CHUANGO WS-105 Multilingual Mini Strobe Siren User Manual

June 4, 2024
CHUANGO

CHUANGO LOGO Multilingual Mini Strobe Siren
User Manual
CHUANGO WS-105 Multilingual Mini Strobe Siren - Featured
Image
WS-105
Mini Strobe Siren

Features

  1. Compact size with plug-in design
  2. 100% wireless configuration, D.I.Y. Installation
  3. Built-in 1,000,000 RF codes combination maintains high reliability
  4. E ² PROM information protection, power failure won’t cause damage to data
  5. Easy to pair automatically with accessories
  6. Work with all kinds of our wireless accessories
  7. Mute operation for the night, not disturbing the neighborhood
  8. Built-in 3.7V 600mAh lithium battery enables 8-hour standby

Introduction

The wireless siren is powered by AC 100V ~ 240V, without the need for wiring. According to different requirements, users can install more wireless sirens indoors in different places to deter illegal intruders.
Multiple wireless sirens in different places can be wirelessly connected with the control panel to build a system. When the control panel receives alarm signals from detectors, wireless sirens will hoot and the strobe lights will flash.
The wireless siren can also be used as a control panel independently.
According to different requirements, users can build up a standalone on-site alarm system by connecting new homo-frequency accessories with this siren.

Product Overview

  1. Power Switch/Connect Button
  2. Strobe Light
  3. Siren

Power On/Off

Power On
The siren is powered off in the default setting. Plug the siren into the AC power socket, and then press the power switch button. The siren is powered on after a long beep.
Power Off
Press connect button once under working status. Then press the connect button for 6 seconds until a long beep is heard. The siren is powered off.

Strobe Light Indication

When armed, the strobe light will be on after one flash.
When disarmed, the strobe light goes out after two flashes.

Work as Wireless Siren

When it works as a wireless siren, the siren should be connected with a wireless control panel in advance. When the control panel is alarming, the siren hoots, and the strobe light flashes to deter illegal intruders.

Connect to Control Panel
Firstly, press the connect button (0.5 seconds), and the wireless siren beeps once. 3 seconds later, it gives out another beep, and the strobe light flashes, then the siren goes into connecting status.
Secondly, press the [SOS] or [Arm] button on the panel, the wireless siren and control panel are connected successfully after one beep.
Press connect button again to exit connecting status after one beep.
Notes : Please don’t trigger any accessory when connecting with the control panel.

Testing:
Press the [Arm] button on the remote control, if the built-in siren of the control panel and wireless siren beep once, the connection is successful. If not, the connection fails, please reconnect them.

Work as a Standalone Alarm

The siren can build up a standalone alarm system by adding wireless accessories.
When the siren is armed, if any sensor is triggered, the siren will hoot and a strobe light will flash to deter illegal intruders.

Connect Wireless Accessories
Firstly, press the connect button (0.5 seconds), and the wireless siren beeps once. 3 seconds later, it gives out another beep, and the strobe light flashes, then the siren goes into connecting status.
Secondly, trigger the wireless accessory once (such as pressing any button on the remote control / separating the transmitter and magnet of the door contact/pressing the test button of the motion detector), and it will be connected after one beep. Repeat the above operation to connect other accessories.
Note : The siren supports up to 40 wireless accessories.

Testing:
Press the [Arm] button on the remote control, if the wireless siren flashes once, it means the connection of the remote control is successful. Then trigger the sensor, and the siren will hoot. If not, the connection fails, please reconnect.
Delete All Accessories or Panels
If you lose the wireless accessories, especially the wireless remote controls, it is recommended to delete all the accessories and then re-connect for safety.
Press down the connect button for 6 seconds until one beep is heard, at the same time, the LED indicator flashes twice, it means all connected accessories and panels are deleted.

Entry and Exit Delay

Entry and exit delay times can be set if you do not want to take the remote control.
After setup, if you arm the system, the siren beeps once every 5 seconds until it goes to an arm state. If the detectors (except those in the 24-H zone) are triggered, the siren will sound the alarm after the delay time. (Siren ringing time is 3 minutes). The setup method is as below:
Press Connect Button twice, and delay 30 seconds.
Press Connect Button three times, and delay 60 seconds.
Press Connect Button four times, with no delay.
Default setting: No delay.
Note : Press the [Arm] button on the remote control twice, and the system switches to the armed state immediately.

Switch On/Off Night Lamp

When the siren works as a standalone alarm, it can also be used as a LED night lamp.
Press the [Stay] button on the remote control, its LED indicator blinks once, and then press the [Stay] button again within 3 seconds, the siren switches to home mode silently and the night lamp is on. Press the [Disarm] button, and the siren will be disarmed and the strobe light will be switched off.

Specifications

Power Supply: AC 100 V-240 V, 50/60 Hz
Volume: 90 dB
Backup Battery: 3.7 V 600 mAh lithium battery, 2.22 Wh
Static Current: <13 mA
Alarm Current: <100 mA
Radio Frequency: 433 MHz
Housing Material: PC+ABS plastic
Operation Condition:
Temperature: 0 °C ~ +55 °C
Relative Humidity: < 80% (non-condensing)
Dimensions: 90 x 90 x 42.2 mm (Plug part excluded)

Printed in China
Ver: WS-105-UM-ML-V1.0

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals