ROBUS R100LEDCCT3E-01 Golf White Round LED Bulkhead Luminaire Instruction Manual

ROBUS R100LEDCCT3E-01 Golf White Round LED Bulkhead Luminaire Instruction Manual

PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCES.

Electrical products can cause death or injury, or damage to property. If in any doubt about the installation or use of this product, consult a competent electrician

Installation

1. Ensure mains supply is switched off before commencing work.

2. Ensure there is at least 100mm of free space around the luminaire location.

3. Remove trim/ diffuser and LED plate from base of the fitting.

4. Drill cable entry and mounting holes in the base.

5. Mark fixing hole positions on wall, check location of buried cables, pipes or other building services before drilling.

6. Feed supply cables through cable entry hole and attach base to surface of wall.

7. Write installation date on battery and connect battery.

8. Connect wires from unswitched supply to terminals on metal plate, brown to PL, Blue to N and green/yellow to earth. For fitting always on, link terminal SL to terminal PL. For fitting controlled by switch, connect switched live wire to terminal SL and permanent live to PL.
   Note: if SL terminal not connected, fitting works as non maintained.

9. Move switch on top of the driver to select colour temperature: 3000K, 4000K or 6500K.

10. Refit LED plate and trim/ diffuser to base.
    Attention: In order to protect the battery life, please disconnect the
    battery if the power supply shut off over 3 days.

WARNING: DO NOT CHANGE CCT WHEN THE FITTING IS ON!

Switch on supply:

The green led should come on indicating correct battery charge status, all LEDs will come on. When supply to the switched live PL is lost, battery will operate fitting in emergency mode.
Market Surveillance:
LS Code of energy efficiency Class E.
R100LEDCCT3S-LS; R150LEDCCT3S-LS
Disconnect driver input and output connections. Remove LED plate.

Testing

The emergency lighting must be inspected and tested regularly in accordance with local codes of practice. Note: for safety reasons tests should be carried out during daylight hours. The minimum recommended test schedule is as follows: After installation, allow 24 hours to ensure full battery charge and then interrupt the supply; the maximum duration time is 3 hours. Check that LEDs are still lighting.

1. Daily check that charge indicator LED is working.
2. Monthly, interrupt mains for a short period and check LED lights.
3. Annual 12 month check, full duration test. Interrupt mains supply, LEDs will light and should last for a minimum 3 hours operation: batteries must be replaced when they can no longer support 3 hour operation.
4. Complete record sheet on installation and retain in maintenance file.
5. Update file with ongoing test records for inspection by fire officer or other duly authorised person.

Information for the Product user

1. Please note the requirement to dispose of Waste Electrical & Electronic Equipment separately from household waste (WEEE marked with crossed out wheelie bin symbol).
2. Please consider your role in contributing to re-use and recycling by returning this product at end of life to a collection centre for waste electrical equipment or a Civic Amenity site, or to a retail outlet from which you are purchasing a replacement.
3. This equipment may contain substances that are hazardous to health and the environment if disposed of carelessly. It is important that it is separated from normal household waste and recycled in the WEEE chain
4. The “crossed out wheelie bin symbol” on a product indicates this equipment must not be disposed of in normal household waste, but should be disposed of according to local WEEE regulations

Installation and Maintenance Record

Installer
Installation
Type
Installation test duration & Date

Warranty

2 Years

-10°C < Ta < +40°C, 220V – 240V ~ 50/60Hz, Class I, IP65, Battery Warranty: 2 Years
Luminaire is non-dimmable
Suitable for mounting on a normally flammable surface

Product technical information and specification may change over  time without prior notification. For the latest technical information please visit our web site www.robus.com or robusdirect.com

Customer support

L.E.D lighting & Electrical Distribution Group UC
IRE: Nangor Road, Dublin 12, D12 E7VP, Ireland
UK: Bracknell Enterprise & Innovation Hub, Ocean
House, 12th Floor, The Ring, Bracknell,
Berkshire RG12 1AX, UK

Tel: +353 1 7099000
Fax: +353 1 7099060
Email: info@robus.com
Website: www.robus.com

References

• robusdirect
• ROBUS: Home to Best-in-Class LED Lighting and Customisation - Robus
• ROBUS: Home to Best-in-Class LED Lighting and Customisation - Robus

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>