp place. Please
terminate use immediately upon damage, which is
caused as a result of improper use or repair by a non-factory approved
technician.
1
Do not place the product in places that are exposed to direct
sunlight and high temperature such as radiator, electric heater, stove, etc.
Keep the product away from strong electromagnetic waves,
strong static electricity, or moisture and condensation.
Children below 10 years of age should be supervised by an
adult, if/when using this product.
Clean your device with a soft damp cloth. Do not use solvents or
scouring agents.
3. Package Content
Color Weather Station1 Wireless Remote Sensor1 DC Power Adapter1
Instruction Manual1
4. Product Specification
4.1 Color Weather Station
Tabletop stand/ wall mount Weather forecast Indoor & outdoor temperature
Indoor temperature measurement range: 0°C(32°F) ~ +50°C (122°F)
2
Outdoor temperature measurement range: -40°C (-40°F) ~ +70°C
(158°F)
Indoor humidity measurement range: 1%RH~99%RH Barometric pressure Maximum &
minimum records Dual alarm with snooze function Air pressure trend
Temperature/ humidity alert Moon phase Alternative 12/24 hour format Calendar
°C/°F switchable Adjustable backlight display Low battery indicator Power
supply:
Battery: 2 x AA batteries (not included)
DC power adapter: 5V 500mA
4.2 Wireless Remote Sensor
Tabletop stand/ wall mount/ hanging hole 3 channels available Low battery
indicator °C/°F switchable Power supply: 2 x AA batteries (not included) Range
of transmission: 200 feet in open area
3
Outdoor temperature measurement range: -40°C (-40°F) ~
+70°C (158°F)
Outdoor humidity measurement range: 1%RH~99%RH
4
5. Know Your Device
5.1 Screen
A1: Weather forecast A2: Air pressure A3: Time A4: Indoor temperature and
humidity A5: Outdoor temperature and humidity A6: Moon phase icon A7: Date A8:
Temperature alert A9: Humidity alert A10: Dual alarm
5
5.2 Main Unit
B1: SNOOZE/LIGHT B2: Button
: Time setting (long press 2s to set) : Alarm setting (long press 2s to set)
PRESSURE: review history record : For setup preferences : For setup
preferences
: Maximum/ Minimum values : Switch channel B3: Alarm switch B4: Temperature/humidity alert B5: Sensor B6: Battery compartment B7: Fold-out tabletop stand B8: Power supply socket B9: Wall-mount hole
: Select temperature unit
6
5.3 Wireless Remote Sensor
C1: Temperature C2: Humidity C3: Transmission signal light C4: “°C/°F” button
C5: “TX” button C6: Channel switch knob C7: Battery compartment C8: Hanging
hole C9: Wall-mount hole
7
6. Preparation
Open weather station battery compartment cover, insert 2 x
AA batteries, ensure correct battery polarities [ “+” and “” ]. And connect
the DC adapter to power the weather station.
The screen will light up, and the device will make a beeping
sound. The weather station starts to detect indoor temperature and humidity.
The receiver will start to make a connection with the outdoor
remote sensor, a reception RF antenna symbol in the “OUT” display area will
flicker on the screen. This procedure will takes 3 minutes at most.
Open the wireless remote sensor battery compartment cover.
Choose a same channel as the weather station. Insert 2 x AA batteries, ensure
correct battery polarities [ “+” and “” ].
After the unit has made a connection with the outdoor remote
sensor, the detected temperature and humidity will display on the screen.
For specific pairing operation of the weather station and remote
sensor, please refer to 9.1 Weather Station and Remote Sensor Pairing on page
12.
8
7. Initial Time Setup
Long press ” ” key for two seconds. The year display “2020” starts to flash.
Press “” or “” to set
the correct year.
Press ” ” to confirm your setting. The month display starts to flash. Press “”
or “” to set the
correct month.
Press ” ” to confirm your setting. The date display starts to flash. Press “”
or “” to set the
correct date.
Press ” ” to confirm your setting. “M” and “D” will be flashing, press “” or
“” to set the date
display to Month/Date or Date/Month.
Press ” ” to confirm your setting. The time displays either in 12 or 24 hour
format. Press “” or
“” to choose 12hr or 24hr.
Press ” ” to confirm your setting. The hour display starts to flash. Press “”
or “” to set the
correct hour.
Press ” ” to confirm your setting. The minute display starts to flash. Press
“” or “” to set the
correct minute.
Press ” ” to confirm your setting. The weather icon display starts to flash.
Press “” or “” to set
the weather of the day. Please set the weather icon according to
9
the real-time weather condition outside.
Press ” ” to confirm your setting and complete the setup.
