SUNRICHER SR-ZG9101SAC ZigBee 2-Gang In-Wall Switch Instructions

SUNRICHER SR-ZG9101SAC ZigBee 2-Gang In-Wall Switch Instructions

Important: Read All Instructions Prior to Installation

Function introduction

Product Data

Input Voltage| Output Voltage| Output Channel| Max. Load| Size(LxWxH)
---|---|---|---|---
100-240VAC| 100-240VAC| 2 Channels| Resistive load: max. 5.1A/CH

Capacitive load: max. 1.7A/CH

| 45.5x45x20.3mm

Compatible Load Types

Over Current Protection

• When connecting resistive load and total load is over 8.1A, the relay will be forced to off and protected.
• 2-gang ZigBee in-wall switch based on latest ZigBee 3.0 protocol
• 100-240VAC wide input and output voltage
• Supports resistive loads and capacitive loads
• 2 channels output, max. load 5.1A/CH
• Input and output with screw terminals, safe and reliable
• Enables to control ON/OFF of connected load
• ZigBee device with 2 endpoints which can be controlled separately
• ZigBee end device that supports Touchlink commissioning
• Can directly pair to a compatible ZigBee remote via Touchlink without coordinator
• Supports self-forming zigbee network without coordinator and add other devices to the network
• Supports find and bind mode to bind a ZigBee remote
• Supports zigbee green power and can bind max. 20 zigbee green power switches
• Compatible with universal ZigBee gateway products
• Can be controlled by universal single wire push switch, 2 channels can be controlled separately by 2 switches
• Active power and energy metering functionality
• Mini Size, Easy to be installed into a standard wall box
• Radio Frequency : 2.4GHz
• Waterproof grade: IP20

Safety & Warnings 

• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.

ZigBee Clusters the device supports are as follows:

Input Clusters

• 0x0000: Basic
• 0x0003: Identify
• 0x0004: Groups
• 0x0005: Scenes
• 0x0006: On/off
• 0x0702: Simple Metering
• 0x0b04: Electrical Measurement
• 0x0b05: Diagnostics

Output Clusters

• 0x0019: OTA

Operation

1. Do wiring according to connection diagram correctly.
2. This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee system.
3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)
   Step 1 : Remove the device from previous zigbee network if it has already been added to, otherwise pairing will fail. Please refer to the part “Factory Reset Manually”.
   Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as instructed by the controller.
   

TouchLink to a Zigbee Remote

Note

1. Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.
2. TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes.
3. To control by both gateway & remote, add remote and device to network first then TouchLink.
4. After TouchLink, the device can be controlled by the linked remotes.

Removed from a Zigbee Network through Coordinator or Hub Interface

Factory Reset Manually

Factory Reset through a Zigbee Remote (Touch Reset)

Note: Make sure the device already added to a network, the remote added to the same one or not added to any network.

Find and Bind Mode

Note: Make sure the device and remote already added to the same zigbee network.

Learning to a Zigbee Green Power Switch

Note: Each device can learn to max. 20 zigbee green power switches.

Delete Learning to a Zigbee Green Power Switch

Setup a Zigbee Network & Add Other Devices to the Network (No Coordinator Required)

Step 2 : Set another device or remote or touch panel into network pairing mode and pair to the network, refer to their manuals.
Step 3 : Pair more devices and remotes to the network as you would like, refer to their manuals.
Step 4 : Bind the added devices and remotes through Touchlink so that the devices can be controlled by the remotes, refer to their manuals.

Note

1. Each added device can link and be controlled by max. 30 added remotes.
2. Each added remote can link and control max. 30 added devices.

OTA

The device supports firmware updating through OTA, and will acquire new firmware from zigbee controller or hub every 10 minutes automatically.

Wiring Diagram

Notes for the diagrams:

L – terminal for live lead
N – terminal for neutral lead
S1 – terminal for switch key No. 1
S2 – terminal for switch key No. 2
L1 – output terminal no. 1 for light load
L2 – output terminal no. 2 for light load

Supported Switch Types:

The switch types this device supports can be configured by factory setting:

1. Push Switch (factory default setting)
2. Toggle On/Off Switch (can be configured by factory setting upon request)

With 1PC 2-Gang 1-Way Switch

2. With 2PCS 1-Gang 1-Way Switches

Product Dimension

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>