OPTICIS DPFX-300-TR DisplayPort 1.2 Detachable Extender User Manual
- June 6, 2024
- opticis
Table of Contents
OPTICIS DPFX-300-TR DisplayPort 1.2 Detachable Extender
Welcome!
Congratulat ions on your purchase of the one (1) fiber DisplayPort extender,
DPFX-300- TR. This manual contains information that will assist you in
installing and operating the product.
Product Description
DisplayPor t 1.2 one(1) fiber optical detachable extender, DPFX-300, extends DisplayPor t 1.2 signal up to 200m (656feet) and transmits 4K UHD (4096×2160) at 60Hz over one(1) LC multi-mode fiber. Leading-edge technology of Opticis allows long distance transmission of 4K signal without any video/a udio degradation.
DPFX-300- TR is designed compact enough to be fitted into various installation
environment s. It gives slim, light, easy installation with perfect electrical
isolation, b ut without electrical hazard and interference.
Between T ransmitter (DPFX-300-Tx) and receiver (DPFX-300-Rx), pure fiber
connection b y single LC fiber connector gives clean, secure and easy
installation. Additional DPFX-300-TR can interoperate with DPFX-700 as a pair.
DPFX-300- TR can be operated by USB power without external DC power adapter w ith plugging micro USB (DPFX-300 module side) – USB (source/dis play devices side) cable which is supplied in shipping group.
System Requirements for Setup
- Hardware requirements
- You must have a DisplayPort source and display. It should support the maximum graphic resolution feature of displays to be connected.
- No special requirements of memory size, CPU speed and chipsets, if you’ve already properly installed your DisplayPort systems or graphic cards.
- Proper initial trial of the entire platform with its application using a short length copper cable is recommended prior to installation with the optical link.
- Software requirements
- No special restrictions, if you’ve already properly installed your DisplayPort systems.
- Power Technical Advisory
- Enclosed Power Adaptors and USB cables supply power to both Transmitter and Receiver.
- Connection Advisory
- It is highly recommended that DisplayPort source is directly connected into DisplayPort display output via DPFX-300-TR without connection to incompatible distributor, switcher and selector.
The Shipping Group of DPFX-300-TR;
- One (1) Transmitter (Tx) and One (1) Receiver (Rx)
- One (1) 0.2m Male to Female DisplayPort copper cable
- Two (2) Micro USB to USB cables
- Two (2) 5V 1A power adapter
- User Manual
- Default connection is direct connection to both source (Tx side) and display (RX side)
- If direct connection is impracticable, 0.2m DisplayPort copper cable
Installation
Important: Please keep the installation procedure below. Improper or no
operation may result if the start-up sequence is not correctly followed.
Step 1
Carefully unpack the contents in the shipping group.
Step 2
Power on the DisplayPort source and display. Both the transmitter and receiver
will be turned on by 3.3V from pin #20 of DisplayPort interface. The USB power
is recommended for the stable power supply for both the transmitter and
receiver.
Step 3
The Power LED will be turned on when DPFX-300-TR is connected to DisplayPort
interface of signal source and display and the Status LED will blink three (3)
times. Then the Status LED will blink again when the whole connection is made.
Step 4
Connect one (1) LC optical fiber between the transmitter and the receiver.
Ensure the connectors are fully engaged and then, the top LED will begin to
blink regularly.
Note1: Please DO NOT look directly into the LC receptacles of the
Transmitter when it is powered on. Although this product is regulated strictly
enough to operate under the LASER Class I, classified by CDRH/FDA for eye
safety, it is not recommended to do so.
Note2: The maximum extension length by OM3 fiber is 200 meters (656ft.).
Note3: it is recommended NOT to use any intermediate cable or adapter
between them to avoid undesirable performance degradation.
Step 5
Connect the transmitter (DPFX-300-Tx) to the DisplayPort source.
Step 6
Connect the receiver (DPFX-300-Rx) to the DisplayPort display.
Note: If the connectors are fully engaged, the bottom LED will turn on.
Step 7
If the system does not work properly, go to the page 1-5 for trouble shooting.
Troubleshooting
The display shows only black screen.
- Ensure that all plugs and jacks used by USB power supplies are firmly connected. Ensure that the LED is ON.
- Ensure that the DisplayPort is firmly plugged in to the DisplayPort source and display.
- Ensure that the transmitter and receiver modules plugged correctly to the source and display, respectively.
- Check if the DisplayPort source and display are powered on and properly booted.
- Reset the system by de-plugging and re-plugging the transmitter DisplayPort or receiver DisplayPort, or by de-plugging and re-plugging the USB power cables that are plugged of the transmitter and receiver module
- Re-boot up the system while connecting the module.
Screen is distorted or displays noises.
- Check if the graphic resolution is properly set. Go to the display properties and tap the settings. Ensure that the resolution sets less than WQUXGA (3840×2400) at 60Hz refresh ratio.
- Reset the system
- Power down, disconnect and reconnect the optical system cable or USB power adaptors, and power up
Maintenance
No special maintenance is required for the optical system cables and power
supplies. Ensure that the cables and power modules are stored or used in a
benign environment free from liquid or dirt contamination.
There are no user serviceable parts. Refer all service and repair issues to
Opticis or its authorized distributor.
Technical Support and Service
For commercial or general product support, contact your reseller. For
technical service, contact Opticis by email
techsupp@opticis.com or visit its website at
www.opticis.com
Product Specifications
- Compliance with DisplayPort standard: supports DisplayPort 1.2a
- Extension limit: 200m (656feet) for 4K (4096×2160) at 60 Hz refresh rate over one (1) LC OM3 fiber (50/125um).
- Graphic Transmission Bandwidth: Supports total data rate 21.6Gbps (5.4Gbps per lane).
Graphic Transmission Bandwidth: Supports total data rate 21.6Gbps (5.4Gbps per lane).
- Selectable Option: full interoperable with DPFX-700-TR as a pair.
- Supports auxiliary /l²C channel over fiber
- Support Multi-Stream Transport
- Mechanical specifications of transmitter and receiver
- Dimensions(WDH): 22mm x 67mm x 14mm
- Environmental Specifications
- Operating temperature: 0°C to 50°C
- Storage temperature: -30°C to 70°C
- Humidity: 10% to 85%
AC/DC Power Adapter
- Power Input: AC 100-240V, 50/60Hz.
- Power Output: +5 V, 1A SMPS DC-power Adapter
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>