urmet 108611 Bluetooth Relay Installation Guide

DS1086-003A

Mod. 1086
LBT20871

BLUETOOTH SCLAK UNIT RELAY (WITH SCLAK UNIT 2VOICE VOLTAGE ADAPTER)

Sch./Ref.1086/11

 INSTALLATION HANDBOOK
**FCC. ID.: REA108611

**

GENERAL DESCRIPTION

The SCLAK Unit Bluetooth Relay Ref. 1086/11 makes it possible to transform any electric lock or automation system into an integrated access control system managed by smartphone using Bluetooth 4.0 technology.

The device is compatible with all-electric, electromagnetic, electromechanical locks and does not require any internet connection to operate.

The SCLAK Unit Bluetooth relay works with all smartphones running IOS 8 or higher or Android 4.3 or higher.

PACKAGE CONTENTS

• SCLAK Bluetooth Relay Unit Ref. 1086/11
• Activation code
• Installation handbook

COMPONENT DESCRIPTION

1. Status led
2. Front cover
3. Cable with wires for connection to the system
4. 6-way connector for connecting to the cable with wires
5. Jumper (JP1)
6. Jumper (JP2)
7. Jumper (JP3)
8. Jumper (JP4)

DESCRIPTION OF THE STATUS AND LED THE WIRES IN THE CABLE FOR CONNECTION

TO THE SYSTEM

Status led

(*) The switch-off time of the status LED is the same as the door opening time set in the configuration phase

Wires in the cable

 INSTALLATION

 INSTALLATION METHOD

WARNING! Insert the SCLAK Unit Bluetooth relay Ref. 1086/11 inside the flush-mounted box of the push button panel.

Below is the procedure for installing the device in an ALPHA call station.

• Remove the base of the device by unscrewing the rear screws.

• Set the jumpers of the device according to the system in which it will be installed. Refer to the chapter “Description of the jumpers”.

•  Reinsert the base of the device and tighten the rear screws.

• At the call station, remove the frame heads using a flat screwdriver and then turn the frame over.

• Position the SCLAK Unit Bluetooth relay Ref. 1086/11 inside the flush-mounted box.
  ATTENTION! Maximum signal range in the open air: 15 m. Walls, obstacles, and metal containers reduce the range.

• Make the connections to the terminal board according to the type of lock. Refer to the chapter “Wiring diagram”.
  Wires with a cross-section area of 0.5 mm² or larger must comply with IEC 60332-1-2; wires with a cross-section area smaller than 0.5 mm² must comply with IEC 60332-2-2.
  After making the connection, the status LED will start flashing to indicate that the device is powered and is awaiting configuration.

• Close the panel frame and tighten the closing screws.

DESCRIPTION OF THE JUMPER

JP1 Jumper
The JP1 jumper on the inside of the front cover allows the device relay to be set as a normally open contact (NO) or as a normally closed contact (NC).

JP2 Jumper
The position of jumper JP2 in a closed position allows you to bring the positive power supply to a relay contact (white wire).

JP3 and JP4 Jumper
The position of the jumpers JP3 and JP4 allow you to select the type of power supply:

•  2-wire 2Voice system (48V )
• With a local power supply from 12 ÷ 24 V⋍ (with these power supplies a cable shorter than 3m must be used and power the device with less than 15 watts of power)

DEVICE ACTIVATION AND CONFIGURATION VIA THE SCLAK APP

To proceed with activation and configuration of the SCLAK Unit Bluetooth Relay Ref. 1086/1, the Urmet SCLAK app, available from the Apple store (IOS) or the Play Store (Android), must be downloaded onto a Smartphones are connected to the Internet via their own mobile data connection or via WiFi.
The app can be downloaded onto your smartphone by scanning the following QR Code.

http://app.sclak.com/download

After downloading and installing the app, follow the device activation procedure indicated on the Urmet SCLAK app. For further details on the activation of the SCLAK Unit Bluetooth relay Ref. 1086/11 refer to the SCLAK website under “Products / Installation and activation / Enable SCLAK / See instructions” or scan the following QR Code with your smartphone camera.

http://qrcode.urmet.com/default.aspx?sito=sclak&pagSclak=attivaSclak&lingua=en

TECHNICAL FEATURES

Supply voltage: ………………………………………………………………………………………………. 48 V or 12 ÷ 24 V⋍
Maximum power: ……………………………………………………………. Max 0,4W @ 48 V or Max 0,3W @ 24 V⋍
Relay output (white and brown wires ):. …………………………………………………………………………. 1 A @ 24 V⋍
Frequency : ……………………………………………………………………………………………………………………….. 50/60Hz
Connection: ………………………………………………………………………………………………… Bluetooth 4.0 or higher
Frequency band: ……………………………………………………………………………………………2402 MHz ÷ 2480 MHz
Output power (Max): …………………………………………………………………………………………………………… 6,6 dBm
Housing protection rating: ………………………………………………………………………………………………………….IP44
Operating temperature: ………………………………………………………………………………..-20° ÷ 60°C / -4 ÷ 140 °F
Dimensions (LxHxD): ……………………………………………………………… 55 x 55 x 20 mm / 0,18 x 0,18 x 0,06 ft

KEY TO SYMBOLS

SIMPLIFIED EU DECLARATION OF CONFORMITY

Hereby, URMET S.p.A. declares that the radio equipment type: BLUETOOTH SCLAK UNIT RELAY Ref. 1086/11 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: www.urmet.com
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept all interference received, including interference that may cause undesired operation.

15.105 Information to the user statements:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

 SCHEMI DI COLLEGAMENTO / WIRING DIAGRAMS

Connecting a SCLAK Unit Bluetooth Relay device Ref. 1086/11 to a standard electric lock or to an electromechanical lock

SV124-1358

Connection of a SCLAK Unit Bluetooth relay device Ref. 1086/11 in 2Voice systems
DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 4 July 2012 on waste electrical and electronic equipment (WEEE)

The symbol of the crossed-out wheeled bin on the product or on its packaging indicates that this product must not be disposed of with your other household waste.

Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment.

For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

DS1086-003A
URMET S.p.A.
10154 TORINO (ITALY)
VIA BOLOGNA 188/C
Telef. +39 011.24.00.000 (RIC. AUT.)
Fax +39 011.24.00.300 – 323

LBT20871
Area tecnica
servizio clienti +39 011.23.39.810
http://www.urmet.com
e-mail: info@sclak.com
MADE IN ITALY

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>