Smartro SC91 Time & Temperature Projection Alarm Clock User Manual

Smartro SC91 Time & Temperature Projection Alarm Clock User Manual

Instruction Manual
Time & Temperature Projection Alarm Clock
Model:SC91

1. Preface

Thanks for choosing this device from SMARTRO.

Before You Start Using It

• Make sure to read the instruction manual carefully. This information will help you to familiarize yourself with your new device, to learn all of its functions, and to get advice in the event of problems.
• Following the instructions will prevent damage to your device.
• We shall not be liable for any damage occurring as a result of not-following of these instructions.
• Please keep this instruction manual for future reference

2. Attention

• Please follow the instructions for operation.
• Please use the original or manufacturer specified attachments or accessories.
• Do not disassemble the product, so as not to cause trouble or safety hazards.
• Do not place any items on top of the product or damage the product.
• Do not place the product near water source or in a damp place.
• Please terminate use immediately upon damage which is caused as a result of improper use or repair by a non-factory approved technician.
• Do not place the product in direct sunlight and high temperature places (radiator, electric heater, stove, etc.).
• Keep the product away from strong electromagnetic waves, strong static electricity, or moisture and condensation.
• Use by children below 10 years old should be supervised by an adult.
• Clean your device with a soft damp cloth. Do not use solvents or scouring agents.

3. Package Content

• Alarm clock (with battery)*1
• Instruction manual*1
• DC power adapter*1
• Wireless remote sensor *1

4. Product Specification

• Projection time and temperature onto a wall or ceiling (digital)

• Two alarms with Snooze function

• Calendar (up to the year of 2099)

• 12/24 hour format is alternative

• 7 Languages of Weekday selectable: English, German, Italian, French, Spanish, Dutch and Danish

• Adjustable brightness of backlit and projection

• Humidity: Indoor & Outdoor measurable range: 19%RH ~ 96%RH

• Temperature:
  — Indoor temperature measurement ranges: 15°F (-9.9°C) to 122°F (50°C)
  — Outdoor temperature measurement ranges: -40°F (-40°C) to 158°F (70°C)
  — Temperature alternatively in °F or °C
  — Outdoor thermometer and frost alert

• Minimum/maximum display for air humidity and temperature

• Outdoor dew point temperature and heat index query

• Three level display mold risk

• Wireless remote sensor
  — 3 channels available
  —Wall mount or table stand
  —200 feet signals range in an open area

• Weather forecast function

• Power supply:
  Weather Station:
  —Battery: CR2032 x1
  —DC power adapter: 5.0V 1.2A
  Wireless remote sensor
  —Battery: 2xAA 1.5V

F.Y.I.:

The wireless remote sensor can work at -40°C to +70°C. Please choose the right battery according to the limit temperature of the wireless sensor:
Alkaline zinc manganese battery can work at -20°C to +60°C.
Polymer lithium ion rechargeable battery can work at -40°C to +70°C.

5. Function Introduction

Part A-Positive LCD

A1: Time
A2: Calendar
A3: Week
A4: Weather Forecasting
A5: Outdoor Temperature
A6: Outdoor Humidity
A7: Indoor Humidity
A8: Indoor Temperature

Part. B – Back Button and Power

B1: “SET” button
B2: “ALARM” button
B3: ” ” button
B4: “SNOOZE/LIGHT” button
B5: ” ” button
B6: ” ” button
B7: ” ” button
B8: Projector
B9: Temperature sensor
B10: Alarm1 on/off switch
B11: Alarm2 on/off switch
B12: Projection on/off switch
B13: Battery compartment
B14: Power supply socket

Part C –Wireless Remote Sensor

C1: LCD display – Temperature
C2: LCD display – Humidity
C3: Transmit signal LED
C4: “°C/°F” button
C5: “TX” button
C6: “CHANNEL 1 or 2 or 3” switch
C7: Battery compartment

6. Getting Start

• Plug in the power adapter to the clock.
• When the clock is successfully connected to the power supply, all the symbols on the LCD display will light up. You will hear a “di di di” sound. The projection clock starts to detect indoor temperature and humidity.
• At the same time, unscrew the battery cover according to the OPEN direction note, take out the battery insulation sheet. Screw the battery cover back.This battery is used for keeping manual setting only, it can’t be used as a normal working power supply.
• Open the wireless remote sensor battery compartment cover, set channel for the wireless remote sensor through the C7 position and Insert 2 x AA batteries to each wireless remote sensor. Ensure that the battery polarities [ “+” and “–”] are correct. Close the battery compartment.
• The projection clock starts to make a connection with the wireless remote, displayed by a flashing reception RF antenna symbol in the channel display area on the LCD screen. This procedure will take about 3 minutes maximum.
• After the clock receiver made a connection to the outdoor wireless remote sensor, it will enter the normal mode.

