opticis HDFX-500-TR One Fiber 4K60HZ HDMI 2.0 Extender User Manual
- June 6, 2024
- opticis
Table of Contents
opticis HDFX-500-TR One Fiber 4K60HZ HDMI 2.0 Extender
Welcome !
Congratulations on your purchase of the one (1) fibers HDMI 2.0 extender,
HDFX-500- TR. This manual contains information that will assist you in
installing an d operating the product.
Product Description
HDMI 2.0 optical fiber detachable extender, HDFX-500-TR, extends HDMI 2.0 signal up to 200m (656feet) and transmits 4K UHD (4096×2160) at 60Hz over one LC multi-mode fiber. Leading-edge technology of Optics allows long-distance transmission of 4K signal without any video/audio degradation.
- HDFX-500- TR is designed to be compact enough to be fitted into various installation environments. It gives slim, light, easy installation with perfect electrical isolation, but without electrical hazards and interference.
- HDFX-500- TR adopted a High-Retention HDMI connector, which allows for more retention force than a standard HDMI connector, and prevents accidental disconnection.
- HDFX-500- TR is compliant with HDMI standards features like CEC, EDID, and HDCP 2.2 for better installation flexibility and compatibility. It also supports HDR to deliver a more realistic and objective video signal.
- HDFX-500- TR can be operated by either USB power or DDC 5V power from an HDMI source (Tx only). Auto Power-Switching feature makes it more reliable on its power supply.
System Requirements for Setup
- Hardware requirements
- You must have an HDMI source and display. It should support the maximum graphic resolution feature of displays to be connected.
- No special requirements of memory size, CPU speed, and chipsets, if you’ve already properly installed your HDMI systems or graphic cards.
- A proper initial trial of the entire platform with its application using a short-length copper cable is recommended prior to installation with the optical link.
- Software requirements
- No special restrictions, if you’ve already properly installed your HDMI systems.
- Power Technical Advisory
- Enclosed Power Adaptors and USB cables supply power to both Transmitter and Receiver.
- Connection Advisory
- It is highly recommended that the HDMI source is directly connected to HDMI display output via HDFX-500-TR without connection to the incompatible distributor, switcher, and selector.
The Shipping Group of HDFX-500-TR;
- One (1) Transmitter (Tx) and One (1) Receiver (Rx) Two (2) Micro USB to USB cables
- Two (2) 5V 1A power adapter
- User Manual
- HDMI male to HDMI female Cable (0.2m)
Installation
Important: Please keep the installation procedure below. Improper or no
operation may result if the start-up sequence is not correctly followed.
Step 1
Carefully unpack the contents in the shipping group.
Step 2
Power on the HDMI source and display. HDFX-500-Tx can be turned on by DDC 5V
from pin #18 of HDMI interface, whereas both transmitter and receiver can be
operated by USB power. Opticis recommend USB power supply for stable power
supply for both the transmitter and receiver.
Step 3
Power LED will turn on when HDFX-500-TR is connected to HDMI signal source and
display and Status LED will blink three (3) times. Then Status LED will blink
again when the whole connection is made.
Step 4
Connect one (1) LC optical fiber between the transmitter and the receiver.
Ensure the connectors are fully engaged and then, the top LED will begin to
blink regularly.
Note1: Please DO NOT look directly into the LC receptacles of the
Transmitter when it is powered on. Although this product is regulated strictly
enough to operate under the LASER Class I, classified by CDRH/FDA for eye
safety, it is not recommended to do so.
Note2: The maximum extension length by OM3 fiber is 200 meters (656ft.).
Note3: It is recommended NOT to use any intermediate cable or adapter
between them to avoid undesirable performance degradation.
Step 5
Connect the transmitter (HDFX-500-Tx) to the HDMI source
Step 6
Connect the receiver (HDFX-500-Rx) to the HDMI display.
Note: When power is supplied, Power LED will turn on. If the connection
is fully engaged, Status LED will blink.
Step 7
If the system does not work properly, go to the page 1-5 trouble shooting.
Troubleshooting
The display shows only black screen.
- Ensure that all plugs and jacks used by USB power supplies are firmly connected. Ensure that the LED is ON.
- Ensure that the HDMI connectors are firmly plugged in to the HDMI source and display.
- Ensure that the transmitter and receiver modules plugged correctly to the source and display, respectively.
- Check if the HDMI source and display are powered on and properly booted.
