Kruger Matz KM0460 Mobile Phone User Manual
- June 6, 2024
- Kruger Matz
Table of Contents
- SAFETY WARNING AND ATTENTIONS
- PRECAUTIONS.
- PRODUCT DESCRIPTION
- BUTTONS’ FUNCTION
- GETTING STARTED
- BATTERY, SIM CARDS, AND MEMORY CARD INSTALLATION
- INGRESS PROTECTION RATING
- CHARGING
- OPERATION
- CLEANING
- TROUBLESHOOTING
- SPECIFICATION
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
IT’S YOUR LIFE, JUST TAKE I
Mobile phone
KM0459/KM0460
IRON 2
Owner’s manual
Please read this manual carefully before first use and keep it for future reference.
SAFETY INFORMATION
Please take measures as follows to avoid your phone from unauthorized use (e.g. Set PIN code for SIM card).
SAFETY WARNING AND ATTENTIONS
-
ROAD SAFETY
Do not use a hand-held phone while driving. Use hands-free fittings when calls are unavoidable while driving. In some countries, dialing or receiving calls while driving is illegal! -
SWITCH OFF IN AIRCRAFT
Wireless devices can cause interference in aircraft. Using a mobile phone in- flight is illegal and risky. Please make sure that your mobile phone is powered off in flight. -
SWITCH OFF BEFORE ENTERING RISKY AREAS
Strictly observe the relevant laws, codes, and regulations on the use of mobile phones in risky areas. Turn off your mobile phone before entering a place susceptible to explosions, such as an oil station oil tank, chemical plant, or a place where a blasting process is underway. -
OBSERVE ALL SPECIAL REGULATIONS
Follow any special regulations in force in any area such as hospitals and always switch off your phone whenever it is forbidden to use it or, when it may cause interference or danger. Properly use your phone near medical apparatuses, such as pacemakers, hearing aids, and some other electronic medical devices, as it may cause interference to such apparatuses. -
INTERFERENCE
The conversation quality of any mobile phone may be affected by radio interference. -
QUALIFIED SERVICE
Only qualified personnel may install or repair phone equipment. Installing or repairing the mobile phone on your own may bring danger and will violate the warranty rules. -
ACCESSORIES AND BATTERIES
Use only approved accessories and batteries. -
EMERGENCY CALLS
Prior to dialing the emergency number, ensure the phone is switched on and in service.
Note: the device may not necessarily support all the features, due to network or radio transmission problems. Do not rely solely on the mobile phone for critical communications such as first aid. Please consult the local network operator.
PRECAUTIONS.
- Keep the mobile phone and all its accessories beyond children’s reach.
- Ensure the battery cover, lock screw, earphone, and USB rubber plugs are perfectly closed while using near water, or in a humid environment, to ensure the phone remains waterproof and dustproof.
- Do not use or store the mobile phone in a high-temperature place. Protect the device from sources of heat and direct sunlight.
- Always do a backup of important data stored on the phone. The producer does not claim liability for any data loss.
- The producer does not claim responsibility for damages caused by inappropriate use and handling of the device.
PRODUCT DESCRIPTION
1. Earphone jack | 8. |
---|---|
2. Torch button | 9. Microphone |
3. Volume control buttons | 10. Micro USB port (charging) |
4. Confirmation button | 11. Torch |
5. Left function button | 12. Receiver |
6. Right function button | 13. Camera |
---|---|
7. | 14. Speaker |
BUTTONS’ FUNCTION
Button | Function |
---|---|
**** | Right function button: Back – turns back to the previous page; |
press when on the main screen to open the phone book.
**| D i a l button: answers and dials calls
**| End button: ends call Press and hold to turn on/off the phone.
**| Left function button: goes to the main menu
**| Confirmation button: press the button to approve/confirm It Goes
to the main menu and other phone functions. In the calculator app, press to
show the result.
**| Navigational buttons
** Navigational buttons work in 4 directions (functions available when
on the main screen):
• [B]: language selection
• [A]: profile selection
• [D]:
• KM0459: FM radio
• KM0460: browser
• [C]: audio player
*``**
| „ *** ” button:* press and hold to lock the keyboard Press the left function button, then press the „” button to unlock the keyboard.
**#**
| „ # ” button: when on the main screen, press to change between profiles (meeting/silent). In the calculator app, press the button to insert „.”.
GETTING STARTED
BATTERY, SIM CARDS, AND MEMORY CARD INSTALLATION
- When the phone is off, use a screwdriver to twist off the screws and remove the back cover. Remove the battery if inserted.
- Insert SIM cards with pins down. Make sure, the cutouts on the cards are directed properly.
- Install microSD card (slide and lift the slot cover; place the card into the slot and close the cover). Make sure, the cutouts on the card are directed properly.
- Place the battery in the battery compartment (pay attention to correct polarity). Close the back cover. Tighten the mounting screws (make sure the back cover has been tightly closed).
