LINDY 38148 6×2 HDMI 10.2G Matrix with PiP User Manual
- June 6, 2024
- LINDY
Table of Contents
6×2 HDMI 10.2G Matrix with PiP
User Manual
.
No. 38148
lindy.com
© LINDY Group – THIRD EDITION (January 2021)
Safety Instructions
! WARNING!
Please read the following safety information carefully and always keep this
document with the product.
Failure to follow these precautions can result in serious injuries or death
from electric shock, fire or damage to the product.
Touching the internal components or a damaged cable may cause electric shock,
which may result in death.
This device is a switching type power supply and can work with supply voltages
in the range 100 – 240 VAC For worldwide usability four different AC adapters
are enclosed: Euro type, UK type, US/Japan type, and Australia/New Zealand
type. Use the appropriate AC adapter as shown in the picture and ensure it is
firmly secured in place and does not detach by pulling before installing it
into a power socket.
To reduce risk of fire, electric shocks or damage:
- Do not open the product nor its power supply. There are no user-serviceable parts inside.
- Only qualified servicing personnel may carry out any repairs or maintenance.
- Never use damaged cables.
- Do not expose the product to water or places of moisture.
- Do not use this product outdoors it is intended for indoor use only.
- Do not place the product near direct heat sources. Always place it in a well-ventilated place.
- Do not place heavy items on the product or the cables.
- Please ensure any adapters are firmly secured and locked in place before inserting into a wall socket
Instructions for Use of Power Supply
Push the button and rotate anticlockwise to unlock and remove the adapter. To attach, push and rotate clockwise until the adapter is locked into place.
Introduction
Thank you for purchasing the 6×2 HDMI 10.2G Matrix with PiP. This product has been designed to provide trouble-free, reliable operation. It benefits from both a LINDY 2-year warranty and free lifetime technical support. To ensure correct use, please read this manual carefully and retain it for future reference. The Lindy 6×2 HDMI 10.2G Matrix Switch with PiP allows for simple switching between 6 HDMI source devices and distributing to 2 displays, while also providing the ability to display all 6 sources on a single display using the PiP (Picture in Picture) function.
Package Contents
- 6×2 HDMI 10.2G Matrix with PiP
- IR Remote with CR2025 battery
- 5VDC 2A Multi-country power supply (UK, EU, US & AUS), Barrel Size: 5.5/2.1mm
- Mounting brackets and screws
- Lindy Manual
Features
- Switch between 6 HDMI source devices and output to 2 displays
- PiP (Picture in Picture) mode allows for 1 main picture and 5 sub pictures on one display in 1920×1080@60Hz resolutions
- Supports resolutions up to 4096×2160@30Hz 4:4:4 8bit
- Supports MHL 2.0 via active cable up to 1920×1080@60Hz (HDMI In 6)
- Supports HDMI audio pass-through up to 7.1CH including LPCM@192KHz, Dolby True HD and DTS- HD Master Audio
- Digital & analog audio extraction (HDMI Out A)
- ARC extraction (HDMI Out A)
- CEC Pass-through (HDMI In 1)
- Simple switching via push button or IR (remote included)
- Audio EDID management
Specification
- HDMI 1.4 10.2Gbps
- HDCP 2.2 (HDMI In 1) / HDCP 1.4 (All other inputs)
- ESD Protection: ± 8kV (air-gap discharge)
- Human Body Model: ± 4kV (contact discharge)
- IR Support: 20-60kHz
- Operating Temperature: 0°C – 40°C (32°F – 104°F)
- Storage Temperature: -20°C – 60°C (-4°F – 140°F)
- Humidity: 20 – 90% RH (non-condensing)
- Black, metal housing
- Power Requirements: AC100-240V 50/60Hz
- Power Consumption: 10W
Connections
- Input: 6 x HDMI Type A (Female)
- Output: 2 x HDMI Type A (Female), 3.5mm (Female), TosLink (Optical) (Female)
Installation and Operation
Front Panel
-
ON/OFF: Power the matrix on or off.
-
Input LED (1-6): The corresponding LED will illuminate once an active HDMI source device has been connected. A/B indicates the corresponding output the source device is switched to.
-
EDID LED: This LED will illuminate when the corresponding audio EDID has been selected.