- Reset the system by de-plugging and re-plugging the transmitter HDMI or receiver HDMI, or by de-plugging and re-plugging the USB power cables that are plugged of the transmitter and receiver module
- Re-boot up the system while connecting the module.
Screen is distorted or displays noises.
- Check if the graphic resolution is properly set. Go to the display properties and tap the settings. Ensure that the resolution sets less than 4K UHD (4096×2160) at 60Hz refresh ratio.
- Reset the system
- Power down, disconnect and reconnect the optical system cable or USB power adaptors, and power up
Maintenance
No special maintenance is required for the optical system cables and power
supplies. Ensure that the cables and power modules are stored or used in a
benign environment free from liquid or dirt contamination.
There are no user serviceable parts. Refer all service and repair issues to
Opticis or its authorized distributor.
Technical Support and Service
For commercial or general product support, contact your reseller. For technical service, contact Opticis by email techsupp@opticis.com or visit its website at www.opticis.com
Product Specifications
- Supports HDMI 2.0 standards feature
- Extension limit: 200m (656feet) for 4K UHD (4096×2160) at 60 Hz (RGB & YCbCr : 4:4:4) refresh rate over one (1) LC OM3 fibers (50/125um).
- Graphic Transmission Bandwidth: Supports total data rate 18Gbps (6Gbps per Channel).
- Complies CEC, EDID & HDCP 2.2 Prevents accidental disconnection by using High-Retention HDMI connector
- Supports HDR at 10 bit or 12 bit speeds respectively within its maximum bandwidth, 18Gbps
- Mechanical specifications of transmitter and receiver Dimensions(WDH): 22mm x 67mm x 14mm
- Environmental Specifications
- Operating temperature: 0°C to 50°C
- Storage temperature: -30°C to 70°C
- Humidity: 10% to 85%
AC/DC Power Adapter
- Power Input: AC 100-240V, 50/60Hz.
- Power Output: +5 V, 1A SMPS DC-power Adapter
Warranty Information
(One) Year Warranty
Opticis warrants this optical HDMI module to be free from defects in workman
ship and materials, under normal use and service, for a period of one (1) year
from the date of purchase from Opticis or its authorized resellers.
If a product does not work as warranted during the applicable warranty period,
Opticis shall, at its option and expense, repair the defective product or
part, d eliver to customer an equivalent product or part to replace the
defective item, or refund to customer the purchase price paid for the
defective product. All products that are replaced will become the property of
Opticis. Replacement products may be new or reconditioned. Any replaced or
repaired product or part has a ninety (90) day warranty or the reminder of the
initial warranty period, whichever is longer. Opticis shall not be responsible
for any software, firmware, information, or me mory data of customer contained
in, stored on, or integrated with any product s returned to Opticis for repair
under warranty or not.
Warranty Limitation and Exclusion
Opticis shall have no further obligation under the foregoing limited warranty
if the product has been damaged due to abuse, misuse, neglect, accident,
unusual physical or electrical stress, unauthorized modifications, tampering,
alterations, or service other than by Opticis or its authorized agents, causes
other than from ordinary use or failure to properly use the product in the
application for which said product is intended.
Dispose of Old Electrical & Electronic Equipment
(Applicable in the European Union and other European countries with separate
systems) This symbol on the product or on its packaging indicates that this
product shall not be treated as household waste. Instead it shall be handed
over to the applicable collection point for the recycling of electrical and
electronic equipment. By ensuring this product is disposed of correctly, you
will help prevent potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate waste handling
of this product. The recycling of materials will help to conserve natural
resources. For more detailed information about recycling of this product,
please contact your local city office, your household waste disposal service
or the shop where you purchased the product.
Certifications
CE / FCC, Class 1 Laser Eye Safety
Certification of Eye Safety
This laser product is inside implemented by using 780, 825, 850, 930, 960,
990nm LD Transceivers, manufactured by Opticis Co., Ltd., which are all
certified by CDRH/FDA referred as classified in Laser Class 1 (IEC60825-1).
Caution – Use of controls or adjustments or performances of procedures other than those specified herein may result in hazardous radiation exposure.
Opticis Locations
OPTICIS HQ
- Opticis Co., Ltd.
- 3F, 305, Sanseong-daero
- Sujeong-gu, Seongnam-si
- Gyeonggi-do, 13354
South Korea
- Tel: +82 (31) 719-8033
- Fax: +82 (31) 719-8032
- www.opticis.com
For order support, please contact your Distributor or Reseller. For technical support, check with the Opticis web site www.opticis.com or contact techsupp@opticis.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>