HAVIT Lightning HV2827W Uton Deck Light Instruction Manual
- June 4, 2024
- HAVIT LIGHTNING
Table of Contents
- Product Specifications
- Dimensions
- Single Colour Wiring Diagram
- RGB Wiring Diagram
- Important Safety Issues
- Steps for Installation: Single Colour Models
- Steps for Installation: RGB Models
- Must be installed by a licensed electrician
- Contact Details
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
HAVIT Lightning HV2827W Uton Deck Light Instruction Manual
Product Specifications
| Model No. | HV2827W | HV2827C | HV2827RGB | HV28271W | HV28271C | HV28271RGB |
|---|---|---|---|---|---|---|
| Name | Uton | |||||
| Material | Polycarbonate |
White
Colour
IP Rating| IP67
240V – Driver | 12v DC Fittings
12V DC
Input Voltage
Protection Class| Driver | Fitting(Low Voltage)| (Low Voltage)
Built in LED
1x 0.5w
Lamp Base| Built in LED
Lamp Wattage| 6x 0.5w
Colour Temp| 3000k| 5500k| RGB| 3000k| 5500k| RGB
25lm
Lumens| 6x 40lm| 6x 50lm| 6x 25lm| 40lm| 50lm
CRI| > 80 Parallel
Wiring
Dimmable| No 3 Years Replacement*
Warranty
Dimensions
Single Colour Wiring Diagram
RGB Wiring Diagram
Important Safety Issues
- This product must be installed by a qualified electrician according to AS/NZS 3000.
- Ensure all electrical mains are disconnected before any installation.
- Modification of this product will void any warranty.
- Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
- When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required, if not within this allowance warranty will be voided.
- All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting. (Warranty does not cover Tea Staining)
- All o-rings and seals must be in place correctly to maintain warranty
- This form may be updated at any time due to product improvements, please check online installation form for most current version.
Steps for Installation: Single Colour Models
- Make sure that the electrical circuit is free of voltage (master switch off )
- Make a hole where fitting is to be placed using dimensions provided on line drawings, making sure adequate drainage is allowed.
- Using an appropriate 12v DC LED Driver or if installing kit, use LED Driver supplied – DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V
- Connect the cable by connecting male plug from fitting to 4 metre extension cable from LED Driver.
- Insert fitting into hole
- Repeat steps 4 + 5 until all fittings are installed
- All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.
Steps for Installation: RGB Models
- Make sure that the electrical circuit is free of voltage (master switch off )
- Make a hole where fitting is to be placed using dimensions provided on line drawings, making sure adequate drainage is allowed.
- Using an appropriate 12v DC LED Driver or if installing kit, use LED Driver supplied – DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V
- Connect RGB Controller to LED Driver
- Connect the cable by connecting male plug from fitting to 4 metre extension cable from RGB Controller.
- Insert fitting into hole
- Repeat steps 5 + 6 until all fittings are installed
- All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.
Must be installed by a licensed electrician
Warranty Terms & Conditions
Additional Information
Contact Details
143 Beauchamp Road Tel: 02 9381 8300
Matraville NSW 2036 Fax: 02 9666 8881
Australia Email: sales@havit.com.au
Web: www.havit.com.au
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>