GE Lighting 93129825 Outdoor Wired Smart Camera Installation Guide
- June 6, 2024
- GE Lighting
Table of Contents
Outdoor Wired
Smart Camera
Installation Guide
Simple DIY Set Up
STEP 1
Plug in the CYNC™ Outdoor Wired Smart Camera in a convenient location
STEP 2
Download the Cync App, powered by Savant, on your smartphone
STEP 3
Add your Outdoor Wired Smart Camera to the Cync App
STEP 4
Install your Outdoor Wired Smart Camera
For set up help, visit
cyncsupport.gelighting.com or call
1-844-302-2943
GE is a trademark of General Electric Company. Used under trademark license.
Let’s Do It
INCLUDED
YOU’LL NEED
You Got This!
And we’re here to help.
For in-depth instructional videos and a guided tour through the installation,
go to cyncsupport.gelighting.com or call
1-844-302-2943.
NOTE: Please make sure your system is up-to-date, and you update the firmware when prompted for the best experience.
Choosing a Location
TIP: Plugin and hold the camera where you want it, and then have another person check the Cync App to see if the camera covers the preferred areas of your yard
Mount the Base
STEP 1
Choose the location where you wish to install your camera and verify your
camera is connected to Wi-Fi by checking the signal strength under settings in
the Cync App
STEP 2
Place the bracket where you wish to install the camera
STEP 3
Use the bracket to mark the holes
STEP 4
Drill holes with a ¼” drill bit
STEP 5
Screw in the mounting plate
Attach the Camera
STEP 1
Identify the two notches at the bottom of the mounting plate
STEP 2
Route the cord through the notches so that the cord going to the outlet is
flush with the wall
STEP 3
Align the red notch on the base of your camera with the red notch on the
mounting plate
STEP 4
Slide the camera base onto the mounting plate until it clicks in place
Adjust the Position, Plug In Camera & Finish Set-Up
STEP 1
Plug your camera into the desired outlet
STEP 2
Optional: Attach your cord to the siding or ceiling for more discreet mounting
STEP 3
Adjust the camera to the desired angle (use the camera view in the Cync App to
verify the view before locking the ball joint)
STEP 4
Turn the camera neck clockwise to tighten the ball joint and lock your camera
in place
You’re all set!
Use the Cync App to check out your camera’s live feed and select your motion
settings and zones under your camera’s settings.
Congratulations!
You’ve completed the Cync Outdoor Wired Smart Camera installation
Additional Information and Warnings
FCC Statement
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
The device must not be co-located or operating in conjunction with any other
antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions : (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC RF Radiation Exposure Statement Caution:
To maintain compliance with the FCC’s RF exposure guidelines, place the
product at least 20cm from nearby persons.
IC statement
This device complies with RSS247 of Industry Canada. Cet appareil se conforme
à RSS247 de Canada d’Industrie. This device complies with Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation of the device. appareils radio exempts de licence. Son
fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne
doit pas produire de brouillage prejudiciable, et (2) ce dispositif doit
accepter tout brouillage recu, y compris un brouillage susceptible de
provoquer un fonctionnement indesirable.
The device must not be co-located or operating in conjunction with any other
antenna or transmitter.
Like your new Outdoor Wired Smart Camera? Share your experience!
Leave a review of where you purchased the product.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>