HAVIT Lightning HV1616 Bollard Light Instruction Manual

: June 4, 2024
: HAVIT LIGHTNING

Table of Contents

Product Specifications
Dimensions
Important Safety Issues:
Mounting Base Dimensions
Steps for Installation:
Steps for Changing Globe:
Must be installed by a licensed electrician
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

HAVIT Lightning HV1616 Bollard Light Instruction Manual

HAVIT Lightning HV1616 Bollard Light Instruction
Manual

Product Specifications

HAVIT Lightning HV1616 Bollard Light Instruction Manual - Product
Specifications

Dimensions

HV1606
HV1616

HAVIT Lightning HV1616 Bollard Light Instruction Manual -
Dimensions

Important Safety Issues:

This product must be installed by a qualified electrician according to AS/NZS 3000.
Ensure all electrical mains are disconnected before any installation.
Modification of this product will void any warranty.
Habit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
All electrical connections must be watertight, If a watertight connection is not done, Warranty will be voided.
When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required and cannot be installed more than 25m from LED Driver, if not within this allowance warranty will be voided.
All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting. (Warranty does not cover Tea Staining).
When installing surface mounted bollards, base plate must be installed on concrete or concrete pad, Fitting should not be installed under ground level, all holes including cable entry must be silicone to prevent any water penetration into fitting, silicon must also be applied around fitting at ground level. Failure to do this will void warranty
All O-rings and seals must be in place correctly to maintain warranty.
These instructions may be updated at any time due to product improvements, Please visit website for most current installation instructions.

Mounting Base Dimensions

Steps for Installation:

Make sure that the electrical circuit is free of voltage (master switch off ).
Remove 4x allen screws from side of fitting and put aside
Install baseplate in desired location using appropriate screws for application. The screws supplied are mild steel which must be replaced with higher grade if there is any chance of them being affected by water. The location of baseplate must be installed on either concrete or concrete base and cannot be installed under ground level.
Locate IP rated junction box within fitting. Undo screws from junction box and remove cover.
Insert cable through cable gland on junction box. If your cable is not circular you must fix entry of your cable to maintain IP rating. Failure to do so will void warranty.
Using an appropriate 12V DC LED driver – DO NOT CONNECT FITTING DIRECTLY TO 240V
Connect live and neutral wires. If more than one fitting is installed, wiring must be done in parallel.
Reattach cover to IP rated junction box making sure screws are tight and seals are still in place.
Silicon all cable entry holes and fixing points on baseplate to avoid moisture penetration into fitting.
Place bollard onto base plate and reattach 4x allen screws set aside earlier
Colour temperature is set to 3000K. To change, remove cover from fitting by twisting anti clockwise. for HV1605 models, remove the 2x nuts and washers and put aside Remove globe by also twisting anti clockwise and select desired colour temperature by moving switch on side of globe and then reinsert globe.
Reattach cover by turning clockwise or for HV1605 Models, reattach the 2x nuts first, making sure the seals are still in place and cover is tight to avoid any water penetration.
All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.

Steps for Changing Globe:

Remove cover from fitting by twisting anti clockwise. for HV1605 models, remove the 2x nuts and washers and put aside Remove globe by also twisting anti clockwise.
Re-insert the appropriate globe by twisting clockwise into the lamp holder (Make sure not to exceed max wattage, see product label for correct info)
Reattach cover by turning clockwise or for HV1605 Models, reattach the 2x nuts first, making sure the seals are still in place and cover is tight to avoid any water penetration.