SubZero SXSW-C12SA Active Subwoofer User Manual
- June 6, 2024
- SUBZERO
Table of Contents
ACTIVE
SUBWOOFER
SZSW-C12SA / SZSW-C15SA / SZSW-C18SA
USER MANUAL
WARNING!
Do not open the cover. No user-serviceable parts inside. Refer servicing to
qualified service personnel Do not place the product in a location near a heat
source such as a radiator, or in an area subject to direct sunlight, excessive
dust, mechanical vibration, or shock
The product must not be exposed to dripping or splashing and no objects filled
with liquids, such as vases, shall be placed on the product
No naked flame sources, such as lighted candles, should be placed on the
product Allow adequate air circulation and avoid obstructing vents (if
present) to prevent internal heat build-up. The ventilation must not be
impeded by covering the appliance with items such as newspapers, tablecloths,
curtains, etc.
The mains plug is used to disconnect the appliance from the mains supply.
Ensure that the main outlet is easily-accessible and remove the plug from the
main outlet if you notice any abnormality with the appliance.
INTRODUCTION
Thank you for purchasing the SubZero Active PA Subwoofer. To get the most out of your product, please read this manual carefully.
FEATURES
- Clear and balanced sound.
- High-quality Class D amplifier.
- Crossover control @ 80Hz and 125Hz.
- 180º phase function.
- High-durable wood and carpet design.
- Left and right input channels with XLR + 6.3mm Jack combi connections.
- Left and right link and output XLR channels.
FUNCTIONS
BACK PANEL
-
LINE IN
Input connection using either XLR or 6.3mm TRS Jack. Connect the outputs from a mixer or PA speaker to this input. -
LINK
Full range output connection using XLR. Connect PA speakers from this output. -
OUTPUT
Post-crossover, low range output. Connect further subwoofers to this output. -
180º phase reverse function.
If you find that the overall sound seems low volume or thin when using the subwoofer in conjunction with a PA speaker, try using this function. REVERSE PHASE SWITCH -
LEDs
SIG: When lit, the speaker is receiving an input signal.
: When lit, the power is on. -
MASTER LEVEL
Adjust the overall output volume. -
CROSS OVER CONTROL
Change the high cut point of the low pass filter to either 80Hz or 125Hz. -
FUSE SWITCH
Change between 115V and 230V input power. Please ensure the correct rating is used for your region. -
POWER SWITCH
Turns the speaker on or off. -
POWER INPUT
Connect the provided AC power cable here.
SPECIFICATIONS
SZS-C12SA
Power Rating ………….RMS: 300W Peak: 420W Max: 1200W
Woofer ……………… 12” with 2.5” voice coil and 50oz ferrite magnet
Amplifier …………….Class D
Impedance …………..4ohms
Sensitivity …………….96dB
Max SPL Rating ………..123dB
Frequency Response ……40Hz – 150Hz
AC Power Input ………..220-240V
Fuse Type …………….3.15A
Power Consumption ……360W
Weight ………………18kg
Dimensions …………..48.5 x 35.5 x 45cm
SZS-C15SA
Power Rating ………….RMS: 350W Peak: 500W Max: 1400W
Woofer ……………… 15” with 3” voice coil and 60oz ferrite magnet
Amplifier …………….Class D
Impedance …………..4ohms
Sensitivity …………….96dB
Max SPL Rating ………..124dB
Frequency Response ……40Hz – 150Hz
AC Power Input ………..220-240V
Fuse Type …………….3.15A
Power Consumption ……410W
Weight ………………24.3kg
Dimensions …………..56.5 x 43 x 54cm
SZS-C18SA
Power Rating ………….RMS: 350W Peak: 500W Max: 1400W
Woofer ……………… 18” with 3” voice coil and 80oz ferrite magnet
Amplifier …………….Class D
Impedance …………..4ohms
Sensitivity …………….97dB
Max SPL Rating ………..125dB
Frequency Response ……40Hz – 150Hz
AC Power Input ………..220-240V
Fuse Type …………….3.15A
Power Consumption ……410W
Weight ………………32kg
Dimensions …………..63.5 x 50.5 x 61.5cm
KETTLESTRING LANE | YORK | YO30 4XF | UNITED KINGDOM
If you have any more questions about this product, please do not hesitate to contact the Gear4music Customer Service Team on: +44 (0) 330 365 4444 or info@gear4music.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>