SAMSON SM4 4-Channel Mixer Interface with Bluetooth Owner’s Manual
- June 6, 2024
- SAMSON
Table of Contents
MEDIA TRACK
USB MIXER/INTERFACE WITH BLUETOOTH
Important Safety Information
ATTENTION RISQUE DE CHOC ELECTRONIQUE -NE PAS OUVRIR
This lightning flash with an arrowhead symbol within an equilateral triangle
is intended to alert the user to the presence of non-insulated “dangerous
voltage” within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance instructions in
the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK) AS THERE ARE NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The Bluetooth word mark and logos are registered trademarks owned by Bluetooth
SIG. Inc. and any use of such marks by Samson Technologies is under license.
Other trademarks and trade names are those of their respective owners?
If you want to dispose of this product, do not mix it with general household
waste. There is a separate collection system for used electronic products in
accordance with legislation that requires proper treatment, recovery, and
recycling. I Private household in the 28 member states of the EU. in
Switzerland and Norway may return their used electronic products free of
charge to designated collection facilities or to a retailer (if you purchase a
similar new one). For Countries not mentioned above, please contact your local
authorities for a correct method of disposal. By doing so you will ensure that
your disposed product undergoes the necessary treatment. recovery and
recycling and thus prevent potential negative effects on the environment and
human health.
MEDIA TRACK MIXER
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators. heat registers. stoves. or other apparatus (including amplifiers) that produce heat.
- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. It the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
- Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer. or sold with the apparatus. When a cart is used, use caustic when moving the cart/apparatus combination to avoid injury from tip-over.
- Unplug the apparatus during lightning, short circuit or when unused for long periods of time.
- Refer all servicing to qualified personnel. Service is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
- This appliance shall not be exposed to dripping or splashing water and that no object filled with liquid such as vases shall be placed on the apparatus.
- Caution – to prevent electrical shock, match wide blade plug to wide outlet slot fully insert the plug into the outlet.
- Please keep a good ventilation environment around the entire unit.
- WARNING: The direct plug-in adapter or AC/DC adapter is used as a disconnect device, the disconnect device shall remain readily operable.
- No naked flame sources, such as lighted candles, should be placed on the apparatus.
- This apparatus is intended to be used in moderate and/or tropical climates.
FCC Notice
1. This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference. (2) This device must accept any interference received. including
interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions. may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 centimeters between the radiator and your body.
RF Warning Statement
This device complies with RSS 310 of Industry Canada. Operation is subject to
the condition that this device does not cause harmful interference. Hereby.
Samson Technologies Corp. declares that this MEDIA TRACK is in compliance with
the essential requirements and other relevant provisions of Directive
2014/53/EU. The declaration of conformity may be consulted at:
http://www.samsontech.comrsite_media/support/manuals/MEDIATRACK_DOC.pdf
Introduction
Thank you for purchasing the Samson MediaTrack USB Mixer/Interface. The
MediaTrack rack mounts USB mixer is a versatile tool for many sound and
recording applications. It features microphone and music inputs,
Bluetooth•connectivity for streaming audio, and a USB jack for connecting an
optional Samson XPD USB Digital Wireless System. In the box, you’ll find a
registration card enclosed—please don’t forget to follow the instructions so
that you can receive online technical support and so we can send you updated
information about this and other Samson products in the future. Also, be sure
to check out our website (wvny.samsontech.com) for information about our full
product line. We recommend you keep the following records for reference, as
well as a copy of your sales receipt.
Serial number:…………………….
Date of purchase:………………
If you have any questions or comments regarding the MediaTrack or any other
products from Samson, do no hesitate to contact us at
support@samsontech.com. With proper care and
maintenance, your MediaTrack will operate trouble-free for many years. Should
your MediaTrack ever require servicing? a Return Authorization (RA) Number
must be obtained before shipping your unit to Samson. Without this number, the
unit will not be accepted. Please visit
www.samsontech.com/ra for an RA number prior
to shipping your unit. Please retain the original packing materials and, if
possible, return the unit in its original carton. If your MediaTrack was
purchased outside of the United States, contact your local distributor for
warranty details and service information.
Features
- 4-channel stereo line mixer
- USB Interface for connecting with computers or tablets
- XLR-1/4″ balanced microphone input
- Stereo line channel with RCA, 1/4″, and 1/8″ (3.5mm) inputs
- Bluetooth connectivity to wirelessly stream from a mobile device
- Samson XPD Wireless USB Port (system sold separately)
- Voiceover priority ducking with variable hold time
- 15V phantom power
- Rackmount kit and power adapter included
Front Panel callouts
- Power Switch – Use this switch to turn the MediaTrack on and off. To avoid potential damage to your speakers, turn the MediaTrack on before you turn on any connected power amps, and turn it off after the power amps are turned off.
- Power Indicator – LED lights green indicating the unit is powered on.
- MIC Volume – This knob controls the level of the MIC input. 4. XPD Level – This knob controls XPD Wireless volume level.
- MUSIC Volume – This knob controls the level of the Music inputs (rear panel RCA, front panel 1/4″ and 1/8″) and the Bluetooth audio.
- VOICEOVER – Controls the amount the Music and Bluetooth audio will be lowered (ducking) when there is a signal present at the Mic channel.
- USB Level – Controls volume of USB computer audio stream to the MediaTrack audio outputs.
- 1/8″ (3.5mm) Music Inpu t – Stereo 1/8″ (3.5mm) jack to connect line-level sources. The level of this input is controlled by the MUSIC Volume knob.
- 1/4″ Music Input – Stereo 1/4″ jack to connect line level sources. The level of this input is controlled by the MUSIC Volume knob.
- Pairing Indicator – Displays the Bluetooth status of the MediaTrack.
- Pairing Button – Press and hold this button to enable discoverable mode in order to pair with a Bluetooth audio device. The LED will blink quickly when the discoverable mode is enabled.
- Samson XPD WIRELESS USB Input – Connect an optional Samson XPD USB Digital Wireless receiver to this input. The wireless level is controlled by the XPD Volume control.
- Bluetooth Antenna – This antenna receives the signal from a paired device and should be placed in a vertical position when using Bluetooth. The Bluetooth receiver has a range of approximately 100′ (30m).
Real Panel callouts
- DC Input – Connect the supplied power adapter here, using the strain relief* as shown in the illustration below. WARNING: Do not substitute any other kind of power adapter. Doing so can cause severe damage to the MediaTrack and will void your warranty.
- BAL MIC INPUT – Use this Combo XLR plus 1/4″ jacks to connect a microphone or wireless microphone receiver. The XLR input provides 15-volt phantom power for use with condenser microphones.
- Stereo RCA MUSIC INPUT – Stereo line-level input for connecting the output of devices such as MP3, CD, or any line level audio device using standard RCA cables.
- VOICEOVER HOLD – This knob controls the hold time of the VOICEOVER priority ducking from 0.5s-3s.
- MASTER VOLUME – The MASTER VOLUME knob controls the overall output level. This knob determines the final output signal level. Signals from all channels are routed here just before being routed to the OUTPUT jacks.
- Balanced XLR OUTPUT – Balanced XLR outputs to connect the MediaTrack to a power amplifier or speakers. In recording applications, these outputs can be used to connect to a stereo device such as a computer sound card, MP3, or hard disk recorder. The signal at the OUTPUT jacks follows the MASTER VOLUME control.
- STEREO / MONO Switch – When the switch is in the out, STEREO position, the left, and right signals are routed to the corresponding outputs. In the in, MONO, position, the left, and right input signals are summed together and fed to both Left and Right OUTPUT jacks.
- Unbalanced RCA OUTPUT – Unbalanced RCA outputs to connect the MediaTrack to a power amplifier or speakers. In recording applications, these outputs can be used to connect to a stereo device such as a computer sound card, MP3, or hard disk recorder. The signal at the OUTPUT jacks follows the MASTER VOLUME control.
- USB C OUTPUT – Using the supplied USB C cable connect your laptop or tablet to record your performance. Adjust the input level with the USB control knob on the front panel.
“Using the strain relief: Gather up a loop of wire and pass it through the strain relief, then pass the adapter plug through the loop in order to create a knot
Quick Start
-
Remove all packing materials and decide where the unit is to be physically placed. The MediaTrack can be mounted in any standard 19″ rack (requiring one rack space), or used on a tabletop.
-
Before connecting a microphone or line-level audio device, make sure that the power to all your systems components, including the MediaTrack, is turned off.
-
Using an XLR or 1/4″ cable, connect a wired microphone or the output of a wireless microphone receiver to the Mic input jack on the rear of the MediaTrack.
-
Connect a music source, like a CD player, to the RCA jacks on the rear panel of the MediaTrack. The red connector is the right input and the white connector is the left input. Portable audio devices, like an MP3 player, can be connected to the 1/4″ or 1/8″ stereo inputs on the front of the MediaTrack.
-
Connect the outputs of the MediaTrack to the inputs of a power amplifier or speaker system using XLR or RCA cables.
-
Turn the MediaTrack Master Volume control all the way down and turn the MediaTrack power on.
NOTE: It is important to remember the Golden Rule of audio … “LAST ON, FIRST OFF”. Translated, this means that when turning on your system, you should always turn your power amplifiers or powered monitors on LAST, and when turning your system off, turn your power amps off FIRST. This helps avoid any loud pops caused by inrush current at power-up, which can sometimes damage loudspeakers. -
Turn the power amplifier or speaker system on and turn the volume up.
-
Set the MIC volume control of the MediaTrack to the 12 o’clock position.
-
While talking into the microphone, raise the MASTER VOLUME control until you have reached the desired level.
-
Play music from the connected music source and raise the MUSIC volume control. Adjust the MIC and MUSIC volume until the microphone signal is able to be heard above the music.
