urmet NVR NEIUS SERIES Video Recorder User Guide

June 8, 2024
urmet

Quick guide
NVR NEIUS SERIESurmet NVR NEIUS SERIES Video Recorder
-

General Information

Dear Customer,
Thank you for purchasing this product.
This document describes how to quickly install and use the URMET S.p.A. S+265/H.265/H.264 series NVR models. Before using the device, read this document carefully and keep in a safe place where it is easily accessible for reference when needed.
*NOTE
For further information, see the instruction manual on the Urmet website. To download the manual from the site, see the QR code on the Addendum sheet.
WARNINGS
Power supply
Before connecting the device to the electrical outlet, ensure that the ratings on the nameplate match those of the mains power supply.
Do not pull on the cable to unplug the device.
Switch off the device before disconnecting the power. Do not switch the NVR off while recording or playing, or from the configuration menu. Stop recording and playback before disconnecting the device, to prevent damage to the hard disk.
Safety precautions
Keep the device away from rain and dampness to prevent the risk of fire or electrocution. Do not introduce any material (solid or liquid) inside it. If this should accidentally occur, disconnect the device from the mains outlet and have it inspected by qualified personnel.
In all cases, contact qualified personnel or an authorised service centre for repairs (www.urmet.com >> Contacts >> Technical Support Centres).
Keep the device away from children, to avoid accidental damage.
Do not touch the device with wet hands to prevent electric shock or mechanical damage.
Stop using the device if it falls or if the external casing is damaged. Continuing to use the device in these conditions could cause electric shock. Contact the retailer or authorised installer.
Installation precautions
To prevent the device from overheating, place it in a position that allows a flow of air through the vents in the casing. Leave a space of at least 5 cm when installing in a rack. For the same reason, do not install near heat sources such as radiators or hot air ducts.
Keep the device away from direct sunlight. Do not install in areas subject to excessive dust, mechanical vibration or shock.
Do not place the device on an unstable surface, such as an unsteady or sloping table, as the device could fall, causing damage or mechanical failure.
Do not install the device where it may be exposed to moisture or water. Do not spray water on the device, to avoid risk of fire, electric shock or mechanical damage.
Stop using the device if water or any other material penetrates inside it, to prevent risk of fire or electric shock. In such cases, contact the retailer or authorised installer.
Do not place heavy or heat-generating objects on top of the device: this could damage the casing and/or increase the internal temperature, leading to damage.
Do not cover the device with a cloth while it is running to prevent deforming the external casing and overheating the internal parts, causing risk of fire, electrocution and mechanical failure. Keep magnets and magnetised objects away from the device to avoid malfunction. Do not use the device in the presence of smoke, vapour, humidity, dust or intense vibrations.
Do not operate the device immediately after moving it from a cold place to a warm place or vice versa.
Wait for around three hours: this will allow the device to adapt to the new ambient (temperature, humidity, etc.).
Cleaning the device
Rub gently with a dry cloth to remove dust and dirt.
Dip the cloth in a neutral detergent if dirt cannot be removed with a dry cloth alone.
Do not use spray products to clean the device. Do not clean the device using volatile liquids (such a petrol, alcohol, solvents, etc.) or chemically treated cloths to prevent deformation, deterioration or scratches to the paint finish.
Disconnect the device from the electrical outlet before any cleaning or maintenance operations.
Hard Disk
The hard disk installed in this device is sensitive to shock, temperature changes and vibrations. Failure to adopt suitable precautions could compromise the proper functioning of the device and cause loss of data from the hard disk.
If repairs are required, it is advisable to backup all important data before taking the device to the service centre. Urmet S.p.A. is not liable for the loss of stored data.
Hard disks must be installed by qualified technical personnel or by contacting the technical support centre.
Image recording
This device was designed to record images. It is not a burglar alarm. URMET SpA cannot be held liable for loss or damage due to theft suffered by the user.
Make a test recording before using the device to ensure that it is working properly. URMET SpA is not liable for loss of stored data due to loss or damage caused by failure to follow the instructions for installation and use, improper use or malfunctioning of the device. This device contains precision electronic components. Protect the device from shocks to ensure proper image recording.
Privacy and Copyright
The NVR is a device for CCTV systems. The recording of images is subject to the laws in force in the country of use. Recording of images protected by copyright is forbidden.
Product users are responsible for checking and complying with all local rules and regulations regarding monitoring and the recording of video signals. The manufacturer SHALL NOT BE LIABLE for any use of this product not in compliance with the laws currently in force.
Software upgrade
Regularly check the specific section of the manufacturer’s website at www.urmet.com in the page
dedicated to the product under the section DOCUMENTATION AND RESOURCES.
Firmware upgrade
Contact URMET SpA Customer Service to check the availability of firmware upgrades.
Network configuration
By default, the NVR is set with a static IP address 192.168.1.3.
Using the NVR OSD menu, assign the NVR an IP address that has not already been assigned to other devices, in order to avoid network conflicts.
After assigning an appropriate address to the NVR, it can be connected to the network.
By opening the web page of the device from Internet Explorer you will be asked to change the password which by default is “admin” (login user “admin”). It is recommended that you always customize your password.
To detect the device on the network and perform the basic configurations, use the SearchConfig Tool V2.0 software available for download on the website www.urmet.com in the page dedicated to the product under the DOCUMENTATION AND RESOURCES section.

