HAVIT Lightning HV3275T-BLK-12V Virsma Step Light Instruction Manual
- June 4, 2024
- HAVIT LIGHTNING
Table of Contents
Visma Step Light Installation Instructions
Product Specifications
Model No.| 1-1V3275T-ELK-12V|
FIV3275T-VVHT-12V
---|---|---
Name|
Visma
Material|
Aluminium
Colour|
Black
|
White
IP Rating|
IP5
Input Voltage|
12v DC
Lamp Base|
Buik in LE
Lamp Wattage|
1x 6w
Colour Temp|
TR1 Colour – 3000k, 4000k, 5500k
Lumens|
2001m, 2101m, 2201m
CR1|
> 80
Wiring|
Parallel
Dimmable|
No
Warranty|
2 Years Replacement*
Dimensions
Mounting Base Diagram
Important Safety Issues:
- This product must be installed by a qualified electrician according to AS/NZS 3000.
- Ensure all electrical mains are disconnected before any installation.
- Do not exceed maximum wattage restrictions for globes: 240V GU10 = 35w / 12V MR16 = 20w
- Modification of this product will void any warranty.
- Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
- When installing low voltage fittings, Voltage to fitting must be within +or- 5% of the voltage required and cannot be installed more than 25m from LED Driver, if not within this allowance warranty will be voided.
- Aluminum and 304SS fittings must not be installed within 2km of any saltwater environments.
- When installing copper fittings, gloves must be worn to avoid any oils transferring to the fitting.
- All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on the fitting. (Warranty does not cover Tea Staining)
- All o-rings and seals must be in place correctly to maintain the warranty.
- These instructions may be updated at any time due to product improvements, Please visit the website for the most current installation instructions.
Steps for Installation:
- Make sure that the electrical circuit is free of voltage (master switch off )
- Loosen Allen screws on side of the fitting and remove the face and set it aside.
- Install base plate to wall in the desired location
- Using an appropriate 12v DC LED Driver – DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V
- Connect the cable – If more than one fitting is installed, wiring must be done in parallel.
- Fitting is preset to 3000k, to change the slide switch to desired color temperature
- Reattach face to base plate making sure Allen screws are tight to avoid water penetration
- Apply silicon around the edge of the fitting to prevent any water from getting inside to electrical connections.
- All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.
Must be installed by a licensed electrician
Contact Details:
143 Beauchamp Road
Matraville NSW 2036
Australia
Tel: 02 9381 8300
Fax: 02 9666 8881
Email: sales@havit.com.au
Web: www.havit.com.au
**Warranty Terms & Conditions***
https://havit.com.au/pages/warranty-terms-and-conditions
Additional Information
https://havit.com.au/collections/all/products/hv3275t-wht-virsma-white- rectangle-led-step-lights| https://havit.com.au/collections/all/products /hv3275t-blk-virsma-black-rectangle-led-step-lights
Product Specifications
Model No.
| HV3275T-BLK-240V|
HV3275T-WHT-240V
---|---|---
Name|
Virsma
Material|
Aluminum
Colour
| Black|
White
IP Rating|
IP54
Input Voltage|
240v A
Lamp Base|
Built-in LED
Lamp Wattage|
1x 6w
Colour Temp|
TRI Colour – 3000k, 4000k, 5500k
Lumens|
2001m, 2101m, 2201
CRI|
80
Wiring|
Parallel
Dimmable|
No
Warranty|
2 Years Replacement*
Dimensions
Mounting Base Diagram![HAVIT Lightning HV3275T-BLK 12V Virsma Step Light
- Fig](https://manuals.plus/wp-content/uploads/2022/10/HAVIT-Lightning- HV3275T-BLK-12V-Virsma-Step-Light-Fig.png)
Important Safety Issues:
- This product must be installed by a qualified electrician according to AS/NZS 3000
- Ensure all electrical mains are disconnected before any installation.
- Modification of this product will void any warranty
- Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system
- When installing low voltage fittings, Voltage to fitting must be within +or- 5% of the voltage required, if not within this allowance warranty will be voided.
- Aluminum and 304SS fittings must not be installed within 2km of any saltwater environments.
- When installing copper fittings, gloves must be worn to avoid any oils transferring to the fitting.
- All 316 & 304 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on the fitting. (Warranty does not cover Tea Staining)
- All o-rings and seals must be in place correctly to maintain the warranty
- This form may be updated at any time due to product improvements, please check the online installation form for the most current version.
Steps for Installation:
- Make sure that the electrical circuit is free of voltage (master switch off )
- Loosen Allen screws on side of the fitting and remove the face and set it aside.
- Install base plate to the wall in the desired location
- Connect the cable – use wire with earth; connect the earth first, then live and neutral wire
- Fitting is preset to 3000k, to change the slide switch to desired color temperature.
- Reattach face to base plate making sure Allen screws are tight to avoid water penetration
- Apply silicon around the edge of the fitting to prevent any water from getting inside to electrical connections.
- All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.
Must be installed by a licensed electrician
Contact Details:
143 Beauchamp Road
Matraville NSW 2036
Australia
Tel: 02 9381 8300
Fax: 02 9666 8881
Email: sales@havit.com.au
Web: www.havit.com.au
**Warranty Terms & Conditions***
https://havit.com.au/pages/warranty-terms-and-conditions
Additional Information
https://havit.com.au/collections/all/products/hv3275t-wht-virsma-white- rectangle-led-step-lights| https://havit.com.au/collections/all/products /hv3275t-blk-virsma-black-rectangle-led-step-lights