TECH PS-06m DIN Rail Relay Module Instruction Manual

: June 13, 2024
: TECH

Table of Contents

TECH PS-06m DIN Rail Relay Module
Product Information
Product Usage Instructions
Description
Manual mode
Technical data
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TECH PS-06m DIN Rail Relay Module

Product Information

Product Name: PS-06m
Manufacturer: TECH STEROWNIKI II Sp. z o.o.
Website: www.sinum.eu
Available Languages: Polish (PL), English (EN), Czech (CZ), Slovak (SK), German (DE), Hungarian (HU), Dutch (NL), Romanian (RO), Russian (RU)

Technical Support Contact Information:

Poland:
tel: +48 33 875 93 80,
email: serwis.sinum@techsterowniki.pl
Czech Republic:
tel: +420 733 180 378,
email: cs.servis@tech-reg.com
Slovakia:
tel: +421 918 943 556,
email: sk.servis@tech-reg.com
Netherlands:
tel: +31 341 371 030,
email: info@eplucon.nl
Romania:
tel: +40 785 467 825,
email: contact@tech-controllers.ro
Hungary:
tel: +36-300 919 818, +36 30 321 70 88,
email: szerviz@tech-controllers.com
Ukraine:
tel: +38 096 875 93 80,
email: servis.ua@tech-controllers.com

Product Usage Instructions

To identify the device in the Sinum system:

Activate the Identification Mode in the Settings > Devices > SBUS Devices menu.
Click on the “+” button to add a new device.
Select the Identification Mode tab.
Hold the registration button on the device for 3-4 seconds.
The device used will be highlighted on the screen.

Technical Specifications:

Power Supply: 230V AC / 0.5A (AC1), 24V DC / 0.5A (DC1)
Max. Power Consumption: 2W
Rated Load of the Voltage-Free Contact 1-6
Operating Temperature: Not specified
Acceptable Ambient Relative Humidity: Not specified

The PS-06m module is an electronic device equipped with 6 independent voltage- free relays enabling the user to control 6 independent devices. It is designed to be mounted on a DIN rail. Communication with the Sinum central device is done by wire.

Description

Power supply
Communication
1-6 Current status of the voltage-free output (ON/OFF)
SBUS communication connector
Voltage-free contact connector ! WARNING ! Only one type of potential should be used within connector: 24V or 230V.
Voltage-free contact connector ! WARNING ! Only one type of potential should be used within connector: 24V or 230V.

Manual mode

In order to switch to the manual operation mode, press the manual operation button 1. The registration button 2 is used to switch between the controlled outputs in the manual mode. Using the button 1 (pressing it once), the user forces a change of the status (ON / OFF) – if the process has been successful, it is confirmed by a light signal from the LED labelled 1-6. When the manual mode is on, it is impossible to control the contact via the website or the application. To disable the manual mode, press the button 1 again and hold it for 1-2 seconds. Once the manual mode has been switched off, all the output status LEDs go off and resume the state set in the Sinum application

How to register the device in the sinum system

The device should be connected to the Sinum central device using the SBUS connector 3, and then enter the address of the Sinum central device in the browser and log in to the device. In the main panel, click the Settings > Devices > SBUS devices > + > Add device. Then briefly press the registration button 2 on the device. After a properly completed registration process, an appropriate message will appear on the screen. Additionally, the user can name the device and assign it to a specific room.

How to identify the device in the Sinum system

To identify the device in the Sinum Central, activate the Identification Mode in the Settings > Devices > SBUS Devices > + > Identification Mode tab and hold the registration button on the device for 3-4 seconds. The device used will be highlighted on the screen.

Technical data

Power supply| 24V DC ±10%
Max. power consumption| 2W
Rated load of the voltage-free contact 1-6| 230V AC / 0,5A (AC1) *****

24V DC / 0,5A (DC1) **

Operation temperature| 5°C ÷ 50°C
Acceptable ambient relative humidity| <80% REL.H

Notes

TECH Controllers is not responsible for any damages resulting from improper use of the system. The range depends on the conditions in which the device is used and the structure and materials used in the object construction. The manufacturer reserves the right to improve devices, update software and related documentation. The graphics are provided for illustration purposes only and may differ slightly from the actual look. The diagrams serve as examples. All changes are updated on an ongoing basis on the manufacturer’s website. Before using the device for the first time, read the following regulations carefully. Not obeying these instructions may lead to personal injuries or controller damage. The device should be installed by a qualified person. It is not intended to be operated by children. It is a live electrical device. Make sure the device is disconnected from the mains before performing any activities involving the power supply (plugging cables, installing the device etc.). The device is not water resist

The product may not be disposed of to household waste containers. The user is obliged to transfer their used equipment to a collection point where all electric and electronic components will be recycled.

EU Declaration of conformity

Tech Sterowniki II Sp. z o.o. ul. Biała Droga 34, Wieprz (34-122)
Hereby, we declare under our sole responsibility that the modul PS-06m
is compliant with Directive :