urmet H.265 Series IP Camera User Guide
- June 10, 2024
- urmet
Table of Contents
H.265 Series IP Camera User Guide
General information
Dear Customer,
Thank you for purchasing this product.
This quick start guide was written to help you set up H.265 IP Camera Series
rapidly and easily.
Read this quick start guide which contains information for correct, safe use
carefully before using the device.
Keep this guide at hand so that you can refer to it when needed.
*NOTE
For more detailed information about the devices, refer to the complete user
manual available on the Unmet website (see QR code printed on the Addendum
sheet).
WARNINGS
Electricity
Before connecting to electrical outlet, verify the electrical
specifications of the device are suitable for the available power source.
We suggest to connect the device to electrical outlet via a switch
disconnector.
In case of malfunctioning, disconnect electrical power from the general
switch.
Use only the provided power supply.
Safety precautions
Do not expose the device to rain or humidity and do not insert any solid or
liquid object in it to prevent the risk of fire or electrocution. In these
events disconnect the device from the electrical outlet and call technical
assistance to check it.
Do not open the device. Any repair must be made by qualified personnel or by
calling the nearest authorized technical assistance center
(www.urmet.com >> Contacts).
Keep the device away from children to prevent any, even involuntary, damaging.
Do not touch the device with wet hands as it might cause electrical shock or
mechanical damages.
If the device falls down while working or if the sales box is damaged, do not
continue using it. If usage is continued under such circumstances electrical
shocks might take place.
Contact the authorized retailer or installer.
Installation precautions
Before installing the camera, check its technical specifications to ensure
that the IP rating is suitable for the environment in which it will be
mounted. The IP rating is only guaranteed if the product is installed
correctly.
Do not point the camera directly to sunlight or other intense sources of
light, even when turned off. The subject of recording must not be against the
light.
Do not point the camera against reflective objects.
Some light conditions (such as fluorescent color) can affect the recorded
colors. Use AUTO-IRIS lens when operating the camera in changing light
environments.
Do not use this device on any unstable support such as lurching or sloping
table to prevent the device from falling and be damaged.
If water or any other material should penetrate the camera, stop using it as
it might cause fire or electrical shock and contact the authorized retailer or
installer.
Do not cover the device with any cloth while using to prevent deformation of
the external part and inner components heating which might provoke fire,
electrical shock or mechanical damages.
Do not put magnets or magnetized objects close to the device to prevent
functional anomalies.
Do not use this device in presence of smoke, steam, humidity, dust or intense
vibrations. Do not use the device shortly after moving it from warm to cold
environment and vice versa. After moving the device wait three hours before
using it:
this time is necessary for the device to adapt to the new environment
(temperature, humidity, etc.).
Usage precautions
Check the device is not damaged after removing the packaging.
Check the working environment is not too humid and the temperature is within
the indicated range.
Do not point the camera against sunlight to prevent sensor damages.
Device cleaning
Use a dry cloth to remove dust and dirt from the device.
If dirt cannot be removed with a dry cloth, use a humid cloth and a neutral
cleanser.
Do not use spray cleanser for device cleaning. Do not use volatile liquids
such as gasoline, alcohol, solvents etc. or chemical treated cloth to clean
the device to prevent deformations, damages or scars on the finishing paint.
Disconnect the device from the electrical outlet before cleaning.
Video recording
This device is not designed as a burglar system but mainly to transmit and
record video images. URMET S.p.A. is not in any way responsible for loss or
damages of the user consequent to theft.
Before using the device, record a demo video to verify the correct
functionality of this feature. URMET S.p.A. is not in any way responsible for
loss of recorded data consequent to wrong setting or usage, device
malfunctioning or failure.
This device is composed by electronic precision components. Do not hit the
device while recording as it might affect the video.
Privacy and Copyright
The IP camera is designed for surveillance systems. Video recording is subject
to the laws applicable to the Country where used. It is forbidden to record
images with Copyright.
The User is responsible to check and respect all local laws and norms for
video signal recording. The manufacturer is NOT in any way liable for any
usage of the product which might result not compliant to the relevant norms.
Firmware upgrade
Contact Customer Service Technical Assistance URMET S.p.a. in order to check
availability of firmware upgrades.
Network configuration
Camera default setting is DHCP mode. If the network does not support dynamic addressing (DHCP), the device will automatically switch to factory IP 192.168.1.168. Use Rumer “Device Config. Tool” software in order to modify the IP address and other network settings to prevent any conflict with other devices on the network.
Network connections
When connecting a PC (using Software Client or Browser), any video channel on
the PC will be using “unicast” connection (TCP, RTP, UDP).
The device can support up to 10 “unicast” connections so it is possible to
show the video on maximum 10 remote devices (PC or smartphone) at the same
time depending on the available network band.
Installation
INSTALLATION OF BULLET CAMERAS
Ceiling Mounting
Insert three expansion bolts in place into the ceiling and fix the equipment
with three locking screws
Wall Mounting
Insert three expansion bolts in place into the wall and fix the equipment with
three locking screws.
SD Card Installation
SD Card installation model 1099/208A
ATTENTION: this operation must be carried out by qualified personnel.
INSTALLATION OF MINI DOME CAMERAS
Ceiling Mounting
- Paste the sticker in place at the proper position as selected.
- Remove the collar off the camera by rotating it down.
- Fix the pedestal by drilling locking holes around the sticker and inserting three expansion bolts into the holes and fastening it with three locking screws.
- Adjust it to an appropriate angle.
- Mount the collar back by rotating it up.
SD Card Installation
MINI FLAT CAMERA INSTALLATION
Ceiling fixing
- Fasten the fixing bracket to the ceiling.
- Fasten the camera body to the ceiling.
- Correctly adjust the angle by rotating the camera body.
- Apply the dome cover of the camera
SD Card installation
INSTALLATION OF VANDAL-PROOF DOME CAMERAS
Ceiling Mounting
- Paste the sticker in place at the proper position as selected.
- Remove the front component by loosening the three locking screws with a screwdriver.
- Fix the pedestal by drilling locking holes around the sticker and inserting four expansion bolts into the holes and fastening it with four locking screws. Adjust it to an appropriate angle.
- x the front component on the pedestal by tightening the three locking screws.
SD Card Installation
IP Camera Configurations
The camera must be configured for the home or office network after it has been
powered.
It is advisable to install and configure one camera at a time if you are
installing multiple cameras on the same network.
CONNECTION TO IP NETWORK WITH DHCP SERVICE
For Quick installation about IP camera with dynamic host configuration (DHCP)
on the network will be assigned an IP address automatically. IF DHCP Service
is not supported, the default IP Address of IP Camera will be 192.168.1.168.
IP Camera Configuration:
- Install the Software “Device Config. Tool” software, available for download at www.urmet.com. on the product page and by selecting the DOCUMENTATION AND RESOURCES section.
- Launch the “Device Config. Tool” Software, selecting it will be displayed automatically IP Address, Subnet Mask, Gateway, and MAC Address for each IP Camera detected in LAN, as shown in picture below.
If the searched IP address and PC IP address are not in the same network
segment, user may modify IP address, subnet mask, and other parameters of IP
camera by using “Device Config. Tool” software.
First select the device to modify IP address and then input new IP address,
subnet mask, gateway and username/password. Insert the password and click
“Modify” button to change IP address of the device.
*IMPORTANT NOTE: IP camera Default Settings Default Static IP
Address:192.168.1.168
Username: admin
Password: admin (only for firmware versions prior to V.8.2.2)
Media port: 9000
3. Before using IE (Internet Explorer) browser to access the IP camera for
the first time, related plug-in components must be installed by following the
procedure below:
Access IP address of the IP camera for installing plug-in only for the first
time. In the Web Page opened select “Download”, after that select “Run” in the
pop-up below
- Wait for plug-in download, after that confirm the ActiveX Installation.
- Select “Install” and wait for the installation is completed.
