CHUANGO SPS-260 Solar-Powered Siren User Manual
- June 5, 2024
- CHUANGO
Table of Contents
SPS-260
Solar-Powered Siren
MULTILINGUAL
USER MANUAL
Product Overview
The solar-powered siren is a totally wireless siren, which can be installed in driveways, gardens, and all types of other external locations. The strobe siren is battery-powered and kept recharging by the built-in solar panel. The signal transmission is all by wireless radio frequency which achieves significantly wire-free transmission and enhances the flexibility of installation. The strobe outdoor siren can be used as a wireless siren by connecting to the control panel as well as a standalone alarm system to work with wireless accessories at the same frequency by learning.
PCB Layout
Note: The 9V battery is used to charge the 18650 battery in
case it is out of power/with low power after long-time storage. Use the 9V
battery to charge the 18650 battery for 12 hours and then remove the 9V
battery before installation. Note: The siren will sound immediately if the
tamper switch is triggered.
- The status LED light flashes every 5 seconds in Arm and Home Arm mode but doesn’t flash at all in Disarm mode.
Jumper Setup
Volume Setting
Siren Duration Setting
Note: To prevent possible hearing damage, it is suggested to avoid listening at a high volume level for long period.
Usage
Getting Started
- Load the 9V battery.
- Set the volume and duration of the siren.
- Start to use it by pressing the power button on.
Note: The battery is used to charge the 18650 battery in case it is out of power/with low power after a long time of storage. Use the 9V battery to charge 18650 for 12 hours and then remove the 9V battery before installation
When installed as part of a change Alarm System, the Siren must be paired to the Control Panel only.
The Siren will sound and the strobe lights will flash upon alarm activation. Disarming the System will stop the siren from sounding. If not disarmed the Siren Status Indicator will flash once every 2 seconds for one hour (visual notification of an alarm event).
Pairing to a Control Panel
- Press the Learn Button on the Solar Siren (0.5 seconds), the siren goes into Learn Mode after one beep is heard.
- Press the Arm or SOS Button on the Control Panel(or press the Arm on App if the panel does not have a button).
- The Siren is paired with Control Panel successfully after a second beep.
- If two beeps are heard, it is already linked.
To give up pairing the Control Panel, press the Learn Button (before step 2 is done) again to exit Learn Mode after one beep.
When installed as Siren only Alarm System (without a control panel). All of the Alarm Accessories must be paired to the Siren.
The Siren will sound and the strobe light will flash upon activation of a
connected Accessory.
Disarming the System will stop the siren from sounding. If not disarmed the
Siren Status Indicator will flash once every 2 seconds for one hour (visual
notification of an alarm event).
Pairing with Wireless Accessories
- Press the Learn Button (0.5 seconds), and the system goes into Learn Mode after one beep is heard.
- Press the Test Button on the additional Accessory or trigger the Accessory once.
- The Wireless Accessory is learned successfully after a second beep.
- If two beeps are heard, the accessory is already linked.
To give up pairing the Accessories, press the Learn Button (before step 2 is done) again to exit Learn Mode after one beep.
Note: Press and hold the Pair button of the wireless siren; the connection between the wireless siren and control panels (or accessories) is deleted when you hear a beep from the wireless siren.
Installation
Service Mode
Test Mode prevents the Siren’s tamper switch from triggering an alarm during
installation, maintenance, or when changing the battery.
When the remote control is connected with the siren, press [Disarm ] 3 times
successively (please make sure two beeps are heard at each time before
continuing the next press), the siren goes into service mode when a long beep
is heard.
During this period, the siren will not alarm but beep if the tamper switch or
the connected sensors are triggered. This brings you convenience on
installation.
Press [Arm ] on the remote control to exit service mode after a short beep.
Note: Also you can press the tamper switch 7 times to enter an
installation mode.
|
---|---
Remove the fixing screw from the bottom edge of the siren housing and
carefully remove the front cover.| Hold the mounting plate in position and
mark the positions of the four mounting holes. A spirit level placed on the
water-proof casing will ensure a perfect level.
|
Drill four holes and fit the wall plugs, and then fit supplied fixing screws
in the holes.| Hinge the front cover locating tabs over the top edge of the
backplate and carefully push the base of the siren cover into place. Secure
the siren cover in place by refitting the fixing screw in the bottom edge of
the cover.
Specifications
Backup Power| 18650 3.7 V 1800 mAh rechargeable lithium battery x 1 9 V 6F22
battery x 1
---|---
Solar Panel Output Current| 2000 LUX illumination ≥ 4 mA (in sunlight)
Maximum Alarm Current| < 500 mA
Wireless Receiving Distance| < 80m (in open area)
Operation Condition:| Temperature -20°C~+55°CRelative Humidity <80% (non-
condensing)
Maximum Siren Volume| 110 dB
Static Current| < 1 mA
Standby Time| < 45 days (fully charged)
Wireless Receiving Frequency| 433.92 MHz
Housing Material| PC + ABS + ANTI-UV
Size (L x W x H)| 309 x 230 x 79.7 mm
Printed in China
Ver: SPS-260-UM-ML-V1.0
© Chuango. All Rights Reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>