SUNRICHER AC Phase Cut RF+Bluetooth Dimmer Instruction Manual

: June 6, 2024
: SUNRICHER

Table of Contents

Function introduction
Product Data
Safety & Warnings
Operation
Pair with smart APP
Setting minimum brightness:
Delete the minimum brightness:
Controlled by a push switch:
Wiring diagram
Product Dimension
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AC Phase Cut RF+Bluetooth Dimmer
Instruction Manual

SUNRICHER AC Phase Cut RF Bluetooth Dimmer - FC CE
Important: Read All Instructions Prior to Installation

Function introduction

SUNRICHER AC Phase Cut RF Bluetooth Dimmer - Function
introduction

Product Data

Input Voltage	Output Voltage	Output Current	Size(LxWxH)
100-240VAC	100-240VAC	1.8A max	45.5x45x20.3mm

Compatible Load Types

AC phase-cut dimmer based on RF+Bluetooth Mesh
100-240VAC Wide Input and Output Voltage
Supports resistive loads and capacitive loads
1 Channel Output, Up to 400W
Input and Output with Screw Terminals, Safe and Reliable
Both leading edge version and trailing edge version are available for choosing, default factory setting is trailing edge
Enables to control ON/OFF and light intensity of connected triac dimmable led light or led driver
Controlled through both smart App and remote controls, no gateway required
Easy & quick pairing to the smart App by simply pushing the reset button
Mesh network, much longer control distance, transmits received signal to neighbor devices
Up to 30m transmission distance between every two neighbor devices
Encrypted two-way communication, quick status feedback, safe & reliable data transmission
Compatible with universal RF+Bluetooth remotes, each LED controller can pair to max. 8 remotes
Cloud control is available for remote access, works with Amazon Alexa and Google Home
Can be controlled by universal 8-230V input single wire push switch
Mini Size, Easy to be installed into a standard 86*86mm wall box
Radio Frequency: 2.4GHz
Waterproof grade: Ip20

Safety & Warnings

DO NOT install with power applied to the device.
DO NOT expose the device to moisture.

Operation

Pair/delete the pairing with RF+Bluetooth remote

Do wiring according to the connection diagram.
Pair LED controller with RF+Bluetooth remote: please refer to the instruction of the remote that you would like to pair with.
Delete the pairing:
(1) Wire up the LED controller correctly, power on.
(2) Press and hold down the “ Reset” button on the controller for over 3 seconds (or reset the power of the device 8 times continuously if the button is not accessible to factory reset the device) until the connected light flashes, which means well deleted.

Note: factory resetting will restore all configured parameters of the device on the APP to the factory default setting.

Pair with smart APP

Do wiring according to the connection diagram.
Please refer to the EasyThings App user manual for details of adding devices.

Setting minimum brightness:

Adjust brightness to the desired level from Zigbee hub or controller interface or a remote, then press and hold down the “Min. Set ” key until connected light flashes, the minimum dimming level is set successfully, then the connected load can only be dimmable between this minimum brightness and 100% brightness. The dimming range of this dimmer is 1%-100%, but some load types may flicker when dimmed to 1%, thus a minimum brightness shall be set higher than 1% to avoid flickering during the dimming process.

Delete the minimum brightness:

Adjust the brightness to 100% from Zigbee hub or controller interface or a remote, then press and hold down the “Min.
Set” key on the dimmer until connected light flashes, which means minimum brightness is deleted successfully.

Controlled by a push switch:

Once connected with a push switch, click the push switch to switch ON/OFF, press, and hold down it to increase/decrease light intensity.

Wiring diagram

Notes for the diagrams:
L – terminal for live lead
N – terminal for neutral lead
Out – output terminal of the dimmer (controlling connected light source)
+A1 – terminal for push switch
-A2 – terminal for grounding to the switch connected to the dimmer

With Single Push Switch
With Multiple Push Switches for Multiple Control Points

SUNRICHER AC Phase Cut RF Bluetooth Dimmer - Wiring diagram
1

This phase dimmer adopts leading edge dimming (forward phase control) or trailing edge dimming (reverse phase control), two versions are available for choosing, the default factory setting is trailing edge, leading edge version is available upon request. Please make sure the connected loads support the control type you choose. Please refer to the user manual of the load or consult the supplier of the load.