SubZero SZ-SATURN-15VRH Saturn 15VRH Amplifier Head User Manual

SubZero SZ-SATURN-15VRH Saturn 15VRH Amplifier Head

INTRODUCTION

Thank you for purchasing the SubZero Saturn 15VRH amp head. To get the most out of your product, please read this manual carefully.

BOX CONTENTS

• SubZero Saturn 15VRH amplifier head.
• UK mains cable.
• EU mains cable.

PRODUCT FEATURES

• All tube 15W architecture.
• Switchable 1W and 15W outputs.
• Reverb and effects loop.
• 3-Band EQ with shape control.

SPECIFICATIONS

• Input Power: 220-240VAC, 50/60Hz
• Fuse: F1.6A, 250V
• Power Consumption: 50W Max
• Preamp Tube: 3x 12AX7
• Power Tube: .2x EL84
• Input Impedance: .1MΩ
• Speaker Output: Max 15W RMS
• Speaker Output
• Impedance: Minimum 8Ω
• Frequency Range: 80Hz – 10kHz
• S/N Ration: -75dB
• THD: 0.5%
• Dimensions: 436242204mm
• Weight: 9.0kg

FUNCTIONS

1. INPUT CONNECTOR
   Connect your guitar to this connector using a 6.3mm TS jack cable.

2. HIGH/LOW SWITCH
   Switch between 1W (low) and 15W (high) power output using this switch.

3. REVERB CONTROL
   Adjust this dial to control the amount of reverb is added to the output signal. Turning fully anticlockwise will add no reverb to the output signal.

4. TREBLE CONTROL
   Adjust this dial to control the amount of treble (high frequency) sent to the speaker output.

5. MIDDLE CONTROL
   Adjust this dial to control the amount of midrange frequency sent to the speaker output.

6. BASS CONTROL
   Adjust this dial to control the amount of bass (low frequency) sent to the speaker output.

7. TONE CONTROL
   Adjust the tone of your amplifier using this dial. Fully anticlockwise will produce a thinner sound, fully clockwise will produce a broader sound.

8. VOLUME CONTROL
   Adjust this dial to control the overall volume sent to the speaker output connector on the rear of the amplifier.

9. GAIN CONTROL
   Adjust this dial to increase the input gain from the guitar. More gain will create a more distorted sound.

10. STANDBY LIGHT
    This light will illuminate when the amplifier is switched on.

11. POWER SWITCH
    This switch turns the amplifier on and off. When the amplifier is switched on, allow a moment for the tubes to warm up before playing. This will increase the lifespan of the tubes and create a better output sound.

12. MAINS POWER CONNECTOR
    Connect the amplifier to the mains power using this connector. Only use the mains cable provided with the product.

13. REVERB FOOTSWITCH CONNECTOR
    Connect a one button footswitch with a 6.3mm TS jack cable to this connector (not included) to turn the reverb on and off remotely.

14. EFFECTS LOOP (RETURN) CONNECTOR
    Connect the output of an external effects processor to this connector using a 6.3mm TS jack cable.

15. EFFECTS LOOP (SEND) CONNECTOR
    Connect the input of an external effects processor to this connector using a 6.3mm TS jack cable.

16. SPEAKER OUT CONNECTOR
    Connect an external speaker to this connector using a 6.3 TS speaker jack cable.
    NOTE: This connection outputs at an amplifier level. It is recommended to use a speaker jack cable capable of carrying the required load.

WARNING!

• Do not open cover. No user-serviceable parts inside. Refer servicing to qualified service personnel
• Do not place the product in a location near a heat source such as a radiator, or in an area subject to direct sunlight, excessive dust, mechanical vibration or shock
• The product must not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the product No naked flame sources, such as lighted candles, should be placed on the product

If you have any more questions about this product, please do not hesitate to contact the Gear4music Customer Service Team on: +44 (0) 330 365 4444 or info@gear4music.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>