LINDY 37578 100m Cat.6 VGA Extender User Manual

LINDY 37578 100m Cat.6 VGA Extender
User Manual

Introduction

Thank you for purchasing the 100m Cat.6 VGA Extender. This product has been designed to provide trouble-free, reliable operation. It benefits from both a LINDY 2-year warranty and free lifetime technical support. To ensure correct use, please read this manual carefully and retain it for future reference.
The Lindy 100m Cat.6 VGA Extender is a high-quality solution for extending analog VGA signals over longer distances using a standard network cable. Supporting resolutions up to 1920×1080, this system provides excellent picture quality in classrooms, lecture halls, or presentations.

Package Contents

• Transmitter Unit
• Receiver Unit
• 2 x Pack of Screws for Mounting
• Lindy Manual

Features

• Supports resolutions up to 1920×1080 ­ for a full list of resolutions and distances please see below
• In-built virtual DDC
• In-built sync mode selection (Tx)
• Selectable Sync
• Filter (Rx) Mountable
• Black, metal housing
• Passive Extension ­ no external power required

Specification

• Transmitter
  Input: VGA (Female), Output: RJ-45 (Female)

• Receiver
  Input: RJ-45 (Female), Output: VGA (Female)

• Horizontal & Vertical Sync: TTL standard

• Maximum Bandwidth: 300MHz

• Insertion Loss: <3dB Video

• Signal Return Loss: -15dB

• Maximum from DC to 60Mhz

• Impedance: 75 Ohms (DB15), 100 Ohms (RJ45)

• Operating Temperature: 0°C – 55°C (32°F – 131°F)

• Storage Temperature: -20°C – 85°C (-4°F – 185°F)

• Humidity: 0 – 95% RH (non-condensing)

Installation

1. Connect the Transmitter Unit to the source device using a VGA cable.
2. Connect the Receiver Unit to the display using a VGA cable.
3. Connect the Transmitter and Receiver Units together using Cat.6 UTP or higher cable at the desired length. Switch on all connected devices. The installation is now complete.

Please note: some monitors are more sensitive to the sync mode setting. In this scenario, please use STP Cat.X cabling.

Operation

Sync Mode Selection (Transmitter)

• On the Transmitter Unit, a small switch allows for control over the system two sync mode option.
• For modern monitors, it is advised that the switch should be set at Mode 1 for optimum stability.
• For legacy monitors including CRTs, it is advised that the switch should be set at Mode 2 for optimum stability.
• If there are any stability issues, please try the opposing sync mode

Sync Filter Dipswitch (Receiver)

• On the Receiver Unit, a Sync Filter dipswitch allows for adjustment to ensure a stable signal.
• Please adjust accordingly for which option provides the best stability for the connected display.

CE/FCC Statement

CE Certification
LINDY declares that this equipment complies with relevant European CE requirements.
FCC Certification
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

The enclosed power supply has passed Safety test requirements, conforming to the US American versions of the International Standard IEC 60950-1 or 60065 or 62368-1.

Hersteller / Manufacturer (EU):
LINDY-Elektronik GmbH
Markircher Str. 20 68229
Mannheim Germany
Email: info@lindy.com ,
T: +49 (0)621 470050
Manufacturer (UK):
LINDY Electronics Ltd
Sadler Forster Way
Stockton-on-Tees, TS17 9JY
England sales@lindy.co.uk,
T: +44 (0)1642 754000

Recycling Information
WEEE (Waste of Electrical and Electronic Equipment), Recycling of Electronic Products

Europe, United Kingdom
In 2006 the European Union introduced regulations (WEEE) for the collection and recycling of all waste electrical and electronic equipment. It is no longer allowable to simply throw away electrical and electronic equipment. Instead, these products must enter the recycling process.
Each individual EU member state has implemented the WEEE regulations into national law in slightly different ways. Please follow your national law when you want to dispose of any electrical or electronic products. More details can be obtained from your national WEEE recycling agency. No. 37578 2nd Edition, January 2021
lindy.com

References

• Lindy Electronics

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>