CHUANGO WS-280 Wireless Outdoor Strobe Siren User Manual
- June 13, 2024
- CHUANGO
Table of Contents
CHUANGO WS-280 Wireless Outdoor Strobe Siren
Introduction
Wireless outdoor strobe siren is to deter the intruders through hooting once it receives wireless signal from connected control panel or sensors. More wireless strobe sirens could be connected to the same control panel to strengthen the deterrent effect. When the siren is connected to control panel as an accessory, it will hoot and its LED lights will flash once the system is triggered. When the siren is connected to sensors like remote control, door/window contact, and PIR motion detector, etc. as an standalone alarm control panel, it will hoot and its LED lights flash once any sensor is triggered.
Product Overview
Front View
Status LED Indication
| Status | LED |
|---|---|
| Arm/Home Mode | Flash once every 5 seconds |
| Disarm | No light indication |
| No disarm operation after alarm | Flash once every 2 seconds for 2 hours |
Rear View
PCB Layout
Jumper Setup I
- Please setup alarming volume and alarming duration time on the PCB board accordingly.
Alarming Volume Setup
Note: When the siren is connected to control panel, it will hoot at the pre-set volume even if the control panel is set to mute alarm. This is to alert the neighbors and avoid the intrusion. When the control panel is set to mute disarm/arm, the siren will be disarmed/ armed mutely. When the siren is set to mute mode, there are still tones for arming and disarming.
Alarming Duration Setup
Work as Wireless Siren
When it works as a wireless siren, it should be connected with wireless control panel in advance. When the control panel is alarming, it hoots and the strobe light flashes to deter illegal intruders.
Connect to Control Panel
Press the Learn button for 0.5 second, siren beeps once and enter connection
status. Press on the panel (or press Arm on App if the panel does not have a
button), the wireless siren and control panel are connected successfully after
one beep is heard from siren.
Note: Once the siren is in connection status, please press Learn button again to exit. One beep will be heard from siren. When connecting to control panel, please don’t trigger any other sensors to avoid interference.
Disconnection
Hold the Learn button till 2 beeps are heard to disconnect the siren and
control panel.
Work as Standalone Alarm Panel
When it works as a standalone alarm panel, it should be connected with wireless sensors or wired sensors in advance, when the intrusion is detected, it hoots and the strobe light flashed to deter illegal intruders.
Wired Terminals
The siren has terminals for power supply and wired sensors. Just connect the
power line or wired sensors to the hardwired terminals. Please make sure the
positive and negative are disinguished.
- Power: DC 12V Input
- Zone(normal zone mode): Once the sensor in normal zone mode is triggered, the system will alarm immediately.
- 24-Zone(24-H zone mode): Once the sensor in 24-H zone mode is triggered, the system will alarm immediately, no matter what circumstances the system is in. Smoke detector, gas detector, and IR beams are strongly recommended to set in 24-H zone mode.
Connection & Disconnection
Maximum 40 sensors can be connected to the wireless strobe siren.
Connect with Remote Control
Press Learn button for 0.5 second till a beep is heard, the siren enters
connection status. Press any button in the remote control, the connection
succeeds when a beep is heard from siren.
Connect with Door Window Contact
Put the door window contact transmitter and magnet close in right position.
Press Learn button for 0.5 second till a beep is heard, the siren enters
connection status. Separate the magnet from the transmitter over 2 cm, the
connection succeeds when a beep is heard from siren.
Connect with PIR Motion Detector
Press Learn button for 0.5 second till a beep is heard, the siren enters
connection status. Press test button at back of the detector twice
continuously, the connection succeeds when a beep is heard from siren.
Connect with Other Accessories
Connect with other accessories is the same operation; please see details in
the user manuals for accessories.
Note: Once the siren is in connection status, please press Learn button again to exit. (A beep will be heard from siren) When 2 beeps are heard in connection status, means the sensor has been connected before.
Disconnection
Hold the Learn button in the siren till 2 beeps are heard to disconnect the
accessories from siren.
