CHUANGO WS-105 Mini Indoor Strobe Siren User Manual
- June 6, 2024
- CHUANGO
Table of Contents
Mini Strobe Siren
WS-105
Operation Manual
Features
- Compact size with plug-in design
- 100% wireless configuration, D.I.Y. Installation
- Built-in 1,000,000 RF codes combination maintains high reliability
- E, PROM information protection, power failure won’t cause damage to data
- Simplified accessory expansion by automatic connecting
- Work with all kinds of our wireless accessories
- Mute operation for night, not disturbing neighborhood
- Built-in 3.7V /600mAh lithium battery enables 8-hour standby
Introduction
The wireless siren is powered by AC 100V-240V needs no wiring. According to different requirements, users can install more wireless sirens indoors in different places to deter illegal intruders.
Multiple wireless sirens in different places can be wirelessly connected with
the control panel to build a system. When the control panel receives alarm
signals from detectors,
wireless sirens will hoot and the strobe lights will flash.
The wireless siren can also be used as a control panel independently.
According to different requirements, users can choose the wireless accessories
in the same frequency as
the wireless siren, to connect them with the siren, which can build a
standalone on-site alarm system.
product overview
Power On/ Off
Power On
The siren is powered off in the default setting. Plug the siren into the AC
power socket, and then press the power switch button. The siren is powered on
after a long beep.
Power Off
Press connect button once under working status. Then press the connect button
for 6 seconds until a long beep is heard. The siren is powered off.
Siren and Strobe Light Indication
When armed, the siren beeps once, the strobe light will be on after one flash.
When disarmed, the siren beeps twice, the strobe light goes out after two
flashes.
When armed or disarmed in mute, the siren does not beep and the strobe light
does not flash.
Work as Wireless Siren
When it works as a wireless siren, the siren should be connected with a wireless control panel in advance. When the control panel is alarming, the siren hoots, and the strobe light flashes to deter illegal intruders.
Connect to Control Panel
Firstly, press the connect button (0.5 seconds), the wireless siren beeps
once, 3 seconds later, it gives out another beep, and the strobe light
flashes, now the siren goes into
connecting status. Secondly, press the [SOS] or [Arm] button on the panel, the
wireless siren, and control panel are connected successfully after one beep.
Press connect button again to exit connecting status after two beeps.
Notes: Please don’t trigger any accessory when connecting with the control panel.
Work as Standalone Alarm
The siren can build up a standalone alarm system by adding wireless
accessories.
When the siren is armed, if any sensor is triggered, the siren will hoot and
the strobe light will flash to deter illegal intruders.
Connect Wireless Accessories
Firstly, press the connect button (0.5 seconds), the wireless siren beeps
once, 3 seconds later, it gives out another beep, and the strobe light
flashes, now the siren goes into
connecting status. Secondly, press the wireless accessory once (Such as
pressing any button on the remote control or separate wireless door sensor
transmitter and the magnet),
and it will be connected after one beep. Repeat the above operation to connect
other accessories.
Note! The siren supports up to 40 wireless accessories.
Testing:
Press the [Arm] button on the remote control, if the wireless siren flashes
once, it means, the connection of the remote control is successful. Then
trigger the sensor, the siren will hoot.
If not, the connection fails, please reconnect.
Clear All Accessories or Panels
If you lose the wireless accessories, especially the wireless remote control,
all accessories should be cleared so that other people won’t be able to carry
out illegal activities with
the lost accessories.
Press down the connect button for 6 seconds until one beep is heard, at the same time, the LED indicator flashes twice, all connected accessories and panels will be cleared. To use the siren, please reconnect the accessories or panels.
Entry and Exit Delay
When the wireless accessories are set in Independent Delay Zone, entry and exit delay can be applied to the siren. After setup, press the [Arm] button once on the remote control, the siren beeps once every 5 seconds until it goes into Arm status. Press the [Arm] button twice, the siren goes into Arm status immediately. Once the wireless accessories are triggered, the siren will hoot after the delayed time (Siren ringing time is 3 minutes).
The setup method is as below:
Press connect button twice, delay 15 seconds.
Press connect button three times, delay 30 seconds.
Press connect button four times, no delay.
Default setting: no delay.
The above delay setting is effective only for the accessories in Independent
Delay Zone, not effective for those accessories in Home Mode Zone@ and Normal
Zone.
Zone Setting for Wireless Accessories
Home Mode Zone: Press the [Stay] button on the remote control, the siren
beeps once. Then all the detectors are armed except those in “Home Mode Zone”
are disarmed,
which enables users to move freely at home.
24-H Zone: In any condition, the system will alarm immediately once the 24-H
zone detector is triggered.
If the zone setting is changed, the accessories need to be reconnected with
the control panel.
Switch On/Off Night Lamp
When the siren works as a standalone alarm, it can also be used as a LED night
lamp.
Press the [Stay] button twice on the remote control, the siren will enter Home
Mode and the strobe light will be switched on silently as a night lamp. Press
the [Disarm] button, the siren will be disarmed and the strobe light will be
switched off.
Specifications
Power Supply
AC 100V-240V
Volume: 90dB
Backup Battery
3.7V I 600mAh Lithium Battery, 2.22Wh
Static Current
< 13mA
Alarm Current
< lOOmA
Radio Frequency
315MHz 0r 433.92MHz(±75KHz)
Housing Material
ABS plastic
Operation Condition
Temperature: 0C-+ 55C°
Relative Humidity: < 80% (non-condensing)
Dimensions
90 x 90 x 42.2mm (not include plug part)
Ver: WS-105-EN-V1.1
© 2015 Chuango. All Rights Reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>