Installing the HDD

Schematic diagrams for installing the standard NVR HDD:

  1.  Remove the screws on the rear and sides of the chassis and then remove the top cover.urmet NVR NEIUS SERIES Video Recorder - remove the top cove
  2. Connect one end of the HDD data cable to the SATA interface of the NVR mother board, and the other end to the HDD.urmet NVR NEIUS SERIES Video Recorder - other end to the HDD
  3. Connect one end of the HDD power cable to the interface of the NVR mother board and the other end to the HDD.urmet NVR NEIUS SERIES Video Recorder - mother board
  4. Tighten HDD screws on the bottom of the NVR chassis, attach the top cover and fix it with screwsurmet NVR NEIUS SERIES Video Recorder - fix it with screws

Schematic diagrams for installing the front NVR

Attach the HDD mounting screws and insert it into the related HDD slot on the front panel.

urmet NVR NEIUS SERIES Video Recorder - slot on the front
panel

Startup

Make sure that the power supply required by NVR is used, NVR is well grounded, and NVR video output is well connected to the monitor before start up.
Connect the power supply and turn on the power switch on the rear panel. The device starts.
Default username: admin, Password: to be customized

Initializing HDD

Select “Main Menu -> System Settings -> Disc Manager” to enter the Disc Manager interface, where you can select the HDD to set for initialization.

Modifying the IP Address of the Device

Select “Main Menu -> System Settings -> Network Settings” to enter the Network Card setting interface, where you can modify IP addresses and perform other operations.

Adding a Digital Channel

Select “Main Menu -> Channel Manager -> Channel Configuration -> Basic Configuration” and click the Search button to start automatic searching. The Search button changes to Stop button. You can click the Stop button to stop searching.
Select the IPC to add after searching finishes and click Add or double click IPC to add.
After adding, the Added Devices list displays the added IPC. If the connection status is displayed as “ ”, addition is successful; if the connection status is displayed as “ ”, addition fails. In the latter case, check the network connection or check if it is added correctly.

urmet NVR NEIUS SERIES Video Recorder - preview this
channel

Click “ ” in the Added Devices list to preview this channel.
Click “ ” in the Added Devices list to re-edit channel information.

Playback

Select “Main Menu -> Playback” to enter the Playback interface, where you can select the video to playback according to video type.

urmet NVR NEIUS SERIES Video Recorder - select the
video

Mobile Monitoring

In preview mode, move your cursor over the bottom of the screen to display the task bar. Click the mobile monitoring icon “ ” to enter the mobile monitoring interface, where you can scan the first QR code to download the client and then the ID QR code to obtain the ID for video preview and other operations.

urmet NVR NEIUS SERIES Video Recorder - preview and
other

Remarks:
The mobile monitoring feature is unavailable for some products. The real product shall prevail.

Shutdown

Select “Main Menu -> ****” and click “Shutdown”. In the message window, click “Yes” to shut down.

Notes:

  1. Do not cut off the mains power when the system is displaying “Shutting the system down…”.
  2. Do not cut off the mains power when the system is operating

**** DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 4 July 2012 on waste electrical and electronic equipment (WEEE).
The crossed-out wheeled bin symbol on the product or on its packaging indicates that the product must not be disposed of together with ordinary household waste.
The user must therefore dispose of the waste equipment by taking it to a designated collection centre for the recycling of waste electrical and electronic equipment. As an alternative to independent disposal, you can hand in the equipment you wish to dispse of to the retailer when purchasing a new appliance of the same type.
Electronic products up to 25 cm in size can also be handed in for free disposal, with no purchase obligation, at electronics stores with sales areas of over 400 m2.
Adequate separate collection for recycling, treatment and environmentally friendly disposal of the scrapped equipment helps to prevent negative impacts on the environment and on human health, and promotes recycling and/or reuse of the materials with which the equipment is made.

Customer Care
Italia: 011 23 39 810
Export Dept.: +39 011 24 00 250/256
URMET S.p.A.
Via Bologna, 188/C 1 10154 Torino (ITALY)
www.urmet.com info@uimet.com
IF YOU LOVE YOUR BUILDING NVR NEIUS & NEIUS PLATINUM
S+265/H.265/H.264
1-2-4-8 HDD
5-10-20-40-80 CH
6-8-12MP
MADE IN CHINA
To Urmet specification

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals