urmet 1099/218 3.6mm 2MP Bullet Camera for WiFi Kit User Guide

: June 8, 2024
: urmet

Table of Contents

urmet 1099/218 3.6mm 2MP Bullet Camera for WiFi Kit
Precautions
Technical specifications
Installation specifications
OPERATING FEATURES
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

urmet 1099/218 3.6mm 2MP Bullet Camera for WiFi Kit

Precautions

Make sure that the device is intact after removing it from the package.
Disconnect the device from the mains before cleaning or maintenance. Do not use spray products to clean the device.
Check that the working temperature is within the indicated range and that the environment is not particularly humid.
If installed in outdoor, don’t expose it to direct rain or high temperatures.
Disconnect power by means of the circuit breaker in the event of a failure and/or bad operation.
The device can only be opened by qualified technical personnel.
Exclusively contact an authorised service centre for repairs.

Technical specifications

Sensor type: 2.0 MegaPixel 1/2.7” Color CMOS
Sensitive elements: 1920 pixel (H) x 1080 pixel (V)
Lens: 3.6 mm
Resolution: 1080p@15fps
IR CUT FILTER: YES
Synchronization: Internal
Shutter control: 1/25 ~ 1/10.000 sec (AUTO)
Back-lighting compensation: AUTO
White balancing: AUTO
Gain control: AUTO
Sensitivity: 0,03 Lux @(F1.2,AGC ON) – 0 LUX IR ON
LED number: 10pcs
Range: 12 m
Power supply: 12 VCC (+−10%)
Max consumption: ≤ 5.52W
Connectors: Connectors: Power jack + button for pairing camera to WiFi NVR
Protection grade: IP66
Operating temperature range: -10 to +50°C
Dimensions (Ø x L): 69.3 x 142.3 mm
Weight: 345 gr

Important note: Technical features may be changed without prior notice.
ACCESSORIES PROVIDED: Instruction manual.
Important note: Accessories may be changed without prior notice.

SIMPLIFIED EU DECLARATION OF CONFORMITY

Hereby, URMET S.p.A. declares that the radio equipment type: camera 1099/218 is in compliance with Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following internet address: www.urmet.com

Installation specifications

Avoid pointing the lens directly towards the sun or intense sources of light also when the camera is off. The subject must not be backlight.
Do not point the camera towards reflecting objects.
Some lighting systems (e.g. coloured fluorescent lights) may false the colours.
Arrange a suitable circuit breaker and fuse upstream of the devices.
Make sure that the rating plate data correspond to the power specifications before connecting the device to the mains.

INSTALLATION

1. Make sure that no units are powered before starting the installation procedure.
Position the bracket in order to point it to the direction useful to capture images; it is possible to adjust the camera on HORIZONTAL, VERTICAL and TRANSVERSAL axes.
Adjustments
Loosen the screws with the supplied allen wrenches in order to move the bracket in any direction:
- position the bracket on horizontal, vertical and transversal axes
- point the camera in the desired direction. Once made, firmly block.
- Important note: In order to avoid serious damages to the connection cable, avoid rotating repeatedly and excessively the camera fixed to the bracket.
Position the wireless cameras in required installation point and power them. Then pair a free channel of the WiFi NVR.
In order to prevent loss of video signal, it is advisable to install the cameras and orient the aerials so as to guarantee a stable wireless signal indication of at least two lines for each camera on the video stream shown on the NVR.
If the camera is not automatically detected by the NVR, proceed with the manual pairing procedure on the NVR menu by pressing the button corresponding to the channel to be paired and then pressing the pairing button on the camera within 10s.

Important note: For more information, refer to the instructions manual or quick guide of the NVR on the Urmet website. To download the manual or quick guide of the WiFi NVR from the website, see the QR code on the quick guide of the WiFi kit.

OPERATING FEATURES

IR LED operation
The device is provided with a CDS sensor that switches the IR LEDs on when the light is approximately 5 Lux. The deterrent functions (white LEDs and acoustic alarm activation) can be activated manually from the NVR OSD or through the iUVSPro App.