Notes:
- Prior to battery/SIM/memory cards removal from the phone, disconnect the phone from the AC/DC adapter and turn it off (otherwise it can damage cards’ memory).
- Exercise caution when operating cards, like friction or bending, may damage them.
- The phone is not a toy, keep it away from children.
- Memory and SIM cards are very small objects. Keep them away from children!
- It is suggested to use memory cards of class 10 and higher. Other cards may not be compatible.
- If the memory card cannot be read, make sure it has been installed properly.
- The producer does not guarantee the compatibility of the device with every memory card.
- Note: Dual SIM will shorten the battery time compared to a single SIM.
- Make sure the battery is fully charged if it has been out of use for a long period.
INGRESS PROTECTION RATING
The device underwent tests in a controlled environment, which have proven the device is water and dust resistant under certain conditions – i.e. it meets IP68 classification requirements (Degree of protection provided by enclosures). The tests conducted under laboratory conditions indicated the device’s resistance during submersion to up to 1-meter depth for a period of up to 30 minutes. Do not use this device in conditions different from test conditions! Producer reserves the possibility for the results to vary in actual use.
Note: Despite this classification, your device is not impervious to water damage in any situation. Ensure the battery cover, lock screw, earphone, and USB rubber plugs are perfectly closed while using near water, or in a humid or dusty environment, to ensure the device remains waterproof and dustproof. Exposing this device in places where IP classification restrictions may be validated or subjecting the device to shock or falling down may result in loss of water and dust resistance. Do not expose the device to salt or ionized water.
Maintenance after removing from water
- After removing from water, do not uncover the phone body until it is completely wiped dry by towels or tissue papers.
- Open the cover facing downwards to prevent any water remaining in the cover slots from entering the phone’s body.
- Carefully dry away water drops from the phone’s speaker, earpiece, and microphone after the entire phone has been removed from the water, and then place to dry in the open air. Do not use electric hair dryers to dry the phone.
- NOTE: Water and dust protection rating is not permanent, and can decrease over time, as a result of everyday usage of the device. Despite the IP68 rating and strengthened casing, the device is not resistant to damages in certain situations. The warranty does not cover mechanical or liquid damages. The device will not be subject to warranty repair in the event of damage caused by exceeding the conditions of the IP classification requirements and those listed in the above user’s manual.
CHARGING
- Connect an AC/DC adapter to the device and power the main socket.
- When charging, the battery icon will be flashing until fully charged.
Note: Before charging, ensure that the voltage and frequency of the local mains supply match the rated voltage and power of the power adaptor.
Overheating
While charging, the temperature of the device and the charger may get
increased. This does not affect the device’s lifespan or performance and is in
the device’s normal range of operation.
However, if there is an excessive increase in temperature or overheating,
depending on the factor that caused it: the device’s performance may be
significantly reduced, the charging process may be stopped, the device may
turn off or display notification about switching off for cooling. Function
available only in selected models. Important: if the device displays a
notification about overheating, turn it off and do not turn it back on until
completely cooled down!
In case of overheating during charging:
- Disconnect the charger from the device.
- Close any running apps.
- Wait for the device to cool down, and then begin charging the device again.
If the part of the device where the USB port is placed overheats, check for damage to the connected USB cable. Replace the damaged USB cable with a new authorized cable.
The device may also overheat during operation when using several battery- consuming applications or functions. In case of overheating during usage:
- Close any running apps.
- Disconnect any connectivity (Bluetooth, Wi-Fi, data transfer, etc.).
- Lower the screen brightness settings.
- Wait for the device to cool down before attempting to use it again.
Safety precautions concerning operation environment
In order to maintain the battery’s longevity, and to avoid overheating, follow
basic precautions including provisions listed below:
- Do not use/store the device in very hot or cold environments nor expose it to direct sunlight (e.g. on a car’s dashboard when used as navigation).
- Do not place the device on surfaces that may cause overheat e.g. electric heating mat.
- Do not place near sources of heat e.g. radiators, microwave ovens, hot kitchen appliances, or high-pressure containers.
- DO NOT use a damaged charger or battery!
- Use only authorized chargers, batteries, and cables! Using unauthorized accessories may damage the device or battery. Connecting the charger with inadequate parameters may result in damage to the device and poses risk to the user.
OPERATION
TURN ON/OFF
To turn on the phone, press and hold button marked with a red receiver (end
call button). If the PIN code has been set beforehand, the device will be
prompt to input the digits.
To turn off the phone, press and hold button marked with a red receiver (end call button).
PHONE LOCK
To lock the phone, press and hold the “” button. Press the left function
button, then press the “” button to unlock the phone.
LANGUAGE SELECTION
To change language settings, press the B button OR go to Settings in the main
menu, open the Phone settings tab, and enter Language. Select desired and
confirm.
DIALING CALLS
Insert number using numerical buttons and press the button marked with a green
receiver (dial call button). Users can also dial the call by selecting a
number from the contact list or a call list.
