adastra IW30B In-Wall Bluetooth Amplifier User Manual

IW30B
In-wall Bluetooth® Amplifier
Item ref: 953.091UK
User Manual

Version 1.2

Caution: Please read this manual carefully before operating Damage caused by misuse is not covered by the warranty

Introduction

Thank you for choosing the Adastra IW30B in-wall amplifier for your discreet audio installation. This unit is designed to power wall or ceiling-mounted speakers and receive audio via Bluetooth. Please read this manual to gain the best results from your product and avoid damage through misuse.

SAFETY SYMBOL AND MESSAGE CONVENTIONS

CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN| AVIS
RISQUE DE CHOC ELECTRIQUE NE PAS
OUVRIR
---|---

**** This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

Warning

To prevent the risk of fire or electric shock, do not expose any components to rain or moisture. If liquids are spilled on the casing, stop using immediately, allow the unit to dry out, and have checked by qualified personnel before further use. Avoid impact, extreme pressure, or heavy vibration to the case.
No user-serviceable parts inside ­ Do not open the case ­ refer all servicing to qualified service personnel.

Safety

• Check for correct mains voltage before connecting the power adaptor
• Use only the power adaptor provided or an identical replacement

Placement

• The IW30B can be installed in a ceiling or stud wall to power flush or surface mount speakers
• The IW30B can also be surface mounted if necessary
• Ensure adequate ventilation for cooling and keep away from combustible material or moisture
• Ensure that the IW30B is within the Bluetooth connection range of the sending device

Cleaning

• Use a soft cloth with a neutral detergent to clean the housing as required
• Use a vacuum cleaner to clear apertures and controls any dust or debris build-ups
• Do not use solvents for cleaning the unit

Connections

Installation

Locate the IW30B in the ceiling, wall or on the surface required. Tabs at each end of the housing can be used for securing with screws.
Connect speakers using the supplied wires or equivalent by connecting “+” and “-” on the speaker to the relevant connection on the IW30B. The speaker connections are via screw
terminals on a Euroblock, which can be removed for easy access whilst making connections.

Important:
Ensure that the load is no lower than 4 for each output. (e.g. 2 x 4 speakers… or… 2 pairs of 8 speakers wired in parallel) Ensure that the speakers can handle 15W from each output.

If the IW30B is to be used with a wired audio line-level input (instead of Bluetooth), connect this to the Euroblock terminals labeled “AUX IN” as shown on the Connections diagram above.

Left positive connection (Left+) should be connected to “L”
Right positive connection (Right+) should be connected to “R”
Both negative connections (Left- and Right-) should be connected to “G”
(G is the terminal for Ground connection ­ common for both Left and Right signals)

Likewise, the Bluetooth or Aux input can be relayed to further IW30B or other amplifiers by connecting a line-level output from the Euroblock terminals labeled “AUX OUT”

AUX IN and AUX OUT connections should be made using the shielded stereo audio cable and not the speaker cable.

Operation

When powered up, the IW30B will be open for Bluetooth pairing.
(a small LED will flash inside the housing)
Ensure that only the first IW30B in an AUX OUT-IN daisy chain is powered-up initially.
This will ensure that all of the amps in the daisy chain receive the same audio.

Search available Bluetooth devices on your smartphone or other sending device for a device with Bluetooth ID “IW30B-” (where is a unique ID number for each unit)
Select to pair and connect with this ID (rename if required on Android)

When paired and connected, set the volume low on the smartphone or other sending device and play a track to check the sound through the speakers.
Power down the IW30B when not in use and isolate from the mains if not used for long periods of time.

Specifications

Disposal: The “Crossed Wheelie Bin” symbol on the product means that the product is classed as Electrical or Electronic equipment and should not be disposed of with other household or commercial waste at the end of its useful life. The goods must be disposed of according to your local council guidelines.

Hereby, AVSL Group Ltd. declares that the radio equipment type 953.091UK is in compliance with Directive2014/53/EU

The full text of the EU declaration of conformity is available at the following internet address: http://www.avsl.com/assets/exportdoc/9/5/953091UK%20CE.pdf

Errors and omissions excepted. Copyright© 2021. AVSL Group Ltd.
Unit 2-4 Bridgewater Park, Taylor Rd. Manchester. M41 7JQ
AVSL (EUROPE) Ltd, Unit 3D North Point House, North Point Business Park, New Mallow Road, Cork, Ireland

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>