CHUANGO WS-105 Mini Strobe Siren User Manual
- June 5, 2024
- CHUANGO
Table of Contents
- CHUANGO WS-105 Mini Strobe Siren
- Introduction
- Product Overview
- Power on/ off
- Work as Wireless Siren
- Work as Standalone Alarm
- Entry and Exit Delay
- Zone Setting for Wireless Accessories
- Switch on/off Night Lamp
- Specifications
- CE Declaration of Conformity
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
CHUANGO WS-105 Mini Strobe Siren
Introduction
The wireless siren is powered by AC 100V~240V According to different
requirements, users can install more wireless sirens indoor in different
places to deter the illegal intruders.
Multiple wireless sirens in different places can be wirelessly connected with
the control panel to build a system. When the control panel receives alarm
signals from detectors, wireless sirens will hoot and the strobe lights will
flash.
The wireless siren can also be used as a control panel independently.
According to different requirements, users can choose the wireless accessories
in same frequency with the wireless siren, to connect them with the siren,
which can build a standalone on-site alarm system.
Product Overview
Power on/ off
Power on
The siren is powered off in default setting. Plug the siren into AC power
socket, and then press the power switch button. The siren is powered on after
a long beep.
Power off
Press connect button once under working status. Then press the connect button
for 6 seconds until a long beep is heard. The siren is powered off.
Siren and Strobe Light Indication
When armed, the strobe light will be on after one flash. When disarmed, the strobe light goes out after two flashes. When armed or disarmed in mute, the siren does not beep and the strobe light does not flash.
Work as Wireless Siren
When it works as a wireless siren, the siren should be connected with wireless control panel in advance. When the control panel is alarming, the siren hoots and the strobe light flashes to deter illegal intruders.
Connect to Control Panel
Firstly, press the connect button (0.5 seconds), the wireless siren beeps
once, 3 seconds later, it gives out another beep and the strobe light flashes,
now the siren goes into connecting status. Secondly, press [SOS] or [Arm]
button on the panel, the wireless siren and control panel are connected
successfully after one beep. Press connect button again to exit connecting
status after one beep.
Notes: Please don’t trigger any accessory when connecting with the
control panel.
Work as Standalone Alarm
The siren can build up a standalone alarm system by adding wireless
accessories.
If there is any sensor be triggered in armed mode,the siren will hoot and the
strobe light will flash to deter illegal intruder.
Connect Wireless Accessories
Firstly, press the connect button (0.5 seconds), the wireless siren beeps
once, 3 seconds later, it gives out another beep and the strobe light flashes,
now the siren goes into connecting status. Secondly, trigger the wireless
accessory once (Such as press any button on remote control or separate
wireless door sensor transmitter and the magnet or press the test button on
the backside of PIR sensor), and it will be connected after one beep. Repeat
the above operation to connect other accessories.
Note! The siren supports up to 40 wireless accessories.
Testing:
Press the [Arm] button on the remote control, if the wireless siren flashes
once, it means, the connection of remote control is successful. Then trigger
the sensor, siren will hoot. If not, the connection fails, please reconnect.
Clear All Accessories or Panels
If accessories are losing, especially the wireless remote control, it is
suggestive to deleting and reconnecting all accessories for security.
Press down the connect button for 6 seconds until one beep is heard, at the
same time, the LED indicator flashes twice, all connected accessories and
panels will be cleared. To use the siren, please reconnect the accessories or
panels.
Entry and Exit Delay
When the wireless accessories are set in Independent Delay ZoneCD, entry and exit delay can be applied to the siren. After setup, press the [Arm] button once on the remote control, the siren beeps once every 5 seconds until it goes into Arm status. Press the [Arm] button twice, the siren goes into Arm status immediately. Once the wireless accessories are triggered, the siren will hoot after delayed time (Siren ringing time is 3 minutes).
The setup method is as below:
Press connect button twice, delay 15 seconds. Press connect button three
times, delay 30 seconds. Press connect button four times, no delay.
Default setting: no delay.
The above delay setting is effective only for the accessories in Independent
Delay Zone, not effective for those accessories in Home Mode Zone@ and Normal
Zone®.
Zone Setting for Wireless Accessories
Home Mode Zone: Press [Stay] button on the remote control, then all the detectors are armed except those in “Home Mode Zone” are disarmed, which enables users to move freely at home.
24-H Zone: In any condition, the system will alarm immediately once the 24-H zone detector is triggered.
Change the zone: Open the shell of accessories, there is a small area for zone setting in accessories. If the zone setting is changed, the accessories need to be reconnected with the control panel.
Switch on/off Night Lamp
When the siren working as a standalone alarm, it can also be used as a LED
night lamp.
Press the [Stay] button twice on the remote control, the siren will enter Home
Mode and the strobe light will be switched on silently as a night lamp. Press
[Disarm] button, the siren will be disarmed and the strobe light will be
switched off.
Specifications
- Power Supply: AC 100V~240V
- Volume: 90dB
- Backup Battery: 3.7V/ 600mAh Lithium Battery, 2.22Wh
- Static Current: < 13mA
- Alarm Current: < lOOmA
- Radio Frequency: 315MHz or 433.92MHz(± 75KHz)
*Only 433.92MHz is available for Europe - Housing Material: ABS plastic
- Operation Condition:
- Temperature: 0° C ~ S0° C
- Relative Humidity: < 80% (non-condensing)
- Dimensions: 90 x 90 x 42.2mm (not include plug part)
CE Declaration of Conformity
Hereby, Chuang a Alo T GmbH declares that the Mini Strobe Siren WS-105 is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address:
https://www.chuango.com/english/complianee_WS-105
INFORMATION FOR THE USERS
At the end of its life, the device has to be separated from the other
waste. Consign the device and all its components together to a center of
electronical and electrotechnical waste recycling center, designated by your
local authorities.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>