7. Manual Setting

• Press and hold the ” SET ” button for more than 3 seconds, 12Hr/24Hr display starts to flash. Use the ” ” and ” ” buttons to set the time format to 24Hr mode or 12Hr mode.
• Press ” SET ” to confirm your setting, the Hour display starts to flash. Use ” ” and ” ” buttons to set the correct hour.
• Press ” SET ” to confirm your setting, the Minute displays starts to flash. Use” ” and ” ” buttons to set the correct minute.
• Press ” SET ” button to confirm your setting, the Year display 2018 starts to flash, Use ” ” and ” ” buttons to set the correct year.
• Press ” SET ” button to confirm your setting, the Month display starts to flash. Use ” ” and ” ” buttons to set the correct month.
• Press ” SET ” button to confirm your setting, the Date display starts to flash. Use ” ” and ” ” buttons to set the correct date.
• Press ” SET ” button to confirm your setting, the Month and Date icon display starts to flash. Use ” ” and ” ” buttons to set the date display on Month/Date or Date/Month.
• Press ” SET ” button to confirm your setting, the language selection for the Weekday displays starts to flash. Use ” + ” and ” ” buttons to select a language.

• Press ” SET ” button to confirm your setting, the weather forecast pattern display starts to flash. Use ” ” and ” ” buttons to select the current weather pattern.
  Press ” SET ” to confirm your setting and to end the setting procedures, enter the clock mode.

Please take note of the following:

• The clock will automatically quit the manual setting mode to clock mode if no button is pressed within 30 seconds.
•  There are 7 languages of Weekday: English, German, Italian, French, Spanish, Dutch and Danish.

8. Alarm Function Setting

8.1 Activate/Deactivate the Alarm Function

• When the switch of alarm 1 or alarm 2 is moved to the ” ON ” position, the symbol of ” ” or ” ” appears on the LCD display. The alarm function will be activated.
• When the switch of alarm 1 or alarm 2 is moved to the ” OFF ” position, the symbol of ” ” or ” ” disappears. The alarm function will be deactivated.

8.2 Manual Setting of the Alarm

• Press ” ALARM ” button can switch the display ALARM1 time or ALARM2 time.
• Press and hold ” ALARM ” button for more than 3 seconds the hour display of the Alarm 1 starts to flash. Use the ” ” and ” ” buttons to set the required hour.
• Press ” ALARM ” button to confirm your setting, the Minute display of the Alarm 1 starts to flash. Use the ” ” and ” ” buttons to set the required minute.
• Press ” ALARM ” button to confirm your setting, the Repeat icon “M-F” of the Alarm 1 starts to flash. Use the ” ” and “ ” buttons to set the alarm repeat in ” M-F ” , ” S-S ” or ” M-F ” and ” S-S “.
• Press ” ALARM ” button to confirm your setting, the snooze time of the Alarm 1 starts to flash. Use the “ ” and “ ” buttons to set the snooze time you need or turn off the Snooze function.
• Press ” ALARM ” button to confirm your setting, the Hour display of the Alarm 2 starts to flash. Use the “ ” and “ ” buttons to set the required hour.
• Press ” ALARM ” button to confirm your setting, the Minute display of the Alarm 2 starts to flash. Use the “ ” and “ ” buttons to set the required minute.
• Press ” ALARM ” button to confirm your setting, the repeat icon ” M-F ” of the Alarm 2 starts to flash. Use the “ ” and “ ” buttons to set the alarm repeat in ” M-F ” , ” S-S ” or ” M-F ” and ” S-S “.
• Press ” ALARM ” button to confirm your setting, the snooze time of the Alarm 2 starts to flash. Use the “ ” and “ ” buttons to set the snooze time you need or turn off the Snooze function.
• Press ” ALARM ” button to confirm your setting and to end the setting procedure.
• Alarm repeat setting.
  — M-F:The alarm function will be activated from Monday to Friday.
  — S-S:The alarm function will be activated on Saturday and Sunday.
  — M-F and S-S:The alarm function will be activated throughout the week.

