urmet 1086 Bluetooth Sclak Keypad Installation Guide

June 6, 2024
urmet

Mod. 1086
DS1086-002B-LBT20978
BLUETOOTH SCLAK KEYPAD
Sch./Ref.1086/2

INSTALLATION HANDBOOK

FCC. ID.: REA10862

GENERAL DESCRIPTION

The SCLAK Bluetooth Keypad Ref. 1086/2 is a keypad that allows activation of an electric lock by entering an access code. The keypad is an accessory device that must be associated with a SCLAK Unit Bluetooth relay Ref. 1086/11 present in the system, the keypad is not capable of stand-alone operation.
To associate and configure the keypad it is necessary to use the Urmet SCLAK App (please refer to chapter “KEYPAD ACTIVATION AND CONFIGURATION”).

PACKAGE CONTENTS

  • SCLAK Bluetooth Keypad Ref. 1086/2
  • Package consisting of:
    – Front frame
    – 4 fixing screws for the front frame
    – 2 fixing screws for device base
    – 2 wall plugs
    – Battery type AA / ER14505 3,6 V

COMPONENT DESCRIPTION

  1. Front frame
  2. Numeric keypad
  3. Device base
  4. Housing for battery

INSTALLATION

Remove the numeric keypad from inside the base.

  • Fix the base of the device close to the SCLAK Unit Bluetooth relay Ref. 1086/11 to which the keypad will be associated.

ATTENTION! The SCLAK Keypad Bluetooth device Ref. 1086/2 must be installed near the SCLAK Bluetooth relay unit Ref. 1086/11.

  • Insert the supplied battery into the battery compartment on the rear of the numeric keypad.
  • Position the numeric keypad inside the base.
  • Attach the front frame onto the base of the device.
  • Fasten the front frame by tightening the appropriate screws.

KEYPAD ACTIVATION AND CONFIGURATION

To proceed with the configuration of the SCLAK Bluetooth Keypad the Urmet SCLAK app, available from the Apple store (IOS) or the Play Store (Android), must be downloaded onto a Smartphone connected to the Internet via its own mobile data connection or via WiFi.
The Urmet SCLAK app can be downloaded onto your smartphone by scanning the following QR Code.

http://app.sclak.com/download

ATTENTION! A SCLAK unit Bluetooth relay device must be present in the system Ref. 1086/11 which is active and configured.
The association of the keypad to a SCLAK Unit Bluetooth relay is possible if the operator is a SCLAK Installer or Administrator.
Follow the steps below to configure and associate the SCLAK Bluetooth Keypad to a SCLAK Unit Bluetooth relay.

  1. Activate Bluetooth on your smartphone, start the Urmet SCLAK app and log in with an installer or administrator type account in which the SCLAK Unit Bluetooth relay device is active and configured.
  2. After entering your details, press the “Log in” button.
  3. On the following screen select the SCLAK Unit Bluetooth relay device to which the keypad will be associated
  4. Press on the SCLAK Unit Bluetooth relay device icon.
  5. On the following screen in the “ACCESSORIES” section press the “Add accessory” button.
  6. Follow the steps outlined in the App to add and configure the SCLAK Bluetooth Keypad.

REPLACING THE BATTERY

  1. Remove the front frame by loosening the appropriate screws.

  2. Remove the numeric keypad from the device base.

  3. Rotate the numeric keypad and replace the low battery, from the battery compartment, with another battery of the same size (type AA / ER14505 3,6 V ) observing the correct polarity.
    Use only batteries that comply with the safety standard IEC 60086-4: 2014 Primary Batteries –
    Part 4: Lithium Battery Safety.
    ATTENTION! Risk of explosion if the battery is replaced with a type other than that indicated.
    Dispose of used batteries according to local regulations.

  4. Position the numeric keypad inside the base.

  5. Re-attach the front frame by tightening the appropriate screws.

TECHNICAL FEATURES

Power supply: ………………………………………………………………….. Battery type AA / ER14505 3,6 V 2,6 Ah
Connection: ………………………………………………………………………………………………… Bluetooth 4.0 or higher
Frequency band: ……………………………………………………………………………………………2402 MHz ÷ 2480 MHz
Output power (Max): …………………………………………………………………………………………………………… 3,4 dBm
Housing protection rating: ………………………………………………………………………………………………………….IP65
Operating temperature: ………………………………………………………………………………..-20° ÷ 60°C / -4 ÷ 140 °F
Dimensions (LxAxP) ……………………………………………………………….. 84 x 84 x 27 mm / 0,27 x 0,27 x 0,08 ft

KEY TO SYMBOLS

Symbol

|

Description

---|---
| Direct input voltage
| See the installation manual of the device

SIMPLIFIED EU DECLARATION OF CONFORMITY

Hereby, URMET S.p.A. declares that the radio equipment type:
BLUETOOTH SCLAK KEYPAD Ref. 1086/2 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: www.urmet.com

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept all interference received, including interference that may cause undesired operation.

15.105 Information to the user statements:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 4 July 2012 on waste electrical and electronic equipment (WEEE)
The symbol of the crossed-out wheeled bin on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and electronic equipment.
The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment.
For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

DS1086-002B

URMET S.p.A. 10154 TORINO (ITALY)
VIA BOLOGNA 188/C
Telef. +39 011.24.00.000 (RIC. AUT.)
Fax +39 011.24.00.300 – 323

|

LBT20978

Area tecnica servizio clienti +39 011.23.39.810
http://www.urmet.com
e-mail: info@sclak.com

---|---

MADE IN ITALY

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals