LINDY 38139 V2 70m Cat.6 HDMI 10.2G and IR HDBaseT Extender with PoC User Manual

LINDY 38139 V2 70m Cat.6 HDMI 10.2G and IR HDBaseT Extender with PoC

IMPORTANT
Only use a direct Cat.5e/6/7 cable connection between the HDBaseT ports. Do not connect these ports to Network or Ethernet equipment or any active components

Safety Instructions

WARNING

Please read the following safety information carefully and always keep this document with the product. Failure to follow these precautions can result in serious injuries or death from electric shock, fire, or damage to the product. Touching the internal components or a damaged cable may cause electric shock, which may result in death. This device is a switching type power supply and can work with supply voltages in the range 100 – 240 VAC For worldwide usability four different AC adapters are enclosed: Euro type, UK type, US/Japan type, and Australia/New Zealand type. Use the appropriate AC adapter as shown in the picture and ensure it is firmly secured in place and does not detach by pulling before installing it into a power socket. To reduce risk of fire, electric shocks, or damage:

• Do not open the product or its power supply. There are no user-serviceable parts inside.
• Only qualified servicing personnel may carry out any repairs or maintenance.
• Never use damaged cables.
• Do not expose the product to water or places of moisture.
• Do not use this product outdoors it is intended for indoor use only.
• Do not place the product near direct heat sources. Always place it in a well-ventilated place.
• Do not place heavy items on the product or the cables.
• Please ensure any adapters are firmly secured and locked in place before inserting into a wall socket

Instructions for Use of Power Supply

• To connect the adapter
  Slide the desired plug adapter into the power supply and rotate clockwise until it locks into place.

• To remove the adapter
  Press the push button latch. While pressed, rotate the adapter anticlockwise.

Introduction

Thank you for purchasing the 70m Cat.6 HDMI 10.2G & IR HDBaseT Extender with PoC. This product has been designed to provide trouble-free, reliable operation. It benefits from both a LINDY 2-year warranty and free lifetime technical support. To ensure correct use, please read this manual carefully and retain it for future reference.
The 70m Cat.6 HDMI & IR HDBaseT Extender with PoC is an end-to-end solution for extending HDMI signals over long distances via Cat.6 network cable.HDBaseT is a globally recognized standard for high-quality distribution of AV content and other technologies, including power and control, over longer distances via low-cost Cat.6 or above cable. Supporting resolutions up to 4K Ultra HD, video can be viewed in stunning clarity. This provides a reliable solution for creating eye-catching digital signage in retail, immersive displays at events, or engaging setups in larger conference rooms or lectures halls. HDBaseT™ and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.
Please Note: The quoted lengths and resolutions are possible with a direct connection between Transmitter and Receiver using good quality Cat.6 solid core cable. Using a different cable type, or introducing wall plates, couplers, or patch panels may result in a reduction of possible distances.

Package Contents

• HDMI Transmitter
• HDMI Receiver
• IR Receiver, 1.5m
• IR Emitter, 1.5m
• 4 x Mounting Ears
• 24VDC 1A Multi-country Power Supply (UK, EU, US & AUS), Screw Type DC Jack: 5.5/2.1mm
• Lindy Manual

Features

• Supports resolutions up to 3840×2160@30Hz 4:4:4 8bit
• Audio Pass-through of all HDMI audio formats.
• Bi-directional PoC (Power over Cable) support, requiring a power supply connection from only one side of the installation.
• Bi-directional IR Control (20-60KHz) of equipment via the extender
• RS-232 & CEC Pass-through
• Screw Type DC Jack for a secure power connection

Specification

• HDMI 1.4, 10.2Gbps Compliant

• HDCP Pass-through
  The following distance and resolution combinations are possible when using high quality Cat.6 U/UTP or F/UTP cable:
  70m :

• 1920×1080@60Hz 4:4:4 8bit

• 3D@1920×1080
  40m :

• 3840×2160@30Hz 4:4:4 8bit

• 1920×1080@60Hz 4:4:4 8bit

• 3D@1920×1080

Transmitter Ports
Input:

• HDMI Type A (Female)

• IR (Female)
  Output:

• RJ-45 (Female)

• IR (Female)
  Receiver Ports:
  Input :

• RJ-45 (Female)

• IR (Female)
  Output:

• HDMI Type A (Female)

• IR (Female)

• ESD Protection: Human Body Model ± 8kV (air-gap discharge), ± 4kV (contact discharge)

• Operating Temperature: 0°C – 40°C (32°F – 104°F)

• Storage Temperature: -20°C – 60°C (-4°F – 140°F)

• Relative Humidity: 20 – 90% RH (Non-condensing)

• Metal Housing

• Colour: Black

• Power Requirements: AC100-240V 50/60Hz

• Power Consumption: 20W Maximum

Installation and Operation

Transmitter Front and Rear

1. Power LED: Indicates Power.
2. 24V DC: Connect the 24VDC 1A PSU to an AC wall outlet and securely connector to the transmitter or receiver. This is only required at one side of the installation.
3. HDBaseT Out: HDBaseT output port. Connect a compatible HDBaseT receiver using a single Cat.6 or above cable for all data signals. Please do not connect to a network port.
4. HDMI In: Connect to an HDMI source device.
5. IR In: Connect the supplied IR Receiver cable for IR signal reception. Ensure the remote being used is within the direct line-of-sight of the IR Extender.
6. IR Out: Connect the supplied IR Transmitter Cable for IR signal transmission. Place the IR Transmitter in direct line-of-sight of the equipment to be controlled.
7. RS-232: Connect to a PC, Serial Controller or Serial device via a phoenix block 3-way connection for the pass-through transmission of RS-232 commands.
8. Link Indicator LED:
9. Illuminated Green: Link is Okay
10. Not Illuminated: No Link
11. Data Signal Indicator LED:
12. Illuminated Orange: Signal is Okay
13. Not Illuminated: No HDMI Signal

Receiver Front and Rear

1. Power LED: Indicates Power.
2. 24V DC: Connect the 24VDC 1A PSU to an AC wall outlet and securely connector to the transmitter or receiver. This is only required at one side of the installation.
3. HDBaseT In: HDBaseT Input Port. Connect a compatible HDBaseT transmitter using a single Cat.6 or above cable for all data signals. Please do not connect to a network port.
4. HDMI Out: Connect to an HDMI display.
5. IR In: Connect the supplied IR Receiver cable for IR signal reception. Ensure the remote being used is within the direct line-of-sight of the IR Extender.
6. IR Out: Connect the supplied IR Transmitter Cable for IR signal transmission. Place the IR Transmitter in direct line-of-sight of the equipment to be controlled.
7. RS-232: Connect to a PC, Serial Controller or Serial device via phoenix block 3-way connection for the pass-through transmission of RS-232 commands.
8. Link Indicator LED:
9. Illuminated Green: Link is Okay
10. Not Illuminated: No Link
11. Data Signal Indicator LED:
12. Illuminated Orange: Signal is Okay
13. Not Illuminated: No HDMI Signal

Important! Before starting the installation, please ensure that all devices are powered off.

User Manual

1. Connect an HDMI source device to the Transmitter unit using HDMI cable.
2. Connect one end of the Cat.6/7 cable to the HDBaseT Out port on the Transmitter and the other end to the HDBaseT In port of the Receiver. U/UTP or F/UTP solid core installation cables are recommended. For cable lengths please see the Specifications of this manual.
3. Use another HDMI cable to connect an HDMI display device to the HDMI output port on the Receiver unit.
4. Plug the DC power supply into the Transmitter or Receiver and switch on.
5. Power on the source device and display to complete the installation. In addition to the installation steps outlined above this HDMI 10.2G Extender can also provide the following additional/optional functionality:

• RS-232 Serial
  The Transmitter and Receiver both feature a phoenix block serial connection for the extension of control signals.

• Infrared Control
  The Transmitter and Receiver units both feature an IR In and Out port, with two pairs of IR extension cables provided. The extension cables allow an IR remote control to be used from the Transmitter to the Receiver or vice versa.

IR Receiver

Troubleshooting

There is no display on the screen.
It has been found that there are significant differences in the cable lengths/types and even input ports which can be used on different brands of display using HDMI 18G 4K@60Hz resolutions. If problems are experienced, please apply the following steps:3

• Try a different input port on the display.
• Reduce the cable length on the Input and Output to 1m.
• Try a different type of 1m HDMI Cable.
• Check that the DC plug and jack used by the external power supply is firmly connected and that the power LED is illuminated on both the Transmitter and Receiver.
• Check that the Cat.6/7 cable is plugged in correctly and that the Connection LED on the left side of both the HDBaseT In and Out ports are illuminated.
• Check that the HDMI Indicator LED on the right side of the HDBaseT In and Out ports are illuminated, if not please power cycle the source and display.
• For several HDMI devices it may be helpful to unplug and re-connect their HDMI connection to re-initiate the HDMI handshake and recognition.
• Power off all the devices, then power on in this order: first, the extender, then the display and finally the source.
• Reduce the length of Cat.6/7 or HDMI cable used or use a higher quality cable.

Lindy regularly checks and tests our product range to ensure maximum compatibility and performance. For the most up to date version of this manual, please refer to your local Lindy website, search for the relevant part number and find the manual under Downloads.

No. 38139 V2
lindy.com
© LINDY Group – FIFTH EDITION (March 2021)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>