Subzero SW-P15X ACTIVE DSP SUBWOOFER User Manual

: June 5, 2024
: SUBZERO

Table of Contents

****
Read User Manual Online (PDF format)
Download This Manual (PDF format)

****

Subzero SW-P15X ACTIVE DSP SUBWOOFER **

WARNING!**

Do not open the cover. No user-serviceable parts inside. Refer servicing to qualified service personnel
Do not place the product in a location near a heat source such as a radiator, or in an area subject to direct sunlight, excessive dust, mechanical vibration or shock
The product must not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the product
No naked flame sources, such as lighted candles, should be placed on the product
Allow adequate air circulation and avoid obstructing vents (if present) to prevent internal heat build-up. The ventilation must not be impeded by covering the appliance with items such as newspapers, tablecloths, curtains, etc.
The mains plug is used to disconnect the appliance from the mains supply. Ensure that the main outlet is easily-accessible and remove the plug from the main outlet if you notice any abnormality with the appliance.

INTRODUCTION

Thank you for purchasing the SubZero Active DSP Subwoofer.
To help you get the most out of your new product, please read this manual carefully.

BOX CONTENTS

1 x SZSW-P15X / SZSW-P18X
1 x UK power cable
1 x EU power cable
1 x User manual

FEATURES

Professional subwoofer with digital processing to optimize your sound.
A high-quality woofer and voice coil gives you deep and powerful bass.
Features two XLR/jack combo input channels and a crossover output.
Includes 35mm M20 threaded speaker pole mount.

OVERVIEW

Subzero SW-P15X ACTIVE DSP SUBWOOFER FIG
1

MASTER CONTROL
Used to adjust the master volume.
When the dial is pressed you are able to cycle through and select DSP modes in the DSP menu.
INPUT
Combination XLR / Jack input to receive a connection from a mixer or amp.
OUTPUT
Audio signals routed from each input are sent through this output. This is a line-level signal.
POWER SWITCH
Used to turn the speaker ON or OFF.
IEC SOCKET
For connecting to a mains power supply using the supplied IEC power cable.

A fuse is included within the IEC socket for added protection – if the fuse fails ensure it is replaced with a fuse of the same type and rating.

FEATURES

DSP FEATURES

DEFAULT DISPLAY
The default display (right) is shown when you are not making any adjustments. The top line shows the output volume in dB. Rotate the MASTER knob to adjust the level.

The signal level is shown as a horizontal bar graph. ‘CLIP’ appears in the box at the right-hand side of the graph if the input signal level exceeds
the clipping level. Reduce the input level if this happens.

USING THE MENU
Press the MASTER knob to access the DSP menu. The scroll bar at the right-hand side of the display shows the current position in the menu list.
The currently selected menu item is highlighted.
Rotate the MASTER knob to scroll through the menu items. When the desired item is highlighted, press the MASTER knob to select it. The parameter value that you will be adjusting will be highlighted.

Rotate the MASTER knob to scroll through the available values then press the MASTER knob again to confirm. The highlight will then return to the current menu item.

To exit from the menu, scroll up or down to ‘EXIT’ and press the MASTER knob, or just wait a few seconds and the display will change back to the default screen automatically.

LOCATION
This allows you to tailor the speaker for either professional or personal listening applications.

Normal
Monitor

INFO

Displays DSP firmware version number.

EXIT

Exits the menu.

MODE
You’ll find these modes particularly useful for achieving great sounds instantly in a variety of scenarios.

Music (default)
Live
DJ

HIGH CUT

80Hz to 150Hz (default)

PHASE

Normal (default)
Reverse

LED MODE
This mode allows you to choose the function of the front-mounted LED.

OFF – LED is not illuminated.
ON – LED is Illuminated when the speaker is powered on (default).
LIMITER – shows when the output level has exceeded the maximum limit.

LCD DIM

OFF – LCD screen remains fully illuminated (default).
ON – LCD screen dims slightly a few seconds after the last operation.

BRIGHT

Adjusts display brightness in increments between 0-10.

CONTRAST

Adjusts display contrast in increments between 0-10. Adjust for optimal viewing at different angles.

RESET

Reset all settings to factory default. Rotate the MASTER knob to select Yes or No, then press the knob to confirm.

SPECIFICATIONS

SZSW-P15X
Two Way, Bi-Amped, Bass Reflex Active Subwoofer On-Board Digital Sound Processor
Frequency Response …35Hz -150Hz
Power Output ……… 800W RMS / 1150W Peak / 3200W MAX
SPL ………………128dB Max
Driver ……………. 15” Woofer with 4” Voice Coil
Amplifier Type ………Class D
Connectors ……….. Input 1 + 2 – Combi
Output – XLR
Material …………..18mm Plywood
Finish ……………. Matte Black Handles …………..2 x Side
Pole Socket ………..35mm & M20 Pole Socket
Dimensions ………..621mm x 480mm x 620mm
Weight ……………39Kg

SZSW-P18X
Two Way, Bi-Amped, Bass Reflex Active Subwoofer On-Board Digital Sound Processor
Frequency Response … 30Hz -150Hz
Power Output ……… 800W RMS /1600W Peak / 3200 Max
SPL ……………… 130dB Max
Driver ……………. 18” Woofer with 4” Voice Coil
Amplifier Type ……… Class D
Connectors ……….. Input 1 + 2 – Combi
Output – XLR
Material ………….. 18mm Plywood
Finish ……………. Matte Black Handles ………….. 2 x Side
Pole Socket ……….. 35mm & M20 Pole Socket
Dimensions ……….. 775 x 655 x 790mm
Weight …………… 46Kg