HAVIT Lightning HV1305T 9 In 1 Tivah Double Adjustable Exterior Spot Light Instruction Manual

: June 4, 2024
: HAVIT LIGHTNING

9in1 Tivah Double Adjustable Installation Instructions

Product Specifications

Model No.| FIVI 30ST| HV1315T I| HV1325T| I FiV1335T| I HI/134ST I| FIV1385T| I FIV1395T
---|---|---|---|---|---|---|---
Name| Tivah
Material| 316 Stainless Steel| Solid Copper| Aluminium| Aluminium| Aluminium| Aluminium| Solid Brass
Colour| Stainless Steel| Copper| Black| White| Silver| Titanium| Antique Brass
IP Rating| 1P65
Input Voltage| 240v AC
Lamp Base| GU10
Lamp Wattage| 2x 3w, 5w, 7w
Colour Temp| TRI Colour – 3000k, 4000k, 5500k
Lumens| 2x 240-560Im, 2x 255-5951m, 2x 270-6301m
CRI| > 80
Wiring| Parallel
Dimmable| No (with globes supplied)
Warranty| 2 Years Replacement*

Dimensions:

Important Safety Issues:

This product must be installed by a qualified electrician according to AS/NZS 3000.
Ensure all electrical mains are disconnected before any installation.
Do not exceed maximum wattage restrictions for globess: 240V GU10 = 35w / 12V MR16 = 20w
Modification of this product will void any warranty.
Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required, if not within this allowance warranty will be voided.
Aluminium and 304SS fittings must not be installed within 2km of any saltwater environments.
When installing copper fittings, gloves must be worn to avoid any oils transferring to fitting.
All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting. (Warranty does not covers Tea Staining)
All o-rings and seals must be in place correctly to maintain warranty.
These instructions may be updated at any time due to product improvements, Please visit website for most current installation instructions.

Steps for Installation:

Make sure that the electrical circuit is free of voltage (master switch off )
Loosen allen screws on side of base and separate mounting bracket from fitting.
Install the backing plate securely using appropriate screws for application, Seal all holes in the backing plate including cable entry and screw holes. Failure to do so will void warranty.
Connect the cable – use wire with earth; connect the earth first, then live and neutral wire
Affix the fiiting to the mounting bracket and tighten allen screws, making sure these are tight to avoid any water penetration.
Apply silicon seal around the whole base plate to avoid any water getting into electrical connections.
Colour temperature and wattage is preset to 3000k and 7w, to change remove covers from fitting by twisting anti-clockwise and set aside. Remove globes and select desired colour temperature and wattage by moving switches on side of globes and reinsert globes into lamp holders.
Reattach covers by turning clockwise making sure the seals are still in place and caps are tight to avoid any water penetration.
Adjust fitting to desired position making sure to stop rotating when fitting cannot rotate anymore If forced fitting will continue to rotate and cause internal
cables to become entangled causing fitting to short. If this is done, warranty will be voided.
All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.

Steps for Changing Globes:

Remove the covers by twisting anti-clockwise and set aside, remove globes by also twisting anti-clockwise.
Re-insert the appropriate globes by inserting the 2 circular pins into the lampholder and twisting clockwise. (Make sure not to exceed max wattage, see product label for correct info)
Reattach covers by turning clockwise making sure the seals are still in place and caps are tight to avoid any water penetration.

Tivah Double Adjustable 5w GU10 Installation Instructions

Product Specifications

Model No.| HV1307GUIOT| HVI317GUlOT| HVI327GU10T| HV1347GU10T| HV1387GU10T| HV1387GU10T| HV1397GU10T
---|---|---|---|---|---|---|---
Name| Tivah
Material| 316 Stainless Steel| Solid Copper| Aluminium| Aluminium| Aluminium| Aluminium| Solid Brass
Colour| Stainless Steel| Copper| Black| White| Silver| Titanium| Antique Brass
IP Rating| IP65
Input Voltage| 240v AC
Lamp Base| GU1O
Lamp Wattage| 2x 5w
Colour Temp| TRI Colour – 3000k, 4000k, 5500k
Lumens| 2x 2701m, 2x 2851m, 2x 3001m
CR1| > 80
Wiring| Parallel
Dimmable| No (with globes supplied)
Warranty| 2 Years Replacement*

Dimensions:

Important Safety Issues:

This product must be installed by a qualified electrician according to AS/NZS 3000.
Ensure all electrical mains are disconnected before any installation.
Do not exceed maximum wattage restrictions for globess: 240V GU10 = 35w / 12V MR16 = 20w
Modification of this product will void any warranty.
Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required, if not within this allowance warranty will be voided.
Aluminium and 304SS fittings must not be installed within 2km of any saltwater environments.
When installing copper fittings, gloves must be worn to avoid any oils transferring to fitting.
All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting. (Warranty does not covers Tea Staining)
All o-rings and seals must be in place correctly to maintain warranty.
These instructions may be updated at any time due to product improvements, Please visit website for most current installation instructions.