Note: During the setup, if there is no operation of buttons within 20 seconds,
the weather station will save the current setting and automatically return to
normal display from manual setting mode.
8. Dual Alarm Setting
8.1 How to Check Your Alarms Press ” ” key. Press 1x: Display time of alarm 1
Press 2x: Display time of alarm 2 Press 3x: Display current time
8.2 Activate/Deactivate the Alarm Function
When the switch of alarm 1 or alarm 2 on the back of the
weather station is moved to “ON” position, the symbol ” ” or ” ” will appear
on the screen. The alarm function is activated.
When the switch of alarm 1 or alarm 2 on the back of the weather
station is moved to “OFF” position, the symbol ” ” or ” ” will disappear from
the screen. The alarm function is deactivated.
8.3 Manual Setting of the Alarms Please make sure the alarm switches are moved
to “ON” before manually setting the alarms.
10
Press and hold ” ” key for two seconds, the hour of alarm 1
starts to flash.
Press “” or “” keys to set the required hour. Press ” ” to confirm your
setting. The minute of alarm 1 starts to flash. Press “” or “” to set the
required minute.
Press ” ” to confirm your setting. The hour of alarm 2 starts to flash. Press
“” or “” to set the
required hour.
Press ” ” to confirm your setting. The minute of alarm 2 starts to flash.
Press “” or “” to set the
required minute.
Press ” ” to save and complete the setup.
8.4 Turn off the Alarm Tone The alarm will ring for 2 minutes, pressing any
button except “SNOOZE/LIGHT” will stop the tone. The alarm will repeat at the
same time the next day.
8.5 Snooze Function Proceed as follows to activate snooze function.
While the alarm is ringing, touch “SNOOZE/LIGHT” to activate
the snooze function. When the snooze function is activated, ” ” or ” ” will
keep flashing on the display. The alarm will ring again in 5 minutes.
11
When the snooze function is activated, press any button except
“SNOOZE/LIGHT” to exit the snooze mode.
If alarm 2 rings during the snooze mode of alarm 1, the snooze
function of alarm 1 will automatically be deactivated. Note: During the setup
of the alarms, if there is no operation of buttons within 20 seconds, the
weather station will save the current setting and automatically return to
normal display from manual setting mode.
9. Weather Station and Remote Sensor Pairing & Manual Signal Reception
9.1 Weather Station and Remote Sensor Pairing Weather station: –Connect the
weather station to power supply. –Select a channel that permanently displays
on the weather station. Press ” ” button to select CH1, CH2 or CH3. –After the
weather station is powered on, the RF signal icon
located on the upper left side of the “OUTDOOR” column will flash for 3
minutes. This indicates that the weather station is in synchronization mode
and waiting for the remote sensor to connect. –If the RF signal icon stops
flashing after 3 minutes, long press “SENSOR” button on the back of the
weather station to activate the weather station synchronization mode. The RF
signal icon will flash again.
12
Wireless Remote Sensor: –Select a same channel with the weather station for
the remote sensor. Open the battery compartment of the remote sensor to select
channel with numbered knobs (1, 2, and 3). –Insert 2 x AA batteries in the
remote sensor. The indicator will light up once to indicate that the wireless
remote sensor is sending out signals. Please ensure that the weather station
is in synchronization mode so that it can receive the signals sending from the
remote sensor. –When the weather station successfully receives signals from
the remote sensor, the temperature and humidity detected by the remote sensor
will display on “OUTDOOR” column of the weather station. –The weather station
can connect up to 3 wireless remote sensors at the same time. If multiple
sensors are used simultaneously, please repeat 9.1 Weather Station and Remote
Sensor Pairing to connect other remote sensors. Please make sure these sensors
are on different channels. –Press ” ” button on the weather station to view
the readings of each channel.
9.2 Loop Mode This mode is applicable in the event that multiple wireless
remote sensors are used simultaneously. — Press ” ” button on the weather
station until ” ” is displaying in the top left corner of outdoor temperature
area. In this mode, the
13
outdoor readings will display from CH1 to CH3 automatically every 5 seconds.
–To see the temperature and humidity on a fixed channel, just press ” ” button
until ” ” disappears. Once it disappears, the outdoor readings will stop
cycling.
9.3 Manual Signal Reception If there is no outdoor temperature showing on
weather station or there is no change in the temperature and humidity for a
long time, it indicates that the weather station fails to receive signals from
wireless remote sensor, please take the following operations: –Please ensure
that the channels of the weather station and sensor are same. –Long press
“SENSOR” button on the back of the weather station to receive signals
manually. A flashing RF antenna symbol will display beside the channel. This
means that the weather station is in a receiving state. –Press “TX” button on
wireless remote sensor to send out signals manually and a red light will
flash.