4. After completed the Active X installation, close the Internet Explorer Web
Page and launch it again, put the IP Camera Address.
5. Open the browser and enter the camera’s IP address
(http://192.168.1.168) and the window for creating the Administrator
password will appear. It is necessary to set the password immediately to
protect your privacy. The password should contain a combination of 8 to 15
characters meets the required security criteria.
Make a note of the password and keep it in a safe place.
6. Confirm with OK button. At this point, another window will appear where the user can choose and configure how to recover his password if the user loses it.
7. Security Question Configuration: choose one of the proposed questions and
fill in the corresponding answer.
Certificate of authorization: it will be possible to export a certificate that
can be used to set the password again using the password recovery function.
Super code: enabling this function, it will be possible to contact Unmet
Customer Service to request a Super Code that will allow the user to set a new
password using the recovery password function.
Once the options have been selected, confirm with OK.
At the end of the password change process, the following window will appear.
Confirm with the OK button. If no password recovery method is chosen, in the
event of a lost password, it will be necessary to act directly on the RESET
button (located on the camera), thus returning the camera to its factory
parameters.
The LOGIN screen shown below will now appear:
8. Select “Login” in order to enter in LIVE screen.
9. Click the buttons on the top left corner in the Web Page to select the
stream to display (Main Stream, Sub Stream or Mobile Stream)
PTZ CONTROL
(PTZ control) select the icon to open the following window:
On Autofocus cameras, the PTZ interface will be as follows:
Option | Value | Explanation |
---|---|---|
Zoom | Step/-/+ | Manually adjusts zoom (+ zoom in / – zoom out) Step: defines |
zooming speed
Focus| Steph /-/+| Manually adjusts focus (+ increase / – decrease) Step:
defines focusing speed
Auto Focus| /| Adjusts focus automatically
Restore| /| Resets PTZ interface default settings (including focus)
Refresh| /| Updates the PTZ interface with changes to parameters (including
focus)
PLEASE NOTE
For more details and technical details on programming (e.g. video analysis
algorithms), setting (e.g. image controls) and configuration (e.g. user
privilege management) please refer to the camera’s technical manual.
CORRECT DISPOSAL OF THIS PRODUCT
DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 4 July
2012 on waste electrical and electronic equipment (WEEE)The symbol of the
crossed-out wheeled bin on the product or on its packaging indicates that this
product must not be disposed of with your other household waste.
Instead, it is your responsibility to dispose of your waste equipment by
handing it over to a designated collection point for the recycling of waste
electrical and electronic equipment.
The separate collection and recycling of your waste equipment at the time of
disposal will help to conserve natural resources and ensure that it is
recycled in a manner that protects human health and the environment.
For more information about where you can drop off your waste equipment for
recycling, please contact your local city office, your household waste
disposal service or the shop where you purchased the product.
http://qrcode.urmet.com/default.aspx?pagUrmet=reteCommercialeEN
For assistance and information about Unmet products and systems you can scan
this QR code with your smartphone or visit
www.urmet.com >> Contacts >> Export Sales Network
Unmet Spa. reserves the right to make changes to its products at any time,
without prior notice. www.urmet.com | info@urmet.com
All Unmet products bear the mark Made in China to Urmet specifications.
Customer Care
Italia: 011 23 39 810
Export Dept.: +39 011 24 00 250/256
URMET S.p.A.
Via Bologna, 188/C | 10154 Torino (ITALY)
www.urmet.com |
info@urmet.com
IF YOU LOVE YOUR BUILDING
Documents / Resources
|
urmet H.265 Series IP
Camera
[pdf] User Guide
VK 1099-463, VK 1099-464, VK 1099-403, VK 1099-402, H.265 Series IP Camera, IP
Camera, Camera
---|---
References
- BfDI - Startseite
- BfDI - Startseite
- Startseite | Grothe
- Startseite | Grothe
- Professional Video Door Phone and Intrusion Alarm Systems | Urmet SpA
- Professional Video Intercom and Intrusion Alarm Systems | Urmet SpA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>