Steps for Installation:

Make sure that the electrical circuit is free of voltage (master switch off )
Loosen allen screws on side of base and seperate mounting bracket from fitting.
Install the backing plate securely using appropriate screws for application, Seal all holes in the backing plate including cable entry and screw holes. Failure to do so will void warranty.
Connect the cable – use wire with earth; connect the earth first, then live and neutral wire
Affix the fiiting to the mounting bracket and tighten allen screws, making sure these are tight to avoid any water penetration.
Apply silicon seal around the whole base plate to avoid any water getting into electrical connections.
Colour temperature and wattage is preset to 3000k and 7w, to change remove covers from fitting by twisting anti-clockwise and set aside. Remove globes and select desired color temperature and wattage by moving switches on side of globes and reinsert globes into lamp holders.
Reattach covers by turning clockwise making sure the seals are still in place and caps are tight to avoid any water penetration.
Adjust fitting to desired position making sure to stop rotating when fitting cannot rotate anymore If forced fitting will continue to rotate and cause internal
cables to become entangled causing fitting to short. If this is done, warranty will be voided.
All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.

Steps for Changing Globes:

Remove the covers by twisting anti-clockwise and set aside, remove globes by also twisting anti-clockwise.
Re-insert the appropriate globes by inserting the 2 circular pins into the lampholder and twisting clockwise. (Make sure not to exceed max wattage, see product label for correct info)
Reattach covers by turning clockwise making sure the seals are still in place and caps are tight to avoid any water penetration.

Tivah Double Adjustable 5w MR16 Installation Instructions

Product Specifications

Model No.| HV1307MR16T| HV1317MR16T| HV1327MR16T| HV1337MR16T| HV1347MR16T| HV1387MR16T| HV1397MR16T
---|---|---|---|---|---|---|---
Name| Tivah
Material| 316 Stainless Steel| Solid Copper| Aluminium| Aluminium| Aluminium| Aluminium| Solid Brass
Colour| Stainless Steel| Copper| Black| White| Silver| Titanium| Antique Brass
IP Rating| IP65
Input Voltage| 12v DC
Lamp Base| MR16
Lamp Wattage| 2x 5w
Colour Temp| TRI Colour – 3000k, 4000k, 5500k
Lumens| 2x 2701m, 2x 2851m, 2x 3001m
CR1| > 80
Wiring| Parallel
Dimmable| No (with globes supplied)
Warranty| 2 Years Replacement*

Dimensions:

Important Safety Issues:

This product must be installed by a qualified electrician according to AS/NZS 3000.
Ensure all electrical mains are disconnected before any installation.
Do not exceed maximum wattage restrictions for globess: 240V GU10 = 35w / 12V MR16 = 20w
Modification of this product will void any warranty.
Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required, if not within this allowance warranty will be voided.
Aluminium and 304SS fittings must not be installed within 2km of any saltwater environments.
When installing copper fittings, gloves must be worn to avoid any oils transferring to fitting.
All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting. (Warranty does not covers Tea Staining)
All o-rings and seals must be in place correctly to maintain warranty.
These instructions may be updated at any time due to product improvements, Please visit website for most current installation instructions.

Steps for Installation:

Make sure that the electrical circuit is free of voltage (master switch off )
Loosen allen screws on side of base and seperate mounting bracket from fitting.
Install the backing plate securely using appropriate screws for application, Seal all holes in the backing plate including cable entry and screw holes. Failure to do so will void warranty.
Connect the cable – use wire with earth; connect the earth first, then live and neutral wire
Affix the fitting to the mounting bracket and tighten allen screws, making sure these are tight to avoid any water penetration.
Apply silicon seal around the whole base plate to avoid any water getting into electrical connections.
Colour temperature and wattage is preset to 3000k and 7w, to change remove covers from fitting by twisting anti-clockwise and set aside. Remove globes and select desired color temperature and wattage by moving switches on side of globes and reinsert globes into lamp holders.
Reattach covers by turning clockwise making sure the seals are still in place and caps are tight to avoid any water penetration.
Adjust fitting to desired position making sure to stop rotating when fitting cannot rotate anymore, If forced fitting will continue to rotate and cause internal
cables to become entangled causing fitting to short. If this is done, warranty will be voided.
All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.

Steps for Changing Globes:

Remove the covers by twisting anti-clockwise and set aside, remove globes by also twisting anti-clockwise.
Re-insert the appropriate globes by inserting the 2 circular pins into the lampholder and twisting clockwise. (Make sure not to exceed max wattage, see product label for correct info)
Reattach covers by turning clockwise making sure the seals are still in place and caps are tight to avoid any water penetration.

Must be installed by a licensed electrician

Contact Details:
143 Beauchamp Road Matraville NSW 2036 Australia
Tel: 02 9381 8300
Fax: 02 9666 8881
Email: sales@havit.com.au
Web: www.havit.com.au