HAVIT Lightning HV1701T Outdoor Lightning Instruction Manual

HV1701T Outdoor Lightning
Instruction Manual

Product Specifications

Dimensions

Important Safety Issues:

• This product must be installed by a qualified electrician according to AS/NZS 3000.
• Ensure all electrical mains are disconnected before any installation.
• Do not exceed maximum wattage restrictions for globes: 240V GU10 = 35w / 12V MR16 = 20w
• Modification of this product will void any warranty.
• Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
• When installing low voltage fittings, Voltage to fitting must be within +or- 5% of the voltage required and cannot be installed more than 25m from LED Driver, if not within this allowance warranty will be voided.
• Aluminum and 304SS fittings must not be installed within 2km of any saltwater environments.
• When installing copper fittings, gloves must be worn to avoid any oils transferring to the fitting.
• All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on the fitting. (Warranty does not cover Tea Staining)
• All o-rings and seals must be in place correctly to maintain the warranty.
• These instructions may be updated at any time due to product improvements, Please visit the website for the most current installation instructions.

Sample Adequate Drainage Diagram

Steps for Installation:

1. Make sure that the electrical circuit is free of voltage (master switch off )
2. Make a hole where the fitting is to be placed using dimensions provided on line drawings, making sure adequate drainage is allowed.
3. Insert canister, and ensure that the top is level with the ground or floor. Failure to do so will void the warranty.
4. Use an appropriate 12v DC LED Driver – DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V
5. Connect the cable – If more than one fitting is installed, wiring must be done in parallel.
6. Strip back the cable on both fitting and cable run and twist the positive cable from fitting to positive on the cable run. Then connect neutral from fitting to neutral on the cable run.
7. Solder all joins using solder and either a heat gun or butane gas torch.
8. Cover connections using an adhesive-lined heat shrink or gel cap to make the connection watertight. Failure to do this will void the warranty.
9. Heat the heat shrink or crimp the gel cap making sure all connections are covered.
10. The Colour temperature is set to 3000K factory. To change, unscrew 4x allen screws on the face from the fitting, Remove the globe and select desired color temperature by moving the switch on side of the globe and reinserting the globe.
11. Reinsert the 4x allen screws and tighten making sure the seals are still in place and the screws are tight to avoid any water penetration.
12. Insert fitting into the canister. Apply silicon around the edge of the fitting to prevent any water from getting inside to electrical connections.
13. All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.

Steps for Changing Globe:

1. To change, unscrew 4x allen screws on the face of the fitting, Remove the globe by grabbing around the edge and pulling gently, and Re-insert the appropriate globe, making sure the new lamp does not exceed max wattage, see product label for information.
2. Reinsert the 4x allen screws and tighten making sure the seals are still in place and the screws are tight to avoid any water penetration.

Must be installed by a licensed electrician

Contact Details:
143 Beauchamp Road
Matraville NSW 2036
Australia
Tel: 02 9381 8300
Fax: 02 9666 8881
Email:
sales@havit.com.au
Web: www.havit.com.au

**Warranty Terms & Conditions***

https://havit.com.au/pages/warranty-terms-and-conditions

Additional Information

https://havit.com.au/collections/lighting/products/hv1701t-hv1706t-metro- square-316-stainless-steel-tri-colour-inground-lights
https://havit.com.au/collections/lighting/products/hv1801t-hv1806t-metro- round-316-stainless-steel-tri-colour-inground-lights

References

• Havit Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>