Avoiding Feedback
Feedback is the annoying howling and squealing that can be heard when the
microphone picks up sound from the speaker. The sound is then re-amplified
back through the speaker again, creating a feedback loop. Follow these steps
to minimize the likelihood of feedback:
- Avoid pointing the microphone directly at the speakers. In general, it is recommended that the microphone be positioned behind the speaker enclosure. This uses the directional characteristics of the speaker and microphone to your advantage.
- Keep the microphone as far from the speakers as possible. This will help achieve isolation between the speaker and the microphone.
- Position the microphone as close to the sound source as possible. This will enable the microphone to pick up more direct sound and allow you to reduce the microphone input gain control.
Pairing with a Bluetooth® device
Bluetooth is a wireless communication technology that allows for connectivity between a wide range of devices. The MediaTrack uses Bluetooth to stream high- quality audio from your Bluetooth-enabled device without the need for connecting any cables. In order for your device to work with the MediaTrack, it must first be paired.
- With the MediaTrack and your Bluetooth device powered on, press and hold the PAIR button on the front panel of the MediaTrack mixer to make the mixer discoverable. The white Bluetooth indicator will flash slowly.
- In the settings of your Bluetooth device, set it to “discover” available devices.
- From the Bluetooth device list, select the “SAMSON BLUETOOTH” device.
- If your device asks for a passkey, enter digits 0000 (four zeros) and press OK. Some devices may also ask you to accept the connection.
- As the MediaTrack is connecting to your device, the Bluetooth indicator will quickly flash white.
- The MediaTrack indicates that pairing is complete when the indicator turns steady white. You can now stream audio from your device to the MediaTrack.
- On your Bluetooth device, set the volume to the maximum setting and start playing music.
- Use the MUSIC volume knob on the front panel of the MediaTrack to set the desired level of the Bluetooth audio.
Specifications
F requency Response (to XLR balanced output, re +4 dBu output)
Music Inputs (1/4″, 1/8″, RCA)
XLR Mic Input
Bluetooth
USB Playback| 20Hz-20kHz, +0/-0.5dB, 200 source
73.5Hz-20kHz, +01-3dB, 1500 source
20Hz-20kHz, +01-3dB
12.4Hz-18.2kHz, +0/-1dB
---|---
THD+N (to XLR balanced output, re +4 dBu output)
Music Inputs (1/4″, 1/8″, RCA)
XLR Mic Input
Bluetooth
USB Playback| <0.004%, 25Hz-17kHz, 200 source
<0.006%, 75.5Hz-20kHz, 1500 source
<0.01%, 20Hz-20kHz
<0.005%, 20Hz-20kHz
---|---
Equivalent Input Noise
XLR Mic Input| -108dBu, A-weighted, max gain
(1°/0THD+N output),1500 source
---|---
Maximum Gains (to XLR balanced output, master volume maximum, lkHz test
tone)
Music inputs (1/4″, 1/8″, RCA)
XLR mic input
Samson XPD System
Bluetooth
USB playback| 20.5dB, 200 source
51.6dB, 1500 source
43.1dB, 200 source
20.3dB
11.9dB
---|---
Residual Noise (A-weighted, all controls minimum)
XLR OUT
RCA OUT
USB recording| -113.8dBu
-113.8dBu
-96dBFS
---|---
Minimum input Level (1%THD+N)
Misc inputs (1/4″,1/8″,RCA)
XLR mic input| +5.46dBu, 9Hz-7kHz, +0/-0.1% THO+N, 200 source -6.58dBu,
80Hz-4.5kHz, +0/-0.1% THD+N, 1500 source
---|---
Maximum Output Level (1% THD+N)
MIC Output +14.7 dBu (1% THD+N)|
---|---
Dynamic Range
XLR Out
RCA Out| 95dB, re +15dBu output, 22kHz BW
100dB, re +15dBu output. 22kHz BW
---|---
Input Impedance (1kHz test tone)
Music Inputs (1/5″,1/8″,RCA)
XLR Mic Input| 10kΩ
1.6kΩ
---|---
Output Impedance (1 kHz test tone)
XLR Out
RCA Out| 400Ω
200Ω
---|---
Voiceover
Attack Time
Hold Time
Release Time
Maximum gain reduction| 8ms
250ms (shortest setting), 2s (longest setting)
485ms
28.6dB
---|---
USB C 110
Number of input channels
Number of output channels
Maximum sample rate
Bit depth
USB Playback to XLR Output gain
USB Output Power
Phantom Power
Power Adapter
Bluetooth
Working Frequency
RF Power
Transmission Range| 2
2
48 kHz
16 bits OdBFS = +12dBu at XLR output
USB3.0 5VDC 200mA
15VDC 15VDC 800mA (center positive/sleeve negative)
V4.0, A2DP
2.402GHz – 2.480GHz
<10mW EIRP
10m (>32′)
---|---
Dimensions and Weight
Dimensions
Weight| 8.78″ x 5.43″ x 1.69″ 223mm x 138mm x 43mm
1.88 lbs / 0.852 kg
---|---
MEDIA TRACK MIXER
Samson Technologies Corp
278-B Duffy Ave
Hicksville, New York 11801
www.samsontech.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>