Note:
In the case of using only one sensor, when the channel of the
weather station is not same as the channel of the sensor, there would be no
outside temperature showing on the weather station.
The wireless sensor can be placed anywhere (indoor or outdoor)
you want to measure the temperature remotely.
14
If you want to measure the outdoor temperature, please place
the sensor outside away from direct sunlight and rain such as under eaves or
on a porch.
10. Temperature & Humidity
10.1 °C/°F Selection Weather station: Press “°C/°F” button on the weather
station to choose the temperature display unit. Sensor: Open the battery
compartment cover and press “°C/°F” button to choose the temperature display
unit on the sensor.
10.2 How to Set Temperature & Humidity Alert Press “ALERT” on the back of the
weather station to activate or deactivate the temperature and humidity alert.
The icon ” ” will appear or disappear on the screen. Choose the channel you
want to start setting the temperature and humidity alert as follows:
Long press “ALERT” until ” “and the outdoor temperature are
flashing. Press “” or “” to set the required maximum outdoor temperature.
Press ” ALERT” to confirm your setting.
When ” ” and the outdoor temperature are flashing, press “”
or “” to set the required minimum outdoor temperature. Press “ALERT” to
confirm your setting.
When ” ” and the outdoor humidity are flashing, press “”
15
or “” to set the required maximum outdoor humidity. Press “ALERT” to confirm
your setting.
When ” ” and the outdoor humidity are flashing, press “” or
“” to set the required minimum outdoor humidity. Press ” ALERT” to confirm
your setting.
When ” ” and the indoor temperature are flashing, press “”
or “” to set the required maximum indoor temperature. Press “ALERT” to confirm
your setting.
When ” ” and the indoor temperature are flashing, press “”
or “” to set the required minimum indoor temperature. Press “ALERT” to confirm
your setting.
When ” ” and the indoor humidity are flashing, press “” or
“” to set the required maximum indoor humidity. Press “ALERT” to confirm your
setting.
When ” ” and the indoor humidity are flashing, press “” or
“” to set the required minimum indoor humidity. Press “ALERT” to confirm your
setting.
If you want to set the alert values of the other 2 channels, please
press ” ” to change the channel and repeat the steps above.
When the temperature or humidity reaches the set value of
the alert, ” ” or ” ” and the temperature or humidity will start flashing and
a beep will arise for 5 seconds. Pressing any button can temporarily stop the
alarm, however ” ” or ” ” will still keep flashing on the screen. The alert
will restart in one minute unless it is deactivated or the temperature and
humidity return to the set
range. To completely end the alarm, please press “ALERT”.
16
Note:
The temperature and humidity alerts of 3 channels can be set
separately. If any channel reaches the set value of the alert, the main unit
will start ringing.
In any case, if ” ” is displaying on the screen and the alert
function is not needed, please press “ALERT” to clear it away. Otherwise, it
will ring at any time when reaching the set temperature or humidity set value.
To avoid disturbance at the night, please turn it off.
10.3 Temperature & Humidity Trend The weather station monitors the current
temperature and humidity change.
: The temperature/humidity is rising. : The temperature/humidity is falling.
: The temperature/humidity is remaining constant.
10.4 How to Check Maximum/Minimum Temperature/Humidity
To toggle indoor/outdoor maximum, minimum temperature and
humidity data, please press ” ” : Press once to show the maximum temperature
and humidity values. Press twice to show the minimum temperature and humidity
values. Press three times to return to the current temperature and humidity
values.
To reset the maximum and minimum temperature and humidity,
press ” ” to select maximum or minimum value, and long press the button for 2
seconds to clear the history maximum or minimum
17
values. At this time, “MAX” or “MIN” will disappear from the display screen.
If not checking the maximum or minimum values, long pressing
” ” can clear both of the history values.
Note:
If the temperature or humidity reading is below the ranges, LL.L
will appear. If the temperature or humidity reading is above the ranges, HH.H
will appear.
11. Weather Forecast
11.1 Weather Forecast Statement
The weather station calculates the weather forecast based on
the history recorded barometric pressure trend.
The weather forecast cannot be compared with the professional
weather services supported by satellites and high-performance computers. It
provides an approximate indication of current developments.
Please take the weather forecast from local weather station as
authoritative.
11.2 The Symbols of Weather Forecast
sunny thunder storm
snowy rainy 18
cloudy
slightly cloudy
12. Moon Phase
When the calender has been set, the weather station will display 8 different
moon phases: New moon, Waxing Crescent, First Quarter, Full Moon, Waning
Gibbous, Last Quarter, Waning Crescent, New Moon.
13. Air Pressure
13.1 Air Pressure Trend Display The weather station measures the current
relative air pressure. The current air pressure is compared with recorded air
pressure trends.
: The air pressure is rising. : The air pressure is falling.
: The air pressure is remaining constant.
13.2 How to Check Air Pressure History Press “PRESSURE” to display the
recorded air pressure values during the last 12 hours.
19
14. Backlight
–Connect the weather station with DC adapter, the backlight will always keep
on. The backlight has 3 brightness levels, BrightLow-Out for selection. To
adjust the backlight brightness, touch “SNOOZE/LIGHT” to choose a brightness
that is comfortable for you. –Any restart or power break will cause a loss of
the previous manual setting. In case of power failure, please insert 2 AA
batteries in the weather station to keep the memory of manual setting.
Note:
The power of the batteries is not enough to support such large
display. So it is not recommended to power the weather station only by
batteries.
When the weather station is only powered by batteries, touching
“SNOOZE/LIGHT” will temporarily activate the backlight for 10 seconds, then it
will be automatically off and enter into a power saving mode.
To keep the display stay on constantly, please connect the
weather station with DC adapter.
20
15. Troubleshooting
PROBLEM
CAUSE
SOLUTION
The weather station is only powered by batteries.
No backlight.
1. Press “SNOOZE/LIGHT” to temporarily activate the backlight for 10 seconds. 2. Connect DC adapter to power up the weather station, the backlight will remain on.
DC adapter is connected, but the backlight is set to “OUT” state.
Press “SNOOZE/LIGHT” to adjust the backlight brightness, out-medium-high.
The batteries of the Replace 2×AA new batteries sensor have run out. for the outdoor remote sensor.
The channel displaying on the No outdoor weather station temperature is different from displays on the channel of the the weather remote sensor. station.
Adjust the channel of the weather station or the sensor to keep them paired. Weather station: Press ” ” to select a channel. Sensor: Switch the knob “1 2 3” inside the battery bay to select a channel.
The weather station did not receive signals from the outdoor sensor.
1. Long press “SENSOR” on the back of the weather station to search signals again. 2. Press “TX” of sensor to send signals.
21
The remote sensors Keep the wireless sensor
are exposed to the away from direct sunlight and
sun or rain.
rain.
The outdoor
temperature on the weather station is There is a delay different from or interruption of that on the transmission. sensor.
1. Long press “SENSOR” on the back of the weather station. 2. Press “TX” of sensor to send signals. 3. Wait for several hours to see if the readings are close
or same.
If problem persists, please contact after-sales support at: support@smartro.co.
The indoor Temperature range
and outdoor in 50°F~104°F(10°C 1. The difference is in a
readings ~40°C), tolerance: normal range.
are different ±0.9°F.
2. If the difference is beyond
when putting Other: ±2.7°F.
the range, please please
the two
Humidity range in contact after-sales support at:
devices
30%~80%, tolerance: support@smartro.co.
together. ±3%. Other: ±5%.
The forecast displaying on the weather station is different from the real-time weather.
The weather station calculates the weather forecast for the next 12 hours based on the barometric pressure trend, which is not the current weather.
Please refer to the real-time weather.
22
The alarm
The time alarms function is activated.
Please check the set alarms and reset them or switch the alarms to “OFF”.
rings
The temperature
unexpectedly or humidity alert
at night.
is activated. The
temperature or
humidity have
reached alert range.
Reset the temperature or humidity alert range. Press “ALERT” on the back of the weather station to turn it off.
The outdoor readings display
The display was set to loop mode.
Press ” ” until the arrow icon disappear to cancel the loop mode.
occasionally If problem persists, please contact after-sales on the clock. support at: support@smartro.co.
16. After-sales Support
If your device fails to work despite these measures or your experience with us
was less than perfect in any way, please do not hesitate to contact us. For
more products, please visit our website: https://www.smartro.co/ For further
support and discount information, join our Facebook group or follow us on
Instagram.
: +1(323)287-5798 : support@smartro.co : http://bit.ly/smartro_01 : smartro_01
23
17. Waste Disposal
This product is manufactured with high-grade materials and
components which can be recycled and reused.
As a consumer, you are legally required to take them to your
retail store or an appropriate collection site depending on national or local
regulations in order to protect the environment.
The symbols for the heavy metals contained are: Cd=cadmium,
Hg=mercury, Pb=lead.
Please do not dispose of this instrument in household waste.
The user is obligated to take end-of-life devices to a designated collection
point for the disposal of electrical and electronic equipment, in order to
ensure environmentally-compatible disposal.
24
After-sales Support
: +1(323)287-5798 : support@smartro.co : http://bit.ly/smartro_01 : smartro_01
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>