Please take note of the following:

• The clock will automatically switch from setting mode to normal mode if no button is pressed within 30 seconds.
• The alarm will sound for 2 minutes if you do not deactivate it by pressing any button. In this case the alarm will be repeated automatically after 24 hours.

8.3 Turn off the Alarm Tone

• Alarm tone will automatically turn off after 2 minutes or you can press any button except ” SNOOZE/LIGHT ” to turn off the alarm tone. The alarm will repeat automatically at the same time of the next day.

8.4 Snooze Function

• Under the Snooze function activated status. You can activate the Snooze function by pressing ” SNOOZE/LIGHT ” when the alarm is ringing. The symbol of ” ” or ” ” starts to flash, then alarm will ring again after the Snooze time.
• Under the Snooze function activated status. Press any button except ” SNOOZE/LIGHT ” button or press and hold ” SNOOZE/LIGHT ” button for 2 seconds to exit the snooze mode.
• If one alarm is in Snooze function, the other alarm rings, it will automatically stops the Snooze function of the first alarm.

Please take note of the following:

• The alarm will keep ringing for 2 minutes if you do not deactivate it by pressing any button. In this case the alarm will automatically repeat the next day.
• The ring of the alarm changes 4 times in total during the past 2 minutes.
• The Snooze time setting range: 5 ~ 60MIN, OFF, when set to OFF, means no Snooze function

9. Projection Setting

• When the projection shift switch is pushed in the ” ON ” position, the projection display will light up.
• When the projection shift switch is pushed in the ” OFF ” position, the projection display will be closed. Under this states, press ” SNOOZE/LIGHT ” button to light up the projection for 15 seconds.
• Press and hold ” ” button for about 3 seconds to switch the brightness of projection from high to low, or low to high.
• Shot press ” ” button to adjust the projection angle by 180°.
• The suggested distance of projection is 3.3 ~ 9.8 ft (1 ~ 3 m). When there is no light at night, the clock can clearly display the time and temp on the wall or ceiling.
• The contents of the projection display are time and indoor or outdoor temperature composition. The projection will circularly display every 5 seconds for indoor / outdoor temperature.

10. Backlit Adjustment

• When the clock is powered by DC power adapter, the battery will automatically disconnect with the power supply, the backlit will be bright all the time.
• Press ” SET ” button to adjust 4 backlit brightness, light – medium – low – out.
• Press ” SNOOZE/LIGHT ” button to light up backlit for 15 seconds when the backlit in out status.

11. Wireless Remote Sensor Pairing & Manual Setting

11.1 Wireless Remote Sensor Pairing

Step 1:
— Connect the weather station with power supply.
— Insert 2 x AA batteries to each wireless remote sensor.

Step 2:
— Select channel through the “1 2 3″ knobs for the wireless remote sensor. The indicator light up once to indicate the detected temperature and humidity were sent out by wireless remote sensor.
— Select a channel for the weather station that corresponds to the wireless remote sensor. Press ” ” button to select CH1, CH2, CH3 or CH1 to CH3 (every 5 seconds automatically switch a channel).
— The weather station can connect up to 3 wireless remote sensors at the same time. If multiple wireless remote sensors were used simultaneously, they can not be set as the same channel (a total of 1, 2, 3 channel can be set).
—When the weather station successfully receives signals from the wireless remote sensor, the temperature and humidity detected by the wireless remote sensor are displayed on ” OUTDOOR REMOTE ” column of the weather station.

11.2 Manually Start the Wireless Remote Sensor Signal Reception

If “–” displayed on the weather station, it indicates the weather station failed to receive signals from wireless remote sensor, please take following operations.

— Press and hold ” ” button for 3 seconds to receive signals manually. The outdoor temperature will show an animation of the RF antenna symbol, the weather station will try to receive signals from the wireless remote sensor again.

