LINDY 38152 4×4 HDMI 10.2G Matrix Switch User Manual

: June 6, 2024
: LINDY

Table of Contents

Introduction
Package Contents
Features
Specification
Operation
CE/FCC Statement
Documents / Resources

CONNECTION PERFECTION
4×4 HDMI 10.2G Matrix Switch
User Manual

Introduction

Thank you for purchasing the LINDY 4K HDMI 4×4 Matrix with remote control. This high-performance HDMI Matrix allows any of the attached four sources to be shown on any of the four displays simultaneously. An Infrared remote control is supplied to make switching between sources and displays easier.

Package Contents

HDMI 4×4 4K Matrix
12V 2.5A DC Multi-Country PSU
IR Remote control
9 Way serial cable
Mounting brackets and screws
This manual

Features

Supports display resolutions up to Ultra HD 4K 3840×2160 30Hz including 1080p 3D
3D HDMI 1.4a video format support
3D video support including Frame packing for all 3D formats up to a 297MHz TMDS clock
Supports deep color up to 48-bit per pixel
HDCP 1.4 support (INPUT), HDCP v1.4a protocol compliant (OUTPUT)
Supports the reception of any audio data conforming to the HDMI specification 1.4 such as L-PCM at up to 192kHz, compressed audio (IEC 61937), DSD, DST, DTS, and HBR
Full colorimetric including sYCC601, Adobe RGB, Adobe YCC601,xvYCC extended gamut color
Operates for TMDS clock frequencies up to 300MHz

Specification

Frequency Bandwidth: 2.97Gbps
Input Ports: 4 x HDMI Female input ports
Output Ports: 4 x HDMI Female output ports
Power Supply: DC 12V 2A
ESD Protection Human Body Model: ± 8kV (air-gap discharge) ± 4kV (contact discharge)
Dimensions: 267x120x32mm (WxDxH)
Weight: 839g
Operating Temperature: 0°C ~ 40°C / 32°F ~ 104°F
Storage Temperature: -20°C ~ 60°C / -4°F ~ 140°F
Relative Humidity: 20 ~ 90% RH (Non-condensing)
Power Consumption: 20W Max

Operation

Front Panel:

ON/OFF: Power on/off switch
POWER: This red LED illuminates when the device is connected with power supply
IR IN: Remote control signal receive
OUTPUT A: Press this button to select the input source to HDMI OUTPUT A, and the red LED will illuminate when selecting the corresponding input
OUTPUT B: Press this button to select the input source to HDMI OUTPUT B, and the red LED will illuminate when selecting the corresponding input
OUTPUT C: Press this button to select the input source to HDMI OUTPUT C, and the red LED will illuminate when selecting the corresponding input
OUTPUT D: Press this button to select the input source to HDMI OUTPUT D, and the red LED will illuminate when selecting the corresponding input

Rear Panel:

INPUT PORTS: The LED’s will illuminate when a HDMI signal is detected
OUTPUT PORTS: The LED’s will illuminate when the TV signal is detected
RS232: This port can control the matrix via a PC
DC 12V: Plug the 12V DC power supply into the unit and connect the adapter to the AC wall outlet

Remote control:

OUT A: Press any of the four buttons to select a source signal
OUT B: Press any of the four buttons to select a source signal
OUT C: Press any of the four buttons to select a source signal
OUT D: Press any of the four buttons to select a source signal

Software Control:

General page

Control mode select: Only COM control mode is supported with this model
Select RS232 COM port
Click to connect or disconnect PC and Matrix
Click to refresh device status
To enable or disable Input/Output tags displayed when setting buttons on “Setting” page
Click to select a tab
Status bar:
RS232 COM port connection
Communication status
Prompt of operation messages
Time and Date
Device information display area

Port Tag Page:

Input port tags
Click to edit Input port tags
Output port tags
Click to edit Output port tags

Edit Input port tags:
To edit the INPUT port tags, click edit and then add your own name in the area provided

Edit Output port tags:
To edit the OUTPUT port tags, click edit and then add your own name in the area provided

Setting page:

Display’s the Input number for respective Output
Click to select Input port for respective Output port
Click to select previous or next Input port for respective Output port
Display Input to Output with tag information when the mouse moves over the buttons referred to in 2
Pre-Setting items
Click to edit the selected pre-setting item
Set selected pre-setting item to Matrix

EDID Control page:

Set EDID mode for selected Input port or All Input ports, click “Set” button to complete an action. “Auto EDID mode” can only be set for “All Inputs”
Copy EDID from Output port to selected Input port or All Input ports, click “Copy” button to complete action
Read EDID content from Output port and display in the grid, click “Read” button to complete action
Save EDID content which is displayed in grid to a binary file (file extension is “.bin”)
Open EDID binary file and display in grid
Download EDID content which displayed in grid to the selected Input port or All Input ports, click
“Download” button to complete action
EDID content displaying grid
Click to clear EDID content displayed in grid

Advanced Page:

Enable and disable IR control
3. & 4. TCP Mode is not supported

FW upgrade Page:
Firmware upgrade is not supported on this model
EDID Dipswitch:
Adjust the dip switches on the side of the matrix to force the required setting:

(0 is down, 1 is up)

0000 Auto mode (default)
0001 1080i, Stereo Audio 2.0
0010 1080i, Dolby/DTS 5.1
0011 1080i, HD Audio 7.1
0100 1080p, Stereo Audio 2.0
0101 1080p, Dolby/DTS5.1
0110 1080p, HD Audio 7.1
0111 3D, Stereo Audio 2.0
1000 3D, Dolby/DTS5.1
1001 3D, HD Audio 7.1
1010 4Kx2K, Stereo Audio 2.0
1011 4Kx2K, Dolby/DTS5.1
1100 4Kx2K, HD Audio 7.1
1101 1024×768 DVI
1110 1920×1080 DVI
1111 PC Control

CE/FCC Statement

CE Certification
LINDY declares that this equipment complies with relevant European CE requirements.
UKCA Certification
LINDY declares that this equipment complies with relevant UKCA requirements.

FCC Certification
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
The enclosed power supply has passed Safety test requirements, conforming to the US American versions of the International Standard IEC 60950-1 or 60065 or 62368-1.

Manufacturer (UK):
LINDY Electronics Ltd
Sadler Forster Way
Stockton-on-Tees, TS17 9JY
England
sales@lindy.co.uk, T: +44 (0)1642 754000

Recycling Information
WEEE (Waste of Electrical and Electronic Equipment), Recycling of Electronic Products

Europe, United Kingdom
In 2006 the European Union introduced regulations (WEEE) for the collection and recycling of all waste electrical and electronic equipment. It is no longer allowable to simply throw away electrical and electronic equipment. Instead, these products must enter the recycling process.
Each individual EU member state, as well as the UK, has implemented the WEEE regulations into national law in slightly different ways. Please follow your national law when you want to dispose of any electrical or electronic products. More details can be obtained from your national WEEE recycling agency.
Battery Remark:
Do not put empty batteries in your domestic waste bin as they will not be recycled. Empty batteries can be returned for recycling at our trade counter or at your local household recycling centre.
The raw materials enclosed in batteries such as Zinc, Iron, and Nickel can be reused to a very large proportion. Recycling batteries and disused/obsolete electronic equipment is one of the most efficient environmental protection actions you can easily take.

Tested to comply with
FCC standards.
For home and office use.
No. 38152
2nd
Edition, January 2021
lindy.com