OPTICIS DPFX-100-TR Two (2) fibers Detachable DisplayPort Extender User Manual

June 6, 2024
opticis

DPFX-100-TR Two (2) fibers Detachable
DisplayPort Extender
User ManualOPTICIS DPFX 100-TR Two 2 fibers Detachable DisplayPort
Extender

Welcome!
Congratulations on your purchase of the two (2) fibers DisplayPort extender, DPFX-100-TR. This manual contains information that will assist you in installing and operating the product.

Product Description

New compact optical DisplayPort extender, DPFX-100-TR enables to the transmission of WQXGA (2560×1600) at 60Hz and 4K (3840×2160) at 30Hz signal up to 200m (656feet),  avoiding any tricks like scaling or data compression for lessening a burden of data transmission. It provides total data throughput 10.8Gbps (2.7Gbps per lane).
The pure fiber connection by two (2) LC fibers connector between transmitter and receiver, gives clean, secure, and easy installation with perfect electrical isolation, but without electrical hazard and interference. The DPFX-100-TR can be operated by both USB power by plugging the USB cable and DC power included as a shipping group.

OPTICIS DPFX 100-TR Two 2 fibers Detachable DisplayPort Extender - figure
1

The Shipping Group of DPFX-100-TR;

  • One (1) Transmitter (Tx) and One (1) Receiver (Rx)
  • Two (2) DP copper cables (0.5m)
  • Two (2) USB to DP plug Cables
  • Two (2) DC +5V,1A power adapters
  • User Manual

System Requirements for Setup

Hardware requirements

  • You must have a DisplayPort source and display. It should support the maximum graphic resolution feature of displays to be connected.
  • No special requirements for memory size, CPU speed, and chipsets, if you’ve already properly installed your DisplayPort systems or graphic cards.
  • A proper initial trial of the entire platform with its application using a short-length copper cable is recommended prior to installation with the optical link.

Software requirements

  • No special restrictions, if you’ve already properly installed your DisplayPort systems.

Power Technical Advisory

  • Enclosed Power Adaptors and USB cables supply power to both Transmitter and Receiver.

Connection Advisory

  • It is highly recommended that the DisplayPort source is directly connected to DisplayPort display output via DPFX-100-TR without connection to the incompatible distributor,  switcher, and selector.

Installation

Important: Please keep the installation procedure below. Improper or no operation may result if the start-up sequence is not correctly followed.
Step 1
Carefully unpack the contents in the shipping group.
Step 2
Power on the DisplayPort source and display. Power on both transmitter and receiver by using a USB power cable or DC power adapter.
Step 3
Then, the LED (Green color) will begin to blink once a second for three (3) times regularly on both sides.OPTICIS DPFX 100-TR Two 2 fibers Detachable
DisplayPort Extender - figure 2

Step 4
Connect two (2) LC optical fibers between the transmitter and the receiver and each fiber channel shall be connected as A to A and B to B carefully.
Ensure the duplex connectors are fully engaged and then, the top LED will begin to blink regularly. OPTICIS DPFX 100-TR Two 2 fibers Detachable
DisplayPort Extender - figure 3

Note: Please DO NOT look directly into the LC receptacles of the Transmitter, while it is powered on, although this product is regulated strictly enough to operate under the  LASER Class I, classified by CDRH/FDA for eye safety.
Note1: The maximum extension length by multi-mode fiber is 200 meters.
Note2: It is recommended NOT to use any intermediate cable or adapter between them to avoid undesirable performance degradation.OPTICIS DPFX
100-TR Two 2 fibers Detachable DisplayPort Extender - figure
4

Step 5
Connect the transmitter to the DisplayPort source over a DisplayPort copper cable.
Step 6
Connect the receiver to the DisplayPort source over a DisplayPort copper cable.
Note: If the connectors are fully engaged, the bottom LED will turn on.
Step 7
If the system does not work properly, go to pages 1-5 of troubleshooting.

Troubleshooting

The display shows a black screen.

  • Ensure that all plugs and jacks used by USB power cables or external power supplies are firmly connected. Ensure that the LED is ON.
  • Ensure that the DisplayPort cables are firmly plugged in to the DisplayPort source and display.
  • Ensure that the transmitter and receiver modules are plugged correctly to the source and display, respectively.
  • Check if the DisplayPort source and display are powered on and properly booted.
  • Reset the system by de-plugging and re-plugging the transmitter and receiver, or by de-plugging and re-plugging the USB power cables that are plugged into the transmitter and receiver.
  • Re-boot up the system while connecting the module.

