SubZero SZ-SATURN-15VRC Combo Amplifier User Manual
- June 5, 2024
- SUBZERO
Table of Contents
SubZero SZ-SATURN-15VRC Combo Amplifier
INTRODUCTION
Thank you for purchasing the SubZero Saturn 15VRC 15W combo amplifier. To get the most out of your product, please read this manual carefully.
BOX CONTENTS
- SubZero Saturn 15VRC amplifier.
- UK mains cable.
- EU mains cable.
PRODUCT FEATURES
- Celestion seventy80 Speaker.
- All tube 15W architecture.
- Switchable 1W and 15W outputs.
- Reverb and effects loop.
SPECIFICATIONS
- Input Power ………..220-240VAC, 50/60Hz
- Fuse ……………..F1.6A, 250V
- Power Consumption …50W
- Max Speaker …………..Celestion seventy80
- Preamp Tube ……….3x 12AX7
- Power Tube ………..2x EL84
- Input Impedance ……1MΩ
- Speaker Output …….Max 15W RMS
- Speaker Output
- Impedance ………..Minimum 8Ω
- Frequency Range ……80Hz – 10kHz
- S/N Ration …………-75dB
- THD. . . . . . . . . . . . . . . . . . 0.5%
- Dimensions ………..427435235mm
- Weight ……………11.5kg
FUNCTIONS
-
POWER SWITCH
This switch turns the amplifier on and off. When the amplifier is switched on, allow a moment for the tubes to warm up before playing. This will increase the lifespan of the tubes and create a better output sound. -
STANDBY LIGHT
This light will illuminate when the amplifier is switched on. -
GAIN CONTROL
Adjust this dial to increase the input gain from the guitar. More gain will create a more distorted sound. -
VOLUME CONTROL
Adjust this dial to control the overall output sound from the amplifier. This dial will also affect the volume sent to the speaker output connector on the rear of the amplifier. -
TONE CONTROL
Adjust the tone of your amplifier using this dial. Fully anticlockwise will produce a thinner sound, fully clockwise will produce a broader sound. -
BASS CONTROL
Adjust this dial to control the amount of bass (low frequency) sent to the speaker output. -
MIDDLE CONTROL
Adjust this dial to control the amount of mid-range frequency sent to the speaker output. -
TREBLE CONTROL
Adjust this dial to control the amount of treble (high frequency) sent to the speaker output. -
REVERB CONTROL
Adjust this dial to control the amount of reverb added to the output signal. Turning fully anticlockwise will add no reverb to the output signal. -
HIGH/LOW SWITCH
Switch between 1W (low) and 15W (high) power output using this switch. -
INPUT CONNECTOR
Connect your guitar to this connector using a 6.3mm TS jack cable. -
SPEAKER OUT CONNECTOR
Connect an external speaker to this connector using a 6.3mm TS speaker jack cable. -
EFFECTS LOOP (SEND) CONNECTOR
Connect the input of an external effects processor to this connector using a 6.3mm TS jack cable. -
EFFECTS LOOP (RETURN) CONNECTOR
Connect the output of an external effects processor to this connector using a 6.3mm TS jack cable. -
REVERB FOOTSWITCH CONNECTOR
Connect a one-button footswitch with a 6.3mm TS jack cable to this connector (not included) to turn the reverb on and off remotely. -
MAINS POWER CONNECTOR
Connect the amplifier to the mains power using this connector. Only use the mains cable provided with the product.
WARNING!
Do not open cover. No user-serviceable parts inside. Refer servicing to
qualified service personnel Do not place the product in a location near a heat
source such as a radiator, or in an area subject to direct sunlight, excessive
dust, mechanical vibration or shock The product must not be exposed to
dripping or splashing and no objects filled with liquids, such as vases, shall
be placed on the product No naked flame sources, such as lighted candles,
should be placed on the product The mains plug is used to disconnect the
appliance from the mains supply. Ensure that the main outlet is easily
accessible and remove the plug from the main outlet if you notice any
abnormality with the appliance.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>