intez ze PIKO 3 TWS Earphones User Manual
- June 5, 2024
- intez ze
Table of Contents
intez ze PIKO 3 TWS Earphones
**User Manual**
Introduction
Our passion & your joy
Only together we are INTEZZE
We design all our models to serve reliably for several years, but sometimes something can go wrong. Therefore, we recommend that you take a few minutes to read the following pages, where you will learn, among other things, how to prevent faults and how to deal with connection issues.
Earphone description
- Touch buttons
- Microphone and LED
- Ear tips
- LED charging indication
- Charging pins
- Charging connector (rear)
ON/OFF
ATTENTION! Fully charge the earphones together with the case prior to first use.
The earphones turn on automatically when you pull them out of the case (a confirmation tone sounds in both of them). Likewise, they switch off automatically when stored back in the case. They also turn off automatically after two minutes when they are not connected to any device.
Manual switch on
Hold down both touchpads for about 3 seconds until the power-on tone sounds.
Manual switch off
Hold down both touchpads for about 5 seconds until the power-off tone sounds.
Pairing
Prior to the first use with every device, it is necessary to pair the earphones. The next time you use the same device, pairing is no longer necessary and it connects automatically when you pull the earphones out of the case.
Pairing procedure
- Remove both earphones from the case and wait a few seconds for both of them to turn on (one of the earphones will flash alternately red and blue).
- Turn on Bluetooth on your phone and look for Intezze PIKO 3 in Available BT Devices. Confirm pairing.
- Successful pairing is confirmed by a tone and the flashing LED turns off.
Operation
Button = earbud touch button, L = left earbud, R = right earbud
Listening to music
Phone calls
Charging
Charging the earphones
The earphones start charging automatically when they are inserted into the case (indicated by the red LED on the earphones). The case must be at least partially charged to begin charging.
Charging the case
Charge the charging case using the included USB-C cable by connecting it to a phone charger or other powered USB connector. Connect the charging cable to the connector on the back of the charging case.
Pairing one earphone (MONO)
- Pair both earphones with your phone as described in the Pairing chapter.
- Insert both earphones back into the case.
- Pull out only one of the earphones after a moment. It will automatically connect to the paired phone after a few seconds.
If you subsequently pull out the second earphone within range from the case, it will also connect automatically and playing will continue in both earphones.
You cannot use the earphone volume setting in single earphone mode.
RESET function
If both earphones cannot be connected to your phone, we recommend resetting the earphones as follows. After a successful reset, all previously paired devices will be deleted from the earphone memory.
- On your phone, remove the PIKO 3 earphones from the list of previously paired BT devices and turn off the Bluetooth function.
- Remove both earphones from the case (or put them into your ears). When the earphones turn on automatically, tap the buttons on both earphones three times at the same time. A confirmation double beep sounds in the earphones.
- The earphones are now reset and have to be paired with the phone again according to the procedure in the “Pairing” chapter.
LED indication on the earphones
LED indication on the case
Warning
- Fully charge the case together with the earphones prior to first use.
- If you do not use the earphones for a long time, charge them regularly together with the case to avoid damaging the batteries (shortening their service life).
- Keep the set volume at the lowest possible level. Listening to loud volumes for an extended period may damage your hearing irreversibly!
- Children must be supervised by an adult when using the earphones. Risk of swallowing small parts.
- Do not expose the earphones to water for extended periods. The earphones are not designed for swimming, showering, or diving.
- Using the earphones in a very dusty or humid environment may result in damage to the earphones.
- Only use a slightly damp cloth for cleaning.
- Do not use the earphones out of the allowed temperature range of -15 °C to +50 °C.
- Do not charge the case or earphones in places with a temperature lower than 0 °C.
- Do not expose the earphones or case to direct sunlight for extended periods.
- Never disassemble or otherwise repair the earphones yourself.
- Keep the earphone grille clean on both earphones in order to avoid sound degradation.
- Follow the applicable laws and regulations when using earphones while driving.
- Do not use earphones in situations where it is necessary to hear your surroundings and have an overview of what is happening around you.
Warranty conditions
The warranty does not cover the following situations:
- Damage caused by tampering with the device.
- Filters clogged by earwax (may not be properly visible) or otherwise dirty. Cleaning must be performed by an authorised service provider and is charged.
- Earphones with the earphone duct filters removed.
- Physical damage to the earphones caused by a fall or impact.
- Damage caused by force majeure.
Content subject to change
Content subject to change
www.intezze.cz/www.intezze.com
References
- Proč bezdrátová sluchátka TWS | Intezze
- Proč bezdrátová sluchátka TWS | Intezze
- Proč bezdrátová sluchátka TWS | Intezze
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>