-
ARC LED: This LED will illuminate when the ARC function has been selected.
Please note: ARC is only possible when using HDMI Output A -
Power LED: This LED will illuminate when the matrix is connected with a power supply and switched on.
-
Out A Button: Press this button to select the source for output A.
-
Out B Button: Press this button to select the source for output B.
-
EDID Button: Press this button to select the audio output EDID: 2.0CH / 5.1CH / 7.1CH
-
ARC Button: Press this button to select the ARC function.
-
RST Button: Press this button to reset back to factory default settings (Input 1, 2.0CH Audio, ARC off)
-
IR: IR receiver eye for control via the IR remote (included).
Rear Panel
- HDMI Input: Connect an HDMI source to the desired port using an HDMI cable.
- HDMI Output: Connect an HDMI display to the desired port using an HDMI cable.
- 3.5mm Output: Extract analog 2CH audio to an amplifier or stereo speakers.
- TosLink (Optical) Output: Extract digital audio to an amplifier, speakers or soundbar.
- 5VDC: Connect the 5VDC 1A PSU to an AC wall outlet and securely connect to the matrix.
Please note:
Audio will only be extracted to 3.5mm and TosLink (Optical) from HDMI Out A.
The audio EDID must be set to 2CH when using the 3.5mm connection otherwise no
audio will be output.
HDCP 2.2 is only supported on HDMI In 1.
MHL is only supported on HDMI In 6. Active MHL to HDMI cable is required (not
included).
ARC is only supported on HDMI Out A. To use ARC the connected display must
also support ARC.
When ARC is not selected, the matrix will output audio from the selected
source device. When ARC is selected, ARC signal from the TV will be used.
Picture in Picture Layouts
This matrix allows for content from multiple source devices to be shown on a
single display using Picture in Picture mode. The layouts are shown below.
Infrared Control
- Power button: Power the matrix on or off.
- Audio: Press to cycle through the audio output EDID.
- ARC: Press to activate or de-activate ARC.
- PiP: Press to activate PiP mode. The displays connected to HDMI Out A and HDMI Out B will switch to the same HDMI source device.
- Select: Press to cycle through the HDMI source device connections for Picture in Picture mode.
- Enter: Press to confirm the selected HDMI source device for Picture in Picture mode.
- Out A: Press the corresponding Input to output to HDMI Out A.
- Out B: Press the corresponding Input to output to HDMI Out B.
CE/FCC Statement
CE Certification
LINDY declares that this equipment complies with relevant European CE
requirements.
CE Konformitätserklärung
LINDY erklärt, dass dieses Equipment den europäischen CE-Anforderungen
entspricht
UKCA Certification
LINDY declares that this equipment complies with relevant UKCA requirements.
FCC Certification
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
You are cautioned that changes or modifications not expressly approved by the
party responsible for compliance could void your authority to operate the
equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired
operation.
The enclosed power supply has passed Safety test requirements, conforming to the US American versions of the International Standard IEC 60950-1 or 60065 or 62368-1.
Recycling Information
WEEE (Waste of Electrical and Electronic Equipment),
Recycling of Electronic Products
Europe, United Kingdom
In 2006 the European Union introduced regulations (WEEE) for the collection
and recycling of all waste electrical and electronic equipment. It is no
longer allowable to simply throw away electrical and electronic equipment.
Instead, these products must enter the recycling process.
Each individual EU member state has implemented the WEEE regulations into
national law in slightly different ways.
Please follow your national law when you want to dispose of any electrical or
electronic products. More details can be obtained from your national WEEE
recycling agency.
Battery Remark:
Do not put empty batteries in your domestic waste bin as they will not be
recycled. Empty batteries can be returned for recycling at our trade counter
or at your local household recycling center.
The raw materials enclosed in batteries such as Zinc, Iron, and Nickel can be
reused to a very large proportion. The recycling of batteries and
disused/obsolete electronic equipment is one of the most efficient environment
protection actions you can easily take.
Manufacturer (UK):
LINDY Electronics Ltd
Sadler Forster Way
Stockton-on-Tees, TS17 9JY
England
[email protected], T: +44 (0)1642 754000
No. 38148
3rd
Edition, January 2021
lindy.com