ANSWERING/ENDING/REJECTING INCOMING CALLS
To answer an incoming call, press the button marked with a green receiver
(dial call button). To end/reject a call, press the button marked with a red
receiver (end call button).
Note: If the number is not restricted it will be displayed on the screen. And if the number is in the phone book, the contact name will be displayed too.
MESSAGES
To display messages, go to the appropriate tab in the main menu. To create a
new message, select “Write message”. For input method change when typing
message, press the “#” button
CONTACTS
Users can save names and phone numbers in SIM cards or phone memory. Color SIM
card symbol with a number, on the right of the entry in Contacts, symbolizes
on which card is the contact saved. Contacts with no symbol symbolize it is
saved on the phone.
ADDING NEW CONTACT
To add a new contact, select “Add new contact”. Then select desired to save
place: SIM1, SIM2, phone.
PHONEBOOK SETTINGS
- Speed dial: user can set up to 8 numbers for speed dial. Once a number has been set, press and hold the respective number (2-9) to dial a call.
- When on the main screen, to set voicemail number, press and hold the “1” button.
- Copy contacts: highlight the contact and select the copy contact option. If the phone or SIM card memory is full, the device will prompt about it on the screen.
- Delete all contacts: select the delete all contacts option and choose whether to delete contacts from SIM1/SIM2/phone.
CALL CENTER
Enter to display dialed, received, and missed calls. To display available
options, press the left function button (view number, call number, send SMS,
save to phonebook, add to the blacklist, delete).
POWER BANK FUNCTION
KM0459 model has a power bank function. The phone can serve as a portable
charging device. To charge an external device, connect a USB cable to the
phone and an external device and enable the function in the Tools tab.
INTERNET SERVICE
KM0460 model allows for connecting with the internet and has a preinstalled
Facebook app as well as support e-mail.
CLEANING
Use only a soft, slightly damp cloth to clean this product. Do not use any abrasives or any chemical detergents, as they may damage the phone.
TROUBLESHOOTING
If you experience difficulties when operating the mobile phone refer to the following table to solve the problem. If the problem persists, contact an authorized service point.
Problem | Cause | Solution |
---|---|---|
SIM card error | The SIM card is damaged | Contact your network service provider |
The SIM card is inserted incorrectly | Check the SIM card | |
The metal part of the SIM card is polluted | Clean the SIM card with a clean |
cloth
Poor quality of the received signal| Signals are obstructed. E.g., radio waves
cannot be effectively transmitted in a basement.| Move to a place where
signals can be effectively transmitted
The phone cannot be powered on| The battery is exhausted| Charge the battery
The battery may be installed improperly| Check if the battery has been
installed correctly
The battery cannot be charged| The charging voltage does not match the voltage
range indicated on the charger| Ensure the charging voltage matches the
voltage range indicated on the charger
Poor contact| Ensure the charger plug is in good contact
SPECIFICATION
| KM0459| KM0460
---|---|---
Main parameters| CPU: MTK6261D| CPU: MT6276A
RAM: 32 Mb| RAM: 64 MB
Internal memory: 32 Mb| Internal memory: 128 MB
External memory: max. 32 GB
Display| Size: 2,4” ǪVGA
Dimension: 240×320 px
Multimedia| Camera: 0,3 Mpx| Camera: 2,0 Mpx
FM Radio
Microphone
Speaker
–| Facebook
–| E-mail
Connectivity| Network: GPRS, WCDMA| Network: 3G, GPRS, WCDMA, WAP
–| WiFi: 802.11 b/g
Bluetooth: 2.1
I/O| Dual SIM
microSD card reader
micro USB
Earphone jack (3,5 mm)
Power supply| Power supply: 5 V / 1000 mA
Battery capacity: 2500 mAh
Power bank function| –
Ingress protection| IP68
IMPORTANT: The producer allows the possibility for minor variations in display brightness and color between individual devices. There may be visible light or dark spots on the display. Up to 5 defective pixels are acceptable to be present on the display of the device. Above mentioned cases concerning the device’s display are not covered under warranty nor statutory warranty rights.
LEARN MORE
For more information on this device visit:
www.krugermatz.com.
Read the owner’s manual carefully before using your device.
Visit the www.krugermatz.com website for more
products and accessories.
In case of any doubts or questions reach out to our Frequently Asked Questions
section.
Please note: illustrations and descriptions concerning operating systems are
for reference only, and may vary from actual software on your device!
Lechpol Electronics Sp. z o.o. Sp.k. hereby declares that mobile phone KM0459 / KM0460 is consistent with directive 2014/53/UE. Full text of the EU Declaration of Conformity is available at the following Internet address: www.lechpol.eu.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
It is forbidden to place equipment waste marked with the symbol of a crossed- out trash bin together with other waste. This equipment is subject to collection and recycling. The harmful substances it contains can cause environmental pollution and pose a threat to human health.
Made in China for LECHPOL ELECTRONICS Sp. z o.o. Sp.k.,ul. Garwolińska 1, 08-400 Miętne.
Notes
www.krugermatz.com
is a registered trademark