SUNRICHER SR-SB9101SAC-HP RF+Bluetooth AC In-Wall Switch Instruction Manual

: June 6, 2024
: SUNRICHER

Table of Contents

Function introduction
Product Data
Safety & Warnings
Product Dimension
Operation
Wiring Diagram
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

RF+Bluetooth AC In-wall Switch
70200014

Important: Read All Instructions Prior to Installation

Function introduction

Product Data

Input Voltage	Output Voltage	Output Current	Size(LxWxH)
100-240VAC	100-240VAC	1.8A max	45.5x45x20.3mm

Compatible Load Types

AC in-wall switch based on RF+Bluetooth Mesh
100-240VAC Wide Input and Output Voltage
Supports resistive loads and capacitive loads
1 Channel Output, Up to 400W
Input and Output with Screw Terminals, Safe and Reliable
Enables to control ON/OFF of connected load
Controlled through both smart App and remote controls, no gateway required
Easy & quick pairing to the smart App by simply pushing the reset button
Mesh network, much longer control distance, transmits received signal to neighbor devices
Up to 30m transmission distance between every two neighbor devices
Encrypted two-way communication, quick status feedback, safe & reliable data transmission
Compatible with universal RF+Bluetooth remotes, each LED controller can pair to the max. 8 remotes
Cloud control is available for remote access, works with Amazon Alexa and Google Home
Can be controlled by universal 8-230V input single wire push switch
Mini Size, Easy to be installed into a standard 86*86mm wall box
Radio Frequency : 2.4GHz
Waterproof grade: Ip20

Safety & Warnings

DO NOT install with power applied to the device.
DO NOT expose the device to moisture.

Product Dimension

Operation

Pair/delete the pairing with RF+Bluetooth remote

Do wiring according to the connection diagram.
Pair LED controller with RF+Bluetooth remote: please refer to the instruction of the remote that you would like to pair with.
Delete the pairing:
(1) Wire up the LED controller correctly, power on.
(2) Press and hold down the “ Reset” button on the controller for over 3 seconds (or reset the power of the device 8 times continuously if the button is not accessible to factory reset the device) until the connected light flashes, which means well deleted.
Note: factory resetting will restore all configured parameters of the device on the APP to the factory default setting.

Pair with smart APP

Do wiring according to the connection diagram.
Download EasyThings APP from IOS APP Store or Android Google Plays to your smartphone or tablet by searching “EasyThings”. (As shown in Figure 1)
Enable Bluetooth on your smartphone or tablet. (As shown in Figure 2)
Run Easythings APP, tap add button ” + ” on the APP to add a device, then choose “Discover devices” to discover the device, then short press the “Reset” button on the dimmer twice (or reset power of the dimmer twice continuously ) to set the device into pairing to APP mode. (As shown in Figure 3 & Figure 4 & Figure 5)
Note: multiple dimmers can be discovered by the APP at the same time.
Once the device/devices are discovered, tick the device/devices and tap the “Save” button, the device/devices will be added successfully. (as shown in Figure 6)

Controlled by a push switch:
Once connected with a push switch, click the push switch to switch ON/OFF.

Wiring Diagram

Notes for the diagrams:
L – terminal for live lead
N – terminal for neutral lead
Out – output terminal of the device (controlling connected light source)
+A1 – terminal for push switch
-A2 – terminal for grounding to the push switch connected to the device

With Single Push Switch
With Multiple Push Switches for Multiple Control Points

70200014

Documents / Resources

| SUNRICHER SR-SB9101SAC-HP RF+Bluetooth AC In-Wall Switch [pdf] Instruction Manual
SR-SB9101SAC-HP, RF Bluetooth AC In-Wall Switch, SR-SB9101SAC-HP RF Bluetooth AC In-Wall Switch
---|---