SAMSON XPD2m Digital Wireless System Owner’s Manual

June 7, 2024
SAMSON

SAMSON logo XPD2m Digital Wireless System

SAMSON XPD2m Digital Wireless System Owner’s Manual

Important Safety Information

CAUTION 8520

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance.
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS. DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER  OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK HAZARDS. DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. TO PREVENT ELECTRICAL SHOCK, MATCH WIDE
BLADE PLUG TO WIDE SLOT AND FULLY INSERT.
If you want to dispose of this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery, and recycling.
Private households in the 28 member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one). For Countries not mentioned above, please contact your local authorities for a correct method of disposal.
By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery, and recycling and thus prevent potential negative effects on the environment and human health.
WARNING!
Risk of explosion if the battery is replaced by an incorrect type.
Copyright 2021, Samson Technologies Corp. v1.1
Samson Technologies Corp.
278-B Duffy Ave
Hicksville, NY 11801
www.samsontech.com

Important Safety Information

  1. Read these instructions.

  2. Keep these instructions.

  3. Heed all warnings.

  4. Follow all instructions.

  5. Do not use this apparatus near water.

  6. Clean only with a dry cloth.

  7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

  8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

  9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.

  10. Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus.

  11. Only use attachments/accessories specified by the manufacturer.

  12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
    When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
    move

  13. Unplug the apparatus during lightning storms, or when unused for long periods of time.

  14. Refer all servicing to qualified personnel. Service is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, has been exposed to rain or moisture, does not operate normally, or has been dropped.

  15. This appliance shall not be exposed to dripping or splashing water and no object filled with liquid such as vases shall be placed on the apparatus.

  16. Caution-to prevents electrical shock, match wide blade plug wide slot fully insert.

  17. Please keep good ventilation of the environment around the entire unit.

  18. The direct plug-in adapter is used as a disconnect device, the disconnect device shall remain readily operable.

  19. Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

Important Safety Information
FCC Notice

  1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
    (1) This device may not cause harmful interference.
    (2) This device must accept any interference received, including interference that may cause undesired operation.

  2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Statement (SAR)
This device is designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications Commission of the U.S. Government.
Hereby, Samson Technologies Corp., declares that this XPD2m Digital Wireless System is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/
EU. The declaration of conformity may be consulted at:
http://www.samsontech.com/site_media/support/manuals/XPD2m_DOC.pdf

Introduction

Congratulations on purchasing the Samson XPD2m Digital Wireless System.
The XPD2m Dual Channel Digital Wireless System, available in dual handheld and dual beltpack (Lavalier and Headset) configurations, operates in the license- free 2.4GHz frequency range. This system is a unique wireless microphone solution that is ideal for presenters, fitness instructors, educators, interviewers, and more.
The RXD2M tabletop receiver is compact enough to fit in any carry bag and includes two XLR jacks (CH1 & CH2), 1/4” mix output, and 1/8” mix output for easy connection to mixers and PA systems. One-touch pairing allows for straight forward connection between transmitters and each channel on the RXD2M receiver. Samson’s XPD2m Dual Channel Digital Wireless Systems have a range of 100’ and offer up to 20 hours of operation using two AA batteries.
On these pages, you’ll find a detailed description of the features of the XPD2m Dual Channel Digital Wireless System, instructions for its setup and use, and specifications. If your wireless system was purchased in the United States, you’ll also find a registration card enclosed—don’t forget to follow the instructions so that you can receive technical support and so that we can send you updated information about this and other Samson products in the future. Also, be sure to check out our website (www.samsontech.com) for complete information about our full product line.
We recommend you keep the following records for reference, as well as a copy of your sales receipt.
Transmitter & Receiver Serial numbers: _
Date of purchase: ___

If you have any questions or comments regarding the XPD2m Dual Channel Digital Wireless Microphone System or any other products from Samson, do not hesitate to contact us at support@samsontech.com.
With proper care and maintenance, your XPD2m Digital Wireless System will operate trouble-free for many years. Should your XPD2m Digital
Wireless systems ever require servicing, a Return Authorization (RA) Number must be obtained before shipping your unit to Samson. Without this number, the unit will not be accepted. Please visit www.samsontech.com/ra for an RA number prior to shipping your unit. Please retain the original packing materials and, if possible, return the unit in its original carton. If your XPD2m Digital Wireless System was purchased outside of the United States, contact your local distributor for warranty details and service information.

RXD2M Receiver Features

  1. VOLUME/Power Control – This rotary knob controls the level of the receiver output and powers the RXD2M on and off. Turn clockwise to power on and counterclockwise to power off. The light ring around the VOLUME/Power Control will illuminate white when powered on.
  2. PAIR button – Press and hold for more than three seconds to enter pairing mode, the READY LED will begin flashing. NOTE – the system is paired at the factory prior to shipment.
  3. READY Indicator – This LED displays the operation mode. Solid AMBER means normal operation, flashing AMBER means pairing, no light means not paired, or that the transmitter is either out of range or powered off.SAMSON XPD2m Digital Wireless System - Features

RXD2M Receiver Features Rear Panel

SAMSON XPD2m Digital Wireless System - Panel

  1. DC Input – Connect the supplied adapter here. WARNING: Do not substitute any other kind of power adapter. Doing so can cause severe damage to your RXD2M receiver and void your warranty.
  2. Unbalanced Outputs – Use these unbalanced 1/4” and 1/8” jacks when connecting the RXD2M receiver to consumer (-10 dBV) audio equipment. Both jacks carry a mix of Channel 1 and Channel 2’s audio signal. Wiring is as follows: tip hot, sleeve ground
  3. Balanced Output – Use one or both of these electronically balanced low impedance (600 Ohm) XLR jacks when connecting the RXD2M to professional (+4 dBu) audio equipment. Channel 1’s jack carries the signal from Channel 1 (controlled by volume 1) and Channel 2’s jack carries the signal from Channel 2 (controlled by volume 2). Pin wiring is as follows: Pin 1 ground, Pin 2 high (hot), and Pin 3 low (cold)

HXD1 Handheld Transmitter Callouts

  1. SAMSON XPD2m Digital Wireless System - Callouts Status Indicator – This LED displays the operation mode. Amber: Normal Operation Flashing Amber: Pairing / Low Battery

  2. Power/Pair Switch – Press <5 seconds to turn the unit on or off. Press >5 seconds to enter pairing mode.

  3. Battery Cover – Unscrew the battery cover and slide it down to open the HXD1 Handheld battery compartment.

  4. Battery Holder – Open the battery holder by pressing the tab and lifting the cover. Insert two standard AA (LR6) batteries here, being sure to
    observe the plus and minus polarity markings shown.
    WARNING: Do not insert the batteries backward; doing so can cause severe damage to the transmitter and will void your warranty.

  5. Input GAIN Control – This control adjusts the transmitter input sensitivity. This input sensitivity control has been factory preset to provide the optimum level for the particular microphone capsule provided with the XPD2m system and so we recommend that this not be adjusted manually. If necessary, however, you can use the supplied screwdriver to raise or lower the input level.

  6. Screwdriver – Used to adjust the input GAIN control.

PXD1 Beltpack Transmitter Callouts

  1. SAMSON XPD2m Digital Wireless System - Callouts2 Input Connector – Connect the input device via this mini-XLR input jack. The PXD1 is supplied with either a lavalier or headset microphone that is wired to a P3 connector.

  2. Status Indicator – This LED displays the operation mode. Amber: Normal Operation Flashing Amber: Pairing / Low Battery

  3. Power/Pair Switch – Press <5 seconds to turn the unit on or off. Press >5 seconds to enter pairing mode.

  4. Input GAIN Control – This control adjusts the transmitter input sensitivity.

  5. Battery Holder – Open the battery holder by pressing the tab and lifting the cover.
    Insert two standard AA (LR6) batteries here, being sure to observe the plus and minus polarity markings shown.
    WARNING: Do not insert the batteries backward; doing so can cause severe damage to the transmitter and will void your warranty.

  6. Screwdriver – Used to adjust the input GAIN control.

Quickstart

In order for the XPD2m Dual Channel Digital Wireless System to work correctly, both the RXD2M receiver and HXD1 handheld or PXD1 belt-pack transmitter must be paired together. ( NOTE: The XPD2m Digital Wireless System will come paired from the factory).
Follow this basic procedure for setting up and using your XPD2m Digital Wireless System:

  1. Physically place the RXD2M receiver where it will be used. We suggest you keep the receiver and transmitter within line of sight for optimal performance, meaning the performer using or wearing the transmitter can see the receiver.

  2. Connect the included power adapter to the RXD2M receiver before turning the power on. Turn the RXD2M on momentarily to confirm that it is receiving power, then turn it off (figure 1).
    SAMSON XPD2m Digital Wireless System - Quickstart
    SAMSON XPD2m Digital Wireless System - Quickstart2

  3. With your amplifier or mixer powered off and volume control down connect the RXD2M receiver Channel 1 output jack to the mic or line input using the balanced XLR output, unbalanced 1/4” or 1/8” output jacks. Turn the RXD2M power on but keep the volume at a minimum level (figure 2).

