truelife X5 BT Pulse Oximeter User Manual
- June 5, 2024
- truelife
Table of Contents
truelife X5 BT Pulse Oximeter featured.
BOX CONTENTS
- 1 × TrueLife Oximeter X5 BT
- 2 × AAA alkaline battery
- 1 × Suspension cable
- 1 × Case
- 1 × Manual
- 1 × Safety instructions
The TrueLife Oximeter X5 BT uses a light source that passes through the tissue and hits a detector that measures its intensity. The Pulse Oximeter X5 BT measures oxygen saturation or blood oxygen levels as well as heart rate
PRODUCT DESCRIPTION
- Battery cover
- Battery cover lock
- Display
- Control button
- Finger clamp
Display Description
- Oxygen saturation symbol
- Oxygen saturation (percentage value)
- Pulse rate waveform
- Battery status symbol / Bluetooth symbol (alternately)
- Heart rate symbol
- Perfusion index
- Pulse rate
- Pulse rate bar
BATTERY INSTALLATION
- Remove the battery cover on the back of the oximeter and insert 2 AAA batteries. Make sure that the batteries are inserted with the correct polarity as indicated in the battery compartment. Do not use batteries after their expiration date.
- If the battery status symbol flashes on the display, the batteries must be replaced.
- When battery power is critically low, the device will not take a reading.
- If you will not be using the device for an extended period of time, remove the batteries.
SETTINGS
- The oximeter offers the possibility to set audible alarms, pulse rate beep and brightness. You can then set the upper and lower limits for the audible alarms.
- To enter settings, turn on the oximeter by pressing the control button. After the display turns on, hold down the control button again for 2 seconds. The display shows the menu for setting the alarms, the pulse rate beep and the brightness. The menu for setting the alarm limits is accessed by holding down the control button while the asterisk is next to „Alm setup“.
- To exit settings, navigate to the line „Exit“ and hold down the control button .
- Setting the measurement alert
- The reading can be accompanied by an audible alert.
- To turn on the alert, scroll to the „Alm“ line and hold down the control button until „on“ is set. To turn off the alert, proceed in the same way and set to „off“.
- Setting audible alarm limits
- When taking a reading, the oximeter starts emitting an audible alarm when one of the measured values is smaller or larger than the set limits.
- To change the limits, enter the alarm limit menu and select the line with the value you want to change. Once you are at your desired value, hold down the control button and the value will change. If „+“ is on the bottom line, the value will rise. If „-“ is there, the value will decrease.
- Note: We recommend that you leave the alarm limits at the preset values.
- Setting the heart rate beep
- The pulse rate can be accompanied by a beep when a reading is being taken.
- To turn on the pulse rate beep, navigate to the „Beep“ line and hold down the control button to change it to „on“. To switch off, proceed in the same way and set to „off“.
- Adjusting the brightness
- The brightness of the oximeter display can be adjusted.
- To change the brightness, navigate to the „Brightness“ line and hold down the control button to set the desired brightness, where „1“ is the lowest and „5“ the highest.
- Factory settings
- If you want to restore factory settings, navigate to the „Restore“ line and hold down the control key. „OK“ will appear on the line and all lines will be returned to their original values.
TAKING A READING
- The measurement process itself is very simple. Follow the instructions below.
- Insert your finger into the finger clamp. Keep your finger still.
- Press the control button. The oximeter immediately starts measuring. Do not move during the measurement process.
- After a few seconds, the reading appears on the display.
- There are 6 different display modes on the device. Use the control button to toggle between them.
- After removing your finger from the clamp, the oximeter will automatically shut off after 10 seconds.
READINGS
TRANSFERRING READINGS TO A MOBILE DEVICE
The TrueLife Oximeter X5 BT allows you to transfer readings to a mobile device and keep them with you at all times. The software automatically saves the measured data and plots the data in the app. Below you will find instructions on how to transfer the data. First, download the application, install and register.
- Download the free application at the link below. The application is intended for mobile devices or other devices running Android or iOS.
- Install and open the application.
- Continue by registering in the application. Fill in your email address and password. This information serves as login information.
SPECIFICATIONS
SAFETY WHEN WORKING WITH THE DEVICE:
- Read the attached safety instructions carefully.
For proper handling of the product, read the latest version of the manual, which is available for download at: www.truelife.eu
Typos and information changes reserved.
Warning: This product is intended for use in households and similar environments. We declare that if the TrueLife Oximeter X5 BT product is used as a professional medical device, a safety inspection (BTK) must be performed regularly at the following intervals months after the purchase of the product, then every 12 months.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>