— Press ” TX ” button on wireless remote sensor to send out signals manually.

11.3 °C/°F Temperature Display

The temperature displayed on wireless remote sensor either in °C or °F. Briefly press ” °C/°F ” button allows you to switch between the individual modes

11.4 Placement of wireless sensors

• The wireless remote sensor is not waterproof.
• The sensor can be placed anywhere (indoor or outdoor) you want to measure the temperature remotely.
• If you want to measure the outdoor temperature, please place the sensor outside away from direct sunlight and rain such as under eaves or on a porch.

Please take note of the following:

• When the outdoor temperature is between –1°C ~ 2.9°C (30.2°F ~ 37.3°F), the frost alarm function will be activated and a flashing ” ” symbol will be displayed on the weather station.

12. Temperature

12.1 Display and Trend of Temperature/Humidity

• The current indoor temperature/humidity and the temperature/humidity trend (indoor) are shown on the LCD display.
• After connected with the outdoor sensor successfully, the outdoor temperature/humidity and the temperature/humidity trend (outdoor) can be shown on the LCD display.

You may see the following displays:

No display: The temperature/humidity is remaining constant.

12.2 °C or °F Temperature Display

• The temperature displayed on the weather station either in °C or °F. Briefly pressing the ” ” button allows you to switch between the individual modes.

12.3 Max/Min Temperature & Humidity, Dew Point Temperature and Heat

Index

• To toggle indoor/outdoor sensor maximum, minimum temperature data, outdoor sensor dew point temperature date, heat index, press the ” ” button:
• Once to display the maximum temperature values of indoor and outdoor sensor.
• Twice to display the minimum temperature values of indoor and outdoor sensor.
• Three times to display the dew point temperature values of outdoor sensor.
• Four times to display the heat index values of outdoor sensor.
• Five times to return to the current temperature levels.
• To reset the maximum and minimum temperature, press and hold down the ” ” button more than 2 seconds. This will reset all minimum and maximum data recorded to the current displayed values.

Please take note of the following:

• If the temperature reading is below the measurement range, LL.L will be displayed.
• If the temperature reading is above the measurement range, HH.H will be displayed.

12.4 Outdoor Temperature Frost Alarm

• When the outdoor temperature is between –1°C ~ 2.9°C (30.2°F ~ 37.3°F), the frost alarm function will be activated and a flashing ” ” symbol will be displayed on the weather station.

12.5 Outdoor Sensor Mold Risk

• Moldy risk total 3 levels: LO ME and HI, when the risk level is HI, please check the room or outdoor sensor and pay attention to dehumidification.

13. Weather Forecast

13.1 Weather Forecast Statement

• The weather station calculates weather forecast for the next 12 hours based on the barometric pressure trend.
• The weather forecast can’t be compared with the professional weather services supported by satellites and high performance computers. It provides an approximate indication of current developments.
• Please take the weather forecast from local weather station as authoritative.

13.2 The Symbols of Weather Forecast

Please take note of the following:

• When the wireless sensor detects that the outdoor temperature falls below -4°C (24.8°F) in a rainy day. The weather forecast will display snowy (The default detection temperature is from CH1 to CH2, CH3).

13.3 Barometric Pressure Trend

You may see the following symbols:

15. Troubleshooting

16. After-sales Support

Please contact us if your device fails to work despite these measures or your experience with us is less than perfect in anyway. Or Join our Instagram or Facebook group for more support and discount information.

E-Mail: support@smartrostore.com

Phone: +1(323)287-5798

Facebook: http://bit.ly/smartro_01

Instagram: smartro_01

17. Waste Disposal

• This product has been manufactured using high-grade materials and components which can be recycled and reused.

• As a consumer, you are legally required to take them to your retail store or to an appropriate collection site depending on national or local regulations in order to protect the environment.

• The symbols for the heavy metals contained are: Cd=cadmium, Hg=mercury, Pb=lead.

• Please do not dispose of this instrument in household waste. The user is obligated to take end-of-life devices to a designated collection point for the disposal of electrical and electronic equipment, in order to ensure environmentally-compatible disposal.

DOWNLOAD

Smartro SC91 Time & Temperature Projection Alarm Clock User Manual – [Download PDF]

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>