Installation Mode
Installation Mode is set for users to dismount or remount the siren without triggering the tamper switch. Thus not to disturb other people. Press button on the remote control continuously for 3 times, then the siren comes to installation mode after a long beep is heard. Any sensor or tamper triggered during installation mode will not result in siren hooting but 3 beeps will be heard instead.
Press button, the siren will exit from installation mode after a long beep is heard. Or the siren will automatically exit from installation mode when no operation is carried out within 10 minutes.
Note: Also you can press the tamper switch 7 times to enter service mode.
Installation
Please finish all the system setup on the PCB and enter into installation mode before installation.
- CD Hold the positioning paper in right place, stick the gradienter on the positioning paper to check and adjust the position.
- Install two screws into the top screw holes.
- Mount the bracket into the bottom screw holes and tighten with screws.
- Tear off the positioning paper.
- Mount the siren to the wall, tighten the screw and make sure the siren is well positioned.
Remote Control Operation
Work as a standalone alarm panel, user can use remote control to arm, disarm, and mute arm or disarm the siren. SOS emergency call can be realized.
Arm
Press on the remote control, the status LED indicator in the wireless control
flashes once to enter armed status and flashes once every 5 seconds later.
Disarm
Press on the remote control, the status LED indicator in the wireless control
flashes flashes twice and then goes out to enter disarmed status.
Home Arm (Part Arm)
When the system enters home armed status, all the sensors in normal zone is armed except those in home mode zone. While the home mode sensors are in disarmed status, users can move freely within the range of the disarmed area.Press
on the remote control, the status LED indicator in the wireless control flashes once to enter home armed status, and flashes once every 5 seconds later.
Note: The default zone setting of the PIR motion detector is home mode zone. When users press , the PIR motion detector enters disarmed status.
Emergency Call
Whenever you press the [SOS] on the remote control, the system will alarm
immediately and the alarm LED indicator will flash as well. After hooting
without disarming the system, the status LED indicator will flash once every 2
seconds.
Enter Connection Status Through Remote Control
This function is set for users to connect newly-purchased accessories without
dismounting the siren from the wall. When the siren is in installation mode,
press on the remote control continuously for 3 times, then the siren comes to
connection status after a long beep is heard. The siren will exit from
connection status when no operation is carried out in 15 seconds.
Zone Setting For Wireless Accessories
The zone setting is set through the inner jumpers of the sensors. If the zone
setting is changed, the accessories need to be reconnected with the control
panel. The accessory can be set in normal zone, home mode zone or 24-H zone.
- Normal Zone: In arm or home mode status, the system will alarm immediately once the sensors in normal zone is triggered.
- Home Mode Zone: In home mode status, the system will not alarm once the sensor in home mode zone is triggered.
- 24-H Zone: In any condition, the system will alarm immediately once the 24-H zone detector is triggered.
- How to set: Open the cover of the detector and change the array of jumpers to the corresponding zone position as below (Mind the direction of D0-D3).
Note: The default zone setting of PIR Motion Detector is Home Mode Zone. The default zone setting of Door/Window Contact is Normal Zone.
It is recommended to set smoke detector, gas detector or IR beam sensors in 24-H zone which offer full-day detection.
Specifications
- Power Supply DC 12V S00mA
- Backup Battery 18650 3.7V 1800mAh rechargeable lithium battery
- Maximum Alarm Current < 350mA
- Static Current < 14mA
- Wireless Receiving Distance < 80m (in open area)
- Operation Condition
- Temperature 0°C ~ +SS°C
- Relative Humidity< 80% (Non-condensing)
- Maximum Siren Volume lOSdB
- Battery Standby Time < 7 days
- Radio Frequency 315MHz or 433.92MHz (± 75KHz)
- Housing Material PC+ANTI-UV, ABS
- IP Rating IP54
- Dimensions (LxWx H) 245.2 x 227.5 x 72.4 mm
Ver: WS-280-UM-EN-Vl.3 2016 Chuango. All Rights Reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>