Screen is distorted or displays noises.

  • Check if the graphic resolution is properly set. Go to the Display Properties and tap the Settings. Ensure that the resolution sets less than WQXGA (2560×1600) at a 60Hz  refresh ratio.
  • Reset the system.
  • Power down, disconnect and reconnect the optical system cable or DC power adaptors, and power up.

Maintenance

No special maintenance is required for the optical system cables and power supplies. Ensure that the cables and power modules are stored or used in a benign environment free from liquid or dirt contamination.
There are no user-serviceable parts. Refer all service and repair issues to Opticis or its authorized distributor.

Technical Support and Service

For commercial or general product support, contact your reseller. For technical service, contact Opticis by email techsupp@opticis.com or visit its website at www.opticis.com.

Product Specifications

  • Compliance with DisplayPort standard: supports DP 1.1a

  • Extension limit: 200m (656feet) for WQXGA (2560×1600) at 60 Hz and 4K (3840×2160) at 30 Hz refresh rate over two (2) LC multimode fibers (50/125um).

  • Graphic Transmission Bandwidth: Supports total data rate 10.8Gbps (2.7Gbps per lane).

  • Supports Dual-mode DP (DP++)

  • Supports auxiliary /l²C channel over fiber

  •  Mechanical specifications of transmitter and receiver
    • Dimensions(WDH): 35mm x 72mm x 16mm

  • Environmental Specifications
    • Operating temperature: 0°C to 50°C
    • Storage temperature: -30°C to 70°C
    • Humidity: 10% to 85%

AC/DC Power Adapter

  • Power Input: AC 100-240V, 50/60Hz.
  • Power Output: +5 V, 1A SMPS DC-power Adapter
  • Cord DC Jack: Core is + 5 V and outer is GND.

Warranty Information

1 (One) Year Warranty
Opticis warrants this optical DP module to be free from defects in workmanship p and materials, under normal use and service, for a period of one (1) year from the date of purchase from Opticis or its authorized resellers.
If a product does not work as warranted during the applicable warranty period, Opticis shall, at its option and expense, repair the defective product or part, deliver to the customer an equivalent product or part to replace the defective item, or refund to the customer the purchase price paid for the defective product.
All products that are replaced will become the property of Opticis.
Replacement products may be new or reconditioned.
Any replaced or repaired product or part has a ninety (90) day warranty or the remainder of the initial warranty period, whichever is longer.
Opticis shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to  Opticis for repair under warranty or not.

Warranty Limitation and Exclusion
Opticis shall have no further obligation under the foregoing limited warranty if the product has been damaged due to abuse, misuse, neglect, accident, unusual physical or electrical stress, unauthorized modifications, tampering, alterations, or service other than by Opticis or its authorized agents, causes other than from ordinary use or failure to properly use the product in the application for which said product is intended.

Dispose of Old Electrical & Electronic Equipment
(Applicable in the European Union and other European countries with separate systems)
This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
The recycling of materials will help to conserve natural resources. For more detailed information about recycling this product, please contact your local city office, your household waste disposal service, or the shop where you purchased the product.

Certifications
CE / FCC, Class 1 Laser Eye Safety
Certification of Eye Safety
This laser product is inside implemented by using 1310, 1550nm LD Transceivers, manufactured by Opticis Co., Ltd., which are all certified by CDRH/FDA referred as classified in Laser Class 1 (IEC60825-1).

Caution – Use of controls or adjustments or performances of procedures other than those specified herein may result in hazardous radiation exposure.

Opticis Locations

OPTICIS HQ
Opticis Co., Ltd.
3F, 305, Sanseong-daero
Sujeong-gu, Seongnam-si
Gyeonggi-do, 13354
South Korea
Tel: +82 (31) 719-8033
Fax: +82 (31) 719-8032
www.opticis.com

For order support, please contact your Distributor or Reseller.
For technical support, check with the Opticis website www.opticis.com or contact techsupp@opticis.com
© 2021 Opticis Co., Ltd. All Rights Reserved
Revision 1.5. Jan 2021

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

opticis User Manuals

Related Manuals