  4. Place a fresh set of AA (LR6) batteries in the transmitter’s battery compartment being sure to observe polarity markings (figure 3).
    SAMSON XPD2m Digital Wireless System - Quickstart3

  5. If the receiver and transmitter have not been previously paired press and hold the pair button on the RXD2M receiver for >3 seconds until the  LED begins to flash (amber). Press and continue to hold the power button on the transmitter until the LED indicators on both units light steadily indicating that the receiver and transmitter are paired and ready for operation. (figure 4)
    SAMSON XPD2m Digital Wireless System - Quickstart 4

  6. Turn on the connected amplifier or mixer but leave the PA system’s volume at the minimum level. Turn the volume control of your RXD2M fully clockwise, this is unity gain. Speak or sing into the microphone at a normal performance level while turning up the PA system’s volume control until you reach the desired output level.

  7. NOTE: Only one XPD2m system can be used at a time.

Troubleshooting

Issue Solutions
No Audio Make sure that the transmitter and receiver are both powered on.

Ensure the transmitter’s batteries are installed correctly.
Check that the transmitter volume is at an appropriate level.
Confirm that the RXD2M adapter is correctly connected and plugged into an electrical outlet.
Turn on the RXD2M receiver.
Make sure the RXD2M audio output connections are securely seated into the jacks and that the cables are functioning.
Ensure that the receiver and transmitter are in the line of sight with one another.
Check the receiver and audio input device-level controls.
Ensure that the transmitter and receiver are paired. If unsure, follow the pairing explanation on page 11, #5.
Distorted Audio| The receiver output level or audio input device level may be too high.
Check the transmitter’s batteries, and replace if low.
The input gain on the transmitter (PXD1/HXD1) or audio source output level may be too high.
Audio Dropout| The transmitter may be too far away from the receiver. Move it closer to the receiver.
Remove any sources that may cause RF interference such as cell phones, cordless phones, lighting equipment, computers, metal structures, etc.
The receiver will not power on| Check the adaptor to ensure it is properly connected and plugged into an outlet providing power.
The transmitter will not power on (LED does not light)| Replace the transmitter batteries.
Noise or interference| If using two systems, make sure both systems are paired together. If the problem persists, pair each system individually.

Specifications

System


Operating Range| 100’ (30m) line of sight
 Audio Frequency Response| 24Hz – 18kHz (+0/-3dB)
T.H.D.+N (Overall)| <0.1%, +4dBu, 22kHz BW
Dynamic Range XLR| 81.9 dB re – 1.1 dBu
Dynamic Range Unbal.| 81.3 dB re +5.3 dBu
Modulation Type|  GFSK
Oscillation  Type|  PLL
Signal to Noise| 90dB,re +4dBu, 22kHz BW
 Operating Temperature| –10°C (14°F) to +50°C (+122°F)
Operating  Frequency|    2.404~2.476+GHz0.005%
Frequency  Stability|  +/-
Max channels per system| 2
Max simultaneous systems| 1

RXD2M Receiver

Audio Output|  1kHz, 2.5kΩ load impedance
Reference Level 1/8” (3.5mm) & 1/4” (6.3mm) jack (unbalanced)| +5.3dBu max output (1%THD)
XLR jack (balanced)| -1.1dBu max output (1%THD)
Audio Output Impedance 1/8” (3.5mm) & 1/4” (6.3mm) jack (unbalanced)| 200 Ω
XLR output jack (balanced)| 2.15 kΩ
 RF  Sensitivity|  -78dBm/20dB SINAD
Antennas| 1/4 wavelength, 1.2”(3.1cm)
Operating Voltage| +5VDC  (center positive)
Operating Current| 100mA
Max Current Consumption| 125 mA
Dimensions (LxWxH)| 5.1” x 5.1” x 1.46” 130mm x 130mm x 37mm
Weight| 0.57lb / 0.26kg

PXD1 Transmitter

Input Connector| Mini-XLR(P3)
RF Power| <10 mW EIRP
Power Requirements| Two AA (LR6) alkaline batteries
Battery Life| 20h
Dimensions (WxHxD)| 3.75” x 2.44” x 0.75” 96mm x 62mm x 18.5mm
Weight| 0.2lb /93g

HXD1 Transmitter

Microphone Element| Q6 Dynamic
RF Power| <10 mW WIRP
Power Requirements| Two AA (LR6) alkaline batteries
Battery Life|  20h
Dimensions (HxLxD)| 10.2” x ø2.1”260mm x ø 54mm
Weight| 0.5lb /218g

SAMSON logo Samson Technologies Corp.
278-B Duffy Ave
Hicksville, New York 11801
Phone: 1-800-3-SAMSON (1-800-372-